Fabricant:
(Catégorie: 107)
sheet width: 1350 mm: 3 mmsheet thickness for stainless steel: 1,5 mmrear stop: 600 mmtotal power requirement: 3 kWweight of the machine ca.: 1150 kgdimensions: 2030 x 1940 x 1220 mmStandard equipment:- All-steel welded construction with static and dynamic frame rigidityframe rigidity- Direct drive with brake motor- Specially alloyed cutting blades- 750 mm motorized, digitally adjusted backgauge with ball screwsrecirculating ball screws- Manual blade gap adjustment system- Mechanical sheet clamping system with plastic base- Work table with insert plates- foot switch for single and repeat cutting cycles- 1 x squaring arm 1000 mm long with metric scale- 2 x 800 mm front material support arms- Front stop- Finger protection - front and rear covers- Rear light guards- CE declaration of conformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
engraving field: 120 x 120 mmtable-size: 250 x 250 mmworkpiece weight: max 50 kgControl: Fobagraf machine weight ab.: 1000 kgmachine frame made of welded steel constructionCross slide, hard stone design, table top with steel stop ironHeight-adjustable laser headQuality-switched ND: YAG laser head, lamp-pumped, 100 WDeflection unit mounted on the laser head (with standard lens)Z-axis with gearbox and servo driveServo axis control with X-, Y-, and Z-axesWater-cooledControl: Fobagraf user software packageOperating system: Windows 2000operating hours: 17.388 hmanual includedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2540 mmplate thickness: 2 mmthickness at Niro-steel: 1,25 mmno. of strokes: 63 Hub/mincutting angle: 1,13 °table height: 750 mmtable width: 320 mmback stop - adjustable: 5,0-550 mmtotal power requirement: 3 kWweight of the machine ca.: 1300 kgEquipment:- manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range- 1x long side stop- 3x support arms- Free-moving foot switch- Sheet holding device for thin sheet blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2540 mmplate thickness: 2 mmthickness at Niro-steel: 1,25 mmno. of strokes: 63 Hub/mincutting angle: 1,13 °table height: 750 mmtable width: 320 mmback stop - adjustable: 5,0-550 mmtotal power requirement: 3 kWweight of the machine ca.: 1600 kgEquipment:- manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range- 1x long side stop- 3x support arms- Free-moving foot switch- Sheet holding device for thin sheet blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3020 mmplate thickness: 5 mmdistance between columns: 3020 mmControl: Simatec OP7 stroke: 450 mmback stop - adjustable: 1000 mmwork height max.: 900 mmtotal power requirement: 22 kWweight of the machine ca.: 9000 kgdimensions of the machine ca.: 4200 x 1600/2900 x 2000 mmFeatures:- Motorized backstop, 1000 mm- Motorized upper crossbar adjustment- Motorized lower crossbar adjustment- Side protection- Foot switch- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Largeur de la feuille : 3000 mm Épaisseur de la plaque : 4 mm Hauteur maximale : 900 mm : 450 mm Puissance totale requise : 5,5 kW-poids de la machine environ : 4800 kg Dimensions de la machine : 4250 x 1500 x 1850 mm Équipement : - réglage électrique de l’angle de flexion - réglage électrique de la poutre supérieure - interrupteur au pied - instructions d’utilisation Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Largeur de la feuille : 3240 mm Épaisseur de la plaque : 2,00 mm Distance entre les colonnes : mm Besoins totaux en puissance : kPoids de la machine environ : 3,00 tDimensions de la machine environ : mFonctionnement de pliage manuel et automatique possibleAngle de flexion ajustable via potentiomètreHauteur et épaisseur du matériau de la poutre supérieure sélectionnables via des commutateurs DIP. Plier le rail et la machine en excellent état. Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
round bar steel: 34 mmsquare edge steel: 30 x 30 mmL-beam: 100 x 10 mmflat steel: 100 x 14...160 x 11 mmblade length: 175 mmT-beam: 100 x 10 mmnotching: l + T material: 10 mmhole punhing press: pressure: 45 tthroat: 305 mmtotal power requirement: 3 kWweight of the machine ca.: 1,2 tdimensions of the machine ca.: 1,4 x 0,8 x 1,5 m 5-fold combinated profile steel shear incl. flat steel shear profile steel shear bar steel shear notcher hole punch 2 foot switches contact limit stop various punching saddles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 6.5 mmthickness at Niro-steel: 5.0 mmangle adjustable from - to: 30 - 140 Gradno. of strokes: ca. 50 Hub/mintable:: 950 x 1030 mmblade length: 220 x 220 mmtotal power requirement: 4.0 kWweight: 800 kgrange L-W-H: 1100 x 950 x 1280 mm current new price approx. 20.000 euros good condition () special price on requestEquipment:- electro-hydraulic notching machine- multi-function machine with 2x work stations 1x notching, 1x unit for radius rounding including radius punching tools- manual angle adjustment 30 - 140 degrees 2x handwheels for angle adjustment- large / stable work table- 2x new angle stop, adjustable- automatic cutting gap adjustment- 1x freely movable foot switch- connection cable + 16A plug- cutting performance: 6.5 mm to 60° ST 5.0 mm to 60° VA 4.0 mm to 30° ST 3.0 mm to 30° VAThe data for this ad was created with ModulMWS - the software solution of LogoTe ...
Largeur de la feuille : 2040 mm Épaisseur de la plaque : 3,00 mm Distance entre les colonnes : mm Besoins en puissance totale : kPoids de la machine environ : 2,30 tDimensions de la machine environ : mOpération de flexion manuelle et automatique possibleAngle de flexion ajustable via potentiomètreHauteur et épaisseur du matériau de la mâchoire supérieure sélectionnables via interrupteurs DIPPauge manuel avec doigts ressortsLes données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
round bar steel: 45 mmsquare edge steel: 45 mmL-beam: 12 mm: 40 flat steel: 450x15 mmL-beam 90°: 152x152x13 mm: 45 mmsquare edge steel: 45 mm: 12 mmweight of the machine ca.: 2323 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table width: 6000 mmtable length: 2000 mmburner heads: 1 Equipment:- Plasma source Kjellberg Hi Focus 161i- suction unit- CompressorTechnical dataKjellberg Hi Focus 161i plasma cutter:Cutting current at 100 % ED 10 - 160 AMarking current 5 - 25 ACutting range 0.5 - 50 mmPiercing up to 30 mmDimensions (L x W x H) 985 x 570 x 1140 mmMass 206 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Poids max. : 20 diamètre de la pièce : 1500 - 3500 mm, diamètre du tambour : 250 x 100 mm, alimentation : 100 - 1400 mm/min, puissance totale requise : 0,75 kW. de la machine, environ : 2,5 tDimensions (LxLxH) : 2,5 x 1,5 x 1,5 mPied à rouleaux - Auto-alignement - Rotation avant/arrière - Nouveau système de contrôle - Pédale - Dispositif d’arrêt d’urgence Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Largeur de la feuille : 3050 mm Épaisseur de la plaque : 4 mm, poids de la machine environ : 6,500 kg Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Épaisseur de la plaque : 1,7 mmroll Diamètre : 50 mm Dimensions (L/P/H) : 1600 x 600 x 1500 mm Poids de la machine environ : 400 kg Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
pressure: tplate thickness: mmno. of strokes: Hub/mintotal power requirement: kWweight of the machine ca.: trequired space: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Épaisseur de la plaque : 4 mm Angle de coupe Ajustement : 30-120 Hauteur de la table : 900 mm : 407 Poids de la machine environ : 760 kg Dimensions de la machine environ : 1300x1000x1150 mm Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Largeur de travail maximale : 1000 mm Épaisseur du matériau utilisable : 0,5 - 50 mm Puissance totale : 82 A Consommation totale de courant : 44,5 kW Classe d’isolation : IP 42 Vitesse d’avance à variation infinie : 0-4 m/min Réglage de l’épaisseur du matériau : elektrisch Réglage des outils : elektrisch Longueur : 3100 mm Largeur : 2100 mm Hauteur : 2000 mm Poids de la machine : 3800 kg
Largeur de la feuille : 4200 mm Épaisseur de la plaque : 14 mm Pré-pliage : 10 mm de roulement supérieur : 340 mm diamètre de rouleau inférieur : 310 mm Vitesse : - m/minContrôle : Davi CNC Puissance totale requise : - kWweight de la machine environ : 11 tDimensions de la machine environ : 6,5 x 1,75 x 1,65 m - Contrôle DAVI CNC - pré-pliage - Entraînement hydraulique à 4 rouleaux - Diamètre du rouleau latéral : 230 mm Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
sheet width: 3100 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 3120 mmdown holder: 14 Stückcutting angle: 1°5 no. of strokes: 14 Hub/mincontrol: ENC 100 table width: 500 mmwork height max.: 880 mmoil volume: 170 ltr.total power requirement: 11.0 KWweight: 5550 kgrange L-W-H: 3750 x 1950 x 1650 mm Machine was used for ALU processing no heavy sheet metal processing good condition (!) new price ~ 32.000 Euro----------------------------------------------------Swing cut guillotine shear with fixed cutting angle with DURMA ENC 100 NC control unit manual cutting gap adjustment from the front----------------------------------------------------Equipment:- electro-hydraulic guillotine shears swing cut- with DURMA ENC 100 NC control unit Backgauge preselection - X axis Number of pieces (in automatic mode) Control panel, front left Retraction from backgauge on/ ...
x-travel: 4216,0 mmy-travel: 2007,0 mmz-travel: 305,0 mmcontrol: CNC table-size: 4902,0 x 2134,0 mmmax. workpiece weight: 1465 kg / m²machine weight ab.: 2500 kgtotal power requirement: 30 kWdimensions of the machine ca.: 5486,0 x 3708,0 mmThe compact waterjet cutting system in bridge design consists of a torsion-resistanttorsion-resistant steel construction, which is coated with a special durable anti-corrosion coating.coating. Both the two X-axes and the particularly high Y-axis are based on theY-axis are based on the maintenance-free design specially developed by OMAX for the special requirements of a waterjet cutting system.specially developed by OMAX for the special requirements of a waterjet cutting system.Equipment: - Motorized Z-axis - Water level control - Abrasive system with AFS 1000 abrasive conveyor system - High-pressure system with special stainless steel high-pressure pi ...
tube diameter: 42.0 x 3.0 STAHL mmtube diameter: 30.0 x 2.0 EDELST mmbending angle max.: 180 °bending radius max.: 100 mmbending speed: 2.0 U/min.Control: NC voltage: 400 Vtotal power requirement: 0.55 kWweight of the machine ca.: 115 kg Current new price approx. 4.200 Euro Very good condition / with machine baseDescription:- NC electro-motor tube bending machine - mandrelless up to 50 programs can be stored- Automatically returns to the starting position- Maximum bending capacity for 42 x 3.0 mm steel tubes- Excellent bending quality with very tight bending radii (from 2x tube diameter). and bending angles between 0° and 180°- Easy operation- High accuracy and reliability- Quick tool change (within seconds)- Easy to transport- Includes machine baseThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tube diameter: 60.3 x 4.5 mm STtube diameter: 60.3 x 5.4 mm ALUtube diameter: 2 x 3.91 mm GASbar material - diameter: 35.0 mmrevolutions per minute: 2.0 U/minbending radius min.: 10.0 mmbending radius max.: 270 mmexternal diameter: min. 5.0 mmexternal diameter: min. 1/8 Zollvoltage: 230 Vtotal power requirement: 1.5 kWweight: 76.0 kgrange L-W-H: 302 x 243 x 674 mmEquipment:- mandrel-less tube bending machine- Model M = ELECTRO-HYDRAULIC SINGLE-PHASE- high performance and compact design- completely hydraulic machine- bends 210° without the need to catch up- no electronic control- Ercolina patent n. 102017000142179- control of the bending angle via adjustable angle scale- mobile machine base BENDING SEGMENT AVAILABLE AT AN EXTRA CHARGE The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
chamfer lenght: 0900 mmplate thickness: mmdistance between columns: 900 mmpressure: 20 tcolumn arm: 230 mmstroke length max.: 150 mmtravel -x axis: 350 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 6.0 mm STpre-bending: 4.0 mm STdiameter of upper rolls: 200 mmside roll diameter: 165 mmdiameter of lower rolls: 190 mmbending speed: ca. 5.0 m/minControl: DIGI oil volume: 80.0 Litervoltage: 380 Vtotal power requirement: 6.0 kWweight: 6000 kgrange L-W-H: 5250 x 1500 x 1400 mm very good condition () Current new price approx. 80,000 euros Special price on requestFeatures:- Robust electro-hydraulic 4-roll bending machine 4-roll concept offers a wide range of bending and rounding options- MG swivel control panel Operation - control of all rolls and machine axes Digital position display Manual operation via joysticks- Two central rolls are driven directly by hydraulic motors- Conical rolling possible via inclined position of the rolls- Parallelism of the side rollers via torsion shafts- Bending on both sides- Diameters of up to 1.1 times the upper roller ...
table length: 3048 mmtable width: 1524 mmburner heads: 1 stroke: 270 mmspeed: 100 m/mindimensions: 8900 x 2260 x 2220 mmweight of the machine ca.: 7.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Pression de travail : 300 barres Puissance totale requise : / kWpoids de la machine environ : 1 tDimensions de la machine environ : m Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
pression : - tstroke : - mm-table-taille : - mm-puissance totale requise : - kWweight de la machine environ : 1,5 tDimensions de la machine ca. : - m : ja Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
sheet width: 3100 mmplate thickness: 13.0 mmthickness at Niro-steel: 8.0 mmdown holder: 14 Stückno. of strokes: max. 11 Hub/mincutting angle: 1°15 work height max.: 770 mmcolumn arm: ? mmoil volume: 300 ltr.control: konv. total power requirement: 15.0 kWweight: 11800 kgrange L-W-H: 4255 x 2250 x 2400 mmFeatures:- Robust electro-hydraulic swing pruning shears- Operation, swivels to the front left- Electro-motorized backgauge on recirculating ball screws Movement by push-button (forwards backwards) including ELGO digital position indicator- Manual quick cutting gap adjustment by eccentric (right side stand)- Machine stand with overhang- 1x long side stop, with mm scale- 2x front support arms, with mm scale- Ball rollers in the front support table- Hinged front finger guard- 1x free-moving foot switch- Rear safety device (protective grille)- 2x front emergency stop button- Operating instr ...
pressure: 135 tchamfer lenght: 3050 mmdistance between columns: 2550 mmdayligth: 320 - 560 mmstroke: 240 mmworking feed: 10.0 mm/secreturn speed: 150 mm/seccolumn arm: 400 mmwork height max.: 1050 mmcontrol: DNC 1200 PS/B operating pressure: max. 297 barcompressed air: 4.5 - 6.0 barconnected load: 15.0 kWoil volume: 250 ltr.weight: 11500 kgrange L-W-H: 5240 x 2400 x 2900 mm good/well-Maintained conditions used in Aluminum processing- in checked conditions - machine Video -https://www.youtube.com/watch?v=z-Bxibk_8uEFeatures:- CNC Electro-Hydraulic Press Brake- CYBELEC CNC Control Model DNC 1200 PS/B Swiveling Control Panel, Front Right Numerical Programming Tool & Program Library- CNC Controlled Axes: Y1 + Y2 + X + R + CNC Crowning- CNC Electro-Motorized Backgauge (X-Axis) with 3x Manually Adjustable Backgauge Fingers (Z-Axis) Maximum Travel Speed: 250 mm/sec- CNC electro-motorized height ...
