Fabricante:
(Categoria: 106)
pressure: 250 tthroat: 360 mmtable-size: 1.250 x 630 mmtable diameter: 250 mmdimension of ram: 850 x 450 mmdayligth: 800 mmpiston stroke: bis 500 mmdiameter of piston: 400/360 mmram stroke speed: abwärts 200 mm/secram stroke speed: aufwärts 110 mm/sectotal power requirement: 20,5 kWweight of the machine ca.: 8 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 250 tthroat: 360 mmtable-size: 1.250 x 630 mmtable diameter: 250 mmdimension of ram: 850 x 450 mmdayligth: 800 mmpiston stroke: bis 500 mmdiameter of piston: 400/360 mmram stroke speed: abwärts 200 mm/secram stroke speed: aufwärts 110 mm/sectotal power requirement: 20,5 kWweight of the machine ca.: 8 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 3,3 bei 6bar tdayligth: 250 mmstroke: 70 mmwork stroke: 10 mmtable surface area: 220x190 mmthroat: 150 mmweight of the machine ca.: 350 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 30 tstroke: 300 mmdaylight between the columns: 700 mmdayligth: 850 mm: 140 mmdiameter of piston: 60 mmtable surface area: 700 x 390 mmweight of the machine ca.: 0,35 tdimensions of the machine ca.: 1,2 x 0,8 x 2,2 mWorkshop Press- Movable cylinder- 2 support prisms- Emergency stop deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 25 tthroat: 250 mmstroke: 400 mmtable surface area: 600x480 mmram surface: Ø135 mmtable height: 980 mmweight of the machine ca.: 1,5 tdimensions of the machine ca.: 2000x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 tchamfer lenght: 3200 mmControl: CYBELEC CybTouch 15 PS weight of the machine ca.: 14.000 kgdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40.0 tchamfer lenght: 1600 mmdistance between columns: 1100 mmstroke of upper beam: 100 mmthroat: 195 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sec: 180 barwork height max.: 840 mmtable width: 110 mmdayligth: 295 mmControl: ATS 585 total power requirement: 5.5 kWweight: 2500 kgrange L-W-H: 2100 x 1200 x 1800 mmFurnishing:- NC controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control ATS 560 Positioning of the backgauge (X axis) Depth setting positioning (Y1+Y2 axis) Possibility of programming different programs Storage capacity max. 200 programs - max. 400 sentences Pivoting control panel, left front- electric back gauge (X axis) with 2 stop fingers, manually adjustable (R+Z axis)- System A tool holder - with cambered upper wedge- Split insert/bending tools- side protection grids- rear protection- free-moving double foot switch- Operation manualThe d ...
pressure: 40 tthroat: 230 mmstroke: 4-100 mmtable surface area: 650x450 mmram surface: 420x220 mmram - range of adjustment: 85 mmhole in the table: 170x220 mmtable height: 800 mmno. of strokes: 60 Hub/mindayligth: 375 mmDimensions (HxWxD): 2800x1200x1900 mmweight of the machine ca.: 3,2 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 80 tthroat: 300 mmstroke: 8-110 mmno. of strokes: 100 Hub/minram - range of adjustment: 75 mmtable surface area: 750x590 mmram surface: 540x400 mmhole in the table: 200x200 mmtable height: 780 mmtool hole in ram: Ø 40 mmtotal power requirement: 11 kWweight of the machine ca.: 5,5 tdimensions of the machine ca.: BxTxH 1200x1700x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press capacity: 45 ton Ram stroke adjustable: 10 - 40 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 220 - 300 mm Free frontal opening L-R: 560 mm Table surface area : 550 x 450 mm Slide area: 550 x 360 mm Hole in table: 450 x 100 mm Number of strokes: 100 - 500 s.p.m. Required power: 7,5 kW Weight of machine approx.: 6,2 ton
Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l
Press capacity: 50 ton Throat depth: 265 mm Stroke: 250 mm Daylight: 400 mm Table surface area : 700 x 450 mm Slide area: 550 x 300 mm Table height over floor: 850 mm Approach speed: 32 mm / sec Working speed: 6,3 mm / sec Return speed: 42 mm / sec Required power: 4 kW Dimensions L x W x H: 1290 x 1160 x 2085 mm Weight of machine approx.: 1,75 ton
Press capacity: 125 ton Ram stroke adjustable: 30 - 120 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 450 mm Free frontal opening L-R: 1.290 mm Free lateral opening F-B: 450 mm Table surface area : 1.250 x 800 mm Slide area: 1.250 x 650 mm Hole in table: 1.050 x 260 mm Number of strokes: 30 - 220 s.p.m. Table height over floor: 1.200 mm Required power: 39 kW Height over floor approx.: 3.800 mm Dimensions L x W x H: 3.500 x 2.200 x 3.800 mm Weight of machine approx.: 21,5 ton
Press capacity: 45 ton Ram stroke adjustable: 20 - 80 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 300 mm Free frontal opening L-R: 710 mm Table surface area : 700 x 450 mm Slide area: 700 x 360 mm Hole in table: 600 x 100 mm Number of strokes: 80 - 400 s.p.m. Required power: 10 kW Height over floor approx.: 2900 mm Weight of machine approx.: 7,2 ton Control: Siemens S7
Press capacity: 80 ton Ram stroke adjustable: 4 -60 mm Slide adjustment: 0 - 80 mm Shut height (stroke down, adjustment up): 310 mm Free frontal opening L-R: 800 mm Table height over floor: 1150 mm Table surface area : 780 x 640 mm Slide area: 800 x 460 mm Hole in table: 690 x 170 mm Number of strokes: 30 - 300 s.p.m. Required power: 21 kW Height over floor approx.: 2900 mm Weight of machine approx.: 12 ton Control: Siemens S5
Press capacity: 35 ton Ram stroke adjustable: 6 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 250 mm Free frontal opening L-R: 430 mm Table surface area : 410 x 410 mm Slide area: 307 x 187 mm Hole in table: 170 x 110 mm Number of strokes: 60 - 300 s.p.m. Weight of machine approx.: 2,4 ton
Pressure total: 250 ton Ram stroke: 70 / 250 mm Slide adjustment: 160 mm Ejector in ram: 20 ton Ejector stroke in ram: 10 mm Shut height (stroke down, adjustment up): 520 mm Free lateral opening F-B: 1.300 mm Table surface area : 1.600 x 1.600 mm Slide area: 1.600 x 1.600 mm Number of strokes: 0 - 50 s.p.m. Required power: 33 kW Height over floor approx.: 5.500 mm Weight of machine approx.: 58 ton Roll feeder Material width: 1250 mm Material thickness: 0,3 - 1,6 mm Control: Siemens S7
pressure: 400 tchamfer lenght: 4050 mmdistance between columns: 3550 mmcontrol: CYBELEC ModEva 10 S total power requirement: 47 kWweight of the machine ca.: 30.400 kgdimensions of the machine ca.: 6000x3000x3450 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 tchamfer lenght: 4100 mmControl: CYBELEC DNC 900 stroke: 260 mmweight of the machine ca.: 16.000 kgdimensions of the machine ca.: 4500x2400x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 125 tchamfer lenght: 3000 mmdistance between columns: 3100 mmControl: Delem DA 66S stroke: 300 mmdayligth: 500 mm: 200 mm/sbending speed: 0-12 mm/stotal power requirement: 15 kWweight of the machine ca.: 10.000 kgdimensions: 4200x2200x2900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 180 tchamfer lenght: 3100 mmdistance between columns: 3600 mmControl: Cybelec CybTouch 15 stroke: 250 mmdayligth: 470 mm: 180 mm/sbending speed: 0-10 mm/s: 165 mm/stotal power requirement: 15 kWweight of the machine ca.: 12.500 kgdimensions: 4000 x 2000 x 3030 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Capacity: 80 ton Throat depth: 280 mm Ram stroke: 8 - 140 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 520 mm Table surface area : 850 x 670 mm Slide area: 550 x 400 mm Hole in table: 250 x 180 mm Number of strokes: 20 - 100 s.p.m. Required power: 7,5 kW Dimensions L x W x H: 2210 x 1510 x 2750 mm Oil volume: 50 l Die weight at the ram max.: 300 kg Weight of machine approx.: 8,3 ton
pressure: 135 tchamfer lenght: 2550 mmdistance between columns: 2050 mmcontrol: CYBELEC ModEva 10 S total power requirement: 25 kWweight of the machine ca.: 11.000 kgdimensions of the machine ca.: mMachine:- Sturdy machine frame constructed as a fully welded all-steel structure- Pressure beam with high bending strength- Electrohydraulic top drive via proportional valves- Modern block hydraulic systemOptional equipment:- Increase in installation height and stroke by 150 mm each- Backgauge system 2 - 2 axes, R-axis adjustment 150 mm- 2 x additional stop fingers 2/4-axes, however, offset by 20 mm- CNC holding device- Distance from the bending line to the holding device approx. 240 mm- EHT quick-clamping device for EHT upper tools, pneumatic, head width 26 mm, horizontally self-centering- EHT lower tool clamping, mounting width 55 mm, pneumatic- Hardened insert strip for EHT lower tool clam ...
pressure: 50 tchamfer lenght: 1550 mmdistance between columns: 1150 mmControl: CYBELEC DNC 1200 PS Eco column arm: 405 mmtable height: 900 mmstroke of ram: 400 mmdistance between table / ram: 720 mmtotal power requirement: 9,5 kWweight of the machine ca.: 5.200 kgdimensions of the machine ca.: 2000x1900x2920 mmAccessories/Equipment:- CYBELEC DNC 1200 PS Eco controller- 2 support arms- 4 stop fingers- Lasersafe- Foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 170 tchamfer lenght: 3050 mmdistance between columns: 2550 mmstroke: 400 mmweight of the machine ca.: 15.300 kgdimensions of the machine ca.: mMachine:- Sturdy machine frame- Press beam- Spherical bearing for the press beam with press beam tilt- Electro-hydraulic top drive- Block hydraulic system- Length measuring system (Y-axis) with dynamic spring compensation- Control cabinet air conditioning unit- Adapter strip for tool mounting- 2 stop fingersOptional equipment:- 2-axis backgauge (XM/XS, R)- 1 sheet metal holding device 200 daN CNC- 2 x additional stop fingers 2/4-axis- 1 x pneumatic upper tool clamping 26 mm- 1 x pneumatic lower tool clamping 55 mm- 1 x lower tool shift EHT pneumatic- 1 x CNC crowning device 3000 kN/m- 1 x Operator Safety Guard PILZ PSENvip Productive- 2 x Bending aid 1500 N- 1 x Support strips for bending aid- 1 x Parking position right, short- 1 x Spec ...
pressure: 1.000 tnominal power: 10.000 kNstroke length max.: 1.650 mmworking feed: 62 mm/secweight of tools max.: 40.000 kgvoltage: 400 Vtotal power requirement: 420 kWweight of the machine ca.: 254 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tstroke: 300 mmtable surface area: 500 x 1520 mmcolumn travel between the guideways: 1520 mmdayligth: 680 mmpressure: max. 244 barweight of tools max.: 270 kgajustment speed: 8.0 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secoil volume: 90.0 lvoltage: 400 Vtotal power requirement: 7.5 kWweight of the machine ca.: 2700 kgdimensions of the machine ca.: 2630 x 1000 x 2350 mm current new price approx. 18.000 euros special price on request according to previous owner rarely in useEquipment:- robust electro-hydraulic workshop/bending press left right guided- with fixed working cylinder- Pressing depth adjustable by cams- Height-adjustable work table- 2x locking bolts for table fixation- 3x directional control valve supply-empty-return- Stepless adjustment of working pressure- 1x freely movable 2-hand operation- Original operating instructionsThe data for this ad was crea ...
pressure: 28 tpiston stroke: 180 mmdiameter of piston: 130 mmtable-size: 300 x 550 mmworking feed: 2 - 9,8 mm/sekreturn speed: 20 mm/secMax. pressure: 200 barbending capacity - flat iron: 200 x 10 mmweight of the machine ca.: 800 kgdimensions: ca. 1150 x 1103 x 750 mmThe horizontal hydraulic press (28 ton) can be used for many different metal working jobs. The press has a piston stroke of 192 mm and can be equipped with all kinds of tooling for specific bending or straightening jobs. We supply a standard toolingset with this press including a stampholder and backgauge. However, we also produce custom-made tooling for your specific request. Thanks to the NC-control you can easily set the cylinder stroke and save up to 100 working cycles.With this horizontal hydraulic press you are able to bend, straighten, notch, cut and form. A universal hydraulic press that serves all your needs in cold ...
Pressure total: 800 ton Ram stroke: 700 mm Slide adjustment: 600 mm Shut height (stroke down, adjustment up): 1500 mm Free frontal opening L-R: 3800 mm Free lateral opening F-B: 1450 x 1100 mm Table surface area : 3500 x 1900 mm Slide area: 3500 x 1900 mm Die cushion capacity in table: 150 ton Die cushion stroke: 250 mm Die cushion pad area: 2780 x 1570 mm Number of strokes: 7 - 18 s.p.m. Required power: 120 kW Height over floor approx.: 9510 mm Weight of machine approx.: 260 ton
pressure: 90.0 tchamfer lenght: 3050 mmdistance between columns: 2550 mmstroke of upper beam: 135 mmdayligth: 180 mmthroat: 350 mmworking feed: 8.0 mm/secreturn speed: 68.0 mm/secwork height max.: 805 mmback stop - adjustable: max. 620 mmControl: ENC 310 oil volume: 100 ltotal power requirement: 7.5 kWweight: 5840 kgrange L-W-H: 4000 x 2040 x 2450 mm from a maintenance workshop very good conditions ()- in checked conditions - machinevideo - https://www.youtube.com/watch?v=PIiHc2e7h28Features: - NC electro-hydraulic press brake- with DURMA NC control ENC 310 Illuminated LCD display X-axis control & value display Y-axis control & value display- Swiveling operator panel, front left- NC controlled axes: Y1/Y2 + X- NC electro-motorized backgauge (X-axis) with 2x manually adjustable backgauge fingers including lateral and height adjustment (Z+R axes)- NC electro-motorized depth adjustment (Y-a ...
