Fabricant:
(Catégorie: 107)
sheet width: 3060 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 3100 mmdown holder: 16 Stückno. of strokes: max. 10 - 15 Hub/minoil volume: 160 ltr.cutting angle: 1.6 °back stop - adjustable: 6.0 - 750 mmControl: ELGO P9521 total power requirement: 18.5 kWweight: 6300 kgrange L-W-H: 3900 x 2300 x 1630 mmFeatures:- Robust electro-hydraulic swing beam shear- ELGO digital display model P9521, for electric backgauge Backgauge travel X = 750 mm Backgauge-free ball screw drive Travel speed 100 mm/s- 1x stable side stop With T-slot, flip-stop, and millimeter scale- 2x stable front support arms- Electric cutting length limiter Cutting length limiter to increase the stroke rate/min.- Manual cutting gap adjustment Centrally operated on the right side stand- Front support plates- Front finger/interference guard- Inching operation with push buttons on the left c ...
sheet width: 3050 mmplate thickness: 6 mmrear stop: 1000 mmcutting angle: 0,5 - 3 °down holder: 18 Stkno. of strokes: 9-17 Hub/mintotal power requirement: 7,5 kWdimensions of the machine ca.: 3800 x 2000 x 1600 mmweight: 4500 kgEquipment:- electric backgauge- electric cutting angle adjustment- manual cutting gap adjustment- SP 9 control unit- Safety guard behind the machine incl. light barrier- front finger guard- 1x side stop- operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 6 mmrear stop: 1000 mmcutting angle: 1,2 °down holder: 14 Stkno. of strokes: 18 Hub/minoil volume: 150 ltotal power requirement: 11 kWdimensions of the machine ca.: 3900 x 1900 x 1600 mmweight: 5500 kgEquipment:- Hydraulic swing cut shears- ELGO control system- Electric backgauge 1000 mm- Manual cutting gap adjustment- Cutting length limitation- Ball rollers in the table- 2x front support arms- 1x front side stop with scale- Front finger guard, hinged- Rear safety device (protective grille + light barrier)- Foot switch- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mmplate thickness: 10 mmnumber of rolls: 21 Stückroll diameter: 80 mmband speed: 12 m/minstraightening cross-section: 5700 mm²Control: total power requirement: 60 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width - max.: 3035 mmplate thickness: 4.0 mm STplate thickness: 2.5 mm VAplate thickness: 6.0 mm ALUnumber of strokes - loaded: 20 Hübe/mincutting angle: 1.7 °work height max.: 900 mmControl: ELGO total power requirement: 8.5 kWweight of the machine ca.: 4400 kgrange L-W-H: 3416 x 2250 x 1760 mmEquipment:- robust NC electro-hydraulic guillotine shears- NC electro-motorized backgauge with ELGO control unit TYPE 85- Manual cutting gap adjustment- front support table incl. recessed grips- 1x stable side stop, with scale and tilting cam- 3x stable front support arms- 1x freely movable foot switch- front finger guard- Rear metal slide- EMERGENCY OFF button at the front- Operating instructions (PDF)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 80.0 tchamfer lenght: 2570 mmdistance between columns: 2125 mmcolumn arm: 420 mmtable width: 60.0 mmajustment speed: 100 mm/secworking feed: 10.0 mm/secreturn speed: 100 mm/secstroke: 200 mmdayligth: 470 mmtable height: 960 mmNumber of working hours: ~ 33.100 hoil volume: 90.0 ltotal power requirement: 9.0 KWweight of the machine ca.: 5750 kg.range L-W-H: 3630 x 2450 x 2550 mmEquipment:- AMADA CNC control, model OPERATEUR II Manual control for fine adjustment of the axes- CNC control OPERATEUR 2 in 8 axes (X1 X2,Y1 Y2,R1 R2,Z1 Z2)- CNC-controlled backgauge adjustment (X1 X2)- CNC-controlled vertical adjustment of the fence fingers (R1 R2)- CNC-controlled adjustment of the stop fingers left-right (Z1 Z2)- Swivel operation, front left- 1x freely movable foot switch- Top tool holder with top wedge crowning (AMADA system)- Rear safety guard (safety grid)- Side safety guard (safety ...
sheet width: 2070 mmplate thickness: 25 mmpre-bending: 18 diameter of upper rolls: 320 mmside roll diameter: 260 mmdiameter of lower rolls: 320 mm: 26 kW: 8100 kg: 4700 x 2000 x 2200 mmFeatures:- Hydraulic side roller adjustment- Conical bending device- 2 driven rollers- Hardened rollers- Hydraulic folding bearing- Mobile control panel- Foot switch- Safety device- CE markThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Diamètre du tube : 6 - 42 mm, résistance de la paroi : 3 mm, rayon de courbure minimum : 180 mm, rayon de flexion max. : 5 mm, puissance totale requise : 1,5 kW, poids de la machine, environ : 0,8 t, dimensions de la machine environ : mÉquipement : Unité de scie, unité d’encochage, unité d’ébavurage pour bords internes et externes, unité d’évasement / fonction d’évasement (cou / expansion) Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Pression : 100 Tthroat : 620 mmCourse : 0-100 mm, diamètre en feuille : 40 pouces 20 mmNo. Nombre de courses : 49 Moye/minContrôle : consommation totale de puissance : 15 kW-poids de la machine environ : 3,500 kgLes données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Largeur de la feuille : 2500 mm Épaisseur de la plaque : 3,0 mm Distance entre les colonnes : 2550 mm Angle de coupe vrai ajustable : - butée arrière - réglable : max. 510 mm Réglage de l’écart de coupe : - mm Puissance totale requise : kW de la machine environ : 1,8 tDimensions : 3,3 x 1,4 x 1,8 m Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
sheet width: 1000 mmplate thickness: 3,0 mmdistance between columns: 1050 mmdiameter of upper rolls: 90 mmtotal power requirement: 1,1 KWweight of the machine ca.: 0,47 tdimensions of the machine ca.: 1,7 x 0,8 x 1,35 mmSheet metal bending machine with custom dimensions:- Capacity 1050 x 3.0 mm- Digital display- Hardened rollers- Conical bending- Swiveling top roller- Brake motor- Safety device: Emergency stop cord- Documentation in English- 400VThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions de coupe max. : 600 x 1000 mm. Épaisseur de la plaque : max. 3 mm. Angle de coupe : 1,5 butée latérale réglable électriquement : 0 - 1010 mm. Butée arrière réglable électriquement : 0 - 610 mmNo. Nombre de courses : 60 Moyeu/min Puissance totale requise : 14 kW-poids de la machine environ : 8,7 dimensions de la machine L x Côté Étendue x Hauteur : 2,5 x 2,18 x 2,3 m Accessoires : dispositif d’empilement de tôle sur rails Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
sheet width: 1350 mmplate thickness: 4.0 mmthickness at Niro-steel: 2.0 mmno. of strokes: max. 35 Hub/mincutting angle: 2.0 Gradtable height: 945 mmdistance between columns: 1361 mmControl: CIDAN / SIEMENS engine output: 5.5 kWweight of the machine ca.: 1400 kgrange L-W-H: 2200 x 2000 x 1550 mmFeatures:- robust / motorized swing cut guillotine shears- unbreakable and torsion-free welded steel construction- compact and clear machine construction- NC electro-motorized backgauge, with digital display Target / actual value stop value input stepless adjustment over the entire travel range- 1x hold-down bar- 1x material side stop- recessed grips in the front support table- Manual cutting gap adjustment from the front- Rear sheet holding device for thin sheets- 1x freely movable foot switch- Operating instructions (PDF)The data for this ad was created with ModulMWS - the software solution of Lo ...
sheet width: 3355 mmplate thickness: 63,5 mmroll diameter: 686 mmvoltage: 400 Vtotal power requirement: 150 HPweight of the machine ca.: 95 tdimensions of the machine ca.: 62 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2520 mmplate thickness: 2.50 mm STthickness at Niro-steel: 1.50 mmupper clamping bar adjustment: 160 mmadjustment speed: 100 mm/secAdjustment folding beam: 80.0 mmBending speed: ca. 120 Grad/seccompressed air: 6.0 barwork height max.: 869 mmcontrol: POS 2000 voltage: 400 Vtotal power requirement: 7.2 kWweight: 3430 kg Current new price ~ 100.000 euros From a maintenance workshop With very good equipment ()Equipment:- CNC electric motor-driven universal swivel bending machine High-precision mechanics with modern control technology For individual and series production Robust high-speed machine with high axis speeds Torsion-free welded construction - Rotatable upper beam / as automatic tool change system With 2x tool stations (sharp and goose foot bending rail) Reduces set-up and idle times Eliminates time-consuming tool changes and adjustments- SCHRÖDER CNC control model POS ...
punching force max.: 50 tthroat: 510 mmstroke: 32 mmstroke - stepless adjustable: 10 - 32 mmno. of strokes: 35 bei 10 mm Hub/minWorking height: 1070 mmdaylight: 350 mmtable width: 255 mmdimensions: ca. 1080 x 650 x 1680 mmmaterial layer: 630 X 535 weight: ca. 1400 kgScraper, height-adjustable and removable, with interchangeable plateHydraulic low-pressure finder for foot switch operationTwo-stage foot switch and electrical controlsIntegrated hydraulic unitWith punching saddle for dies no. 3 and 4, up to Ø 39.5 mmQuick-change device for punches 3 and 6 up to Ø 39.5 mmPeddinghaus blue serieswith material support table no. 513, dimensions 630 x 535 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 4000 mmplate thickness: 30 / 35 mmpre-bending: 30 mmdiameter of upper rolls: 570 mmside roll diameter: 450 mmdiameter of lower rolls: 540 mmbending speed: 4 m/minmin. bending diameter: 650 mmtotal power requirement: 60 kWweight of the machine ca.: 52 todimensions of the machine ca.: - mThe machine was overhauled in 2022Equipment:- Hydraulic 4-roller round bending machine- Roll material: 61 MnCrMo 43- Driven rolls: 2 Top-and bottom roll-- Drive: over 2 hydro motors direct flanged-- Adjustment speed bottom roll: 0-200 mm/min-- Adjustment speed side rolls: 0-700 mm/min- Speed compensation between top-and bottom roll: automatic- Operation of the tilting bearing: hydraulic- Tilting of the top roll: hydraulic- Bearing block: hydraulic- Indicator device of roll position: digitalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mmplate thickness: 4,5 mmpre-bending: 4,0 mmmin. dia.: 210 mmroll diameter: 140 mmweight of the machine ca.: 1530 kgdimensions of the machine ca.: 3220x1200x900 mmStandard features:- Central rollers via electric motor, planetary reduction gear andGear drive driven- Swivel top roller- Main engine with brake device- Conical bending device- Mobile controller and foot pedal- CE mark / Declaration of ConformityAdditional equipment:- motorized rear roller adjustment- Digital display for back roller- induction hardened rollsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Largeur du matériau : 0400 mmbobine Poids : 1,50 Épaisseur du matériau : MMNOMB. Des rouleaux de redressement : 9 diamètres des rouleaux Environ : 30 mm Plage d’expansion Environ : 460 - 530 mmCoil Extérieur - Diamètre environ : 1500 mm Puissance totale requise : kPoids de la machine environ : Dimensions de la machine environ : m Les données pour cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
: : : Consommation totale de puissance : kWweight de la machine ca. : tdimensions de la machine ca. : mLes données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
working width: 1500 mmworkpiece width - max.: 0,5 - 50 mmdimensions: 3300 x 1500 x 1800 mmfeed stepless: 0-4 m/mintotal power requirement: 20,4 kWweight of the machine ca.: 2800 kgThe SBM-L G1S2 grinding and deburring machines were developed for double-sided deburring and edge rounding of workpieces in a single operation. LISSMAC machines are used for deburring sheet metal and processing sheet metal parts, laser parts, and stamped parts.The L series is equipped with three units on the top and bottom . Workpieces made of stainless steel, steel, aluminum or non-ferrous metal can be processed on the top, bottom or both sides. Processing sheet metal on both sides and rounding edges in a single operation saves up to 60% in time. It is also possible to easily connect automation solutions or integrate the machine into production lines. The machine design ensures ergonomic working and a pleasant ...
working width: 1000 mmworkpiece width - max.: 0,5 - 50 mmsandingbelt width: -- mmweight of the machine ca.: 2,5 tWith the SBM-L 1000 G1S2, which works in the dry process, in alternating operationSteel, stainless steel and aluminum can be machined. She deburrs and roundsthe edges on the outer and inner contours of punched, laser, fine plasma orwater jet cut workpieces with a thickness of up to 50 mmon both sides in just one operation. Two sanding units, 1 each on the top and bottom, remove spatterand slight burrs on outside and inside edges of sheet metal. A total of four sanding belts, 2 each on the top and bottomUnderside, process the sheets on both sides at the same time. hereAll edges are softened or rounded, depending on the tool settings. Machining on both sides saves time-consuming turning of the workpieces andedit twice. All pairs of aggregates can be switched on/off separately de ...
sheet width: 3050 mmplate thickness: 6 mmdistance between columns: 3460 mmtable height: 800 mm0: 220 barcutting angle adjustment: 0,5x3 °down holder: 18 back stop - adjustable: 750 mmfront stop - adjustable: 1000 mmmain drive: 7,5 kWoil volume: 300 ltotal power requirement: 7,5 kWweight of the machine ca.: 4,5 tdimensions of the machine ca.: 3,7x2,0x1,8 mcutting angle adjustment manuallyblade gap adjustment manuallyangle stopThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Largeur de la feuille : 2500 mm Épaisseur de la plaque : 3 mm Distance entre les colonnes : 2540 mmback stop - réglable : 550 mm Puissance totale requise : 5 kWweight de la machine environ : 2,7 tDimensions de la machine environ : 3,2 x 2,5x 1,9 m Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
plate thickness: 4 mmblade length: 220 mmpressure: 0 tweight of the machine ca.: 1,5 tdimensions of the machine ca.: 1,6 x 1,7 x 1,6 mtotal power requirement: 2,5 kWCombined notching machine with a fixed 90° angle and an adjustablerectangular notching unit variable up to 200mm length x fixed 100mm width.There are 2 manually adjustable stops with a digital display.Axle length X900mm / Y300mmThere is no stamp holder / punch / hold-down device for this.These parts can be purchased from Boschert.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Épaisseur de la plaque : 3-4 mm Pression : 0 t Longueur de coupe : 220 mm Hauteur de la table : 900 mm Quantité d’huile : 35 l Dimensions de la table : 950 x 790 mm Puissance totale requise : 4 kW-poids de la machine environ : 0,95 tDimensions de la machine environ : 1,0 x 0,86 x 1,2 mRéglage automatique de l’angle de commutation 30-140 Réglage automatique des espaces de coupe Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
: 220 kNsheet thickness - max.: 8 mmtravel -x axis: 2500 mmtravel -y axis: 1250 mm: 90 m/min: 60 m/min: 108 m/min: 360 °/secpunch diameter: 76,2 mmworkpiece weight: 150 kg: 0,01 mm bzw. 0,01° : 15 Stücktool changing time: 1,5 - 6,5 secweight of the machine ca.: 11.050 kgdimensions: 6400 x 5800 x 2100 mmWorking hours: 30.430 hThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Largeur de la feuille : 2500 mm longueur de la plaque : 1250 mm épaisseur de la plaque : 8 mm Capacité de poinçage : 220 kNumber d’heures de travail : 51,658 h Besoins totaux en puissance : kW-poids de la machine environ : 11,050 kg Les données de cette publicité ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.
Dérouleur Dérouleur avec bras : 1,5 tonne Largeur du matériau : 350 mm Diamètre extérieur de la bobine : 1,200 mm Plage d’expansion : 370 - 430 mm Vitesse : 0 - 20 m / min Niveleur / Redresseur Largeur du matériau : 250 mm Nombre de rouleaux de nivellement : 9 pièces. Diamètre des rouleaux de nivellement : 30 mm Épaisseur du matériau : 0,5 - 6 mm Section transversale : 1,200 mm Vitesse d’alimentation : 20 m / min Puissance requise : 18 kW
sheet width: 3200 mmplate thickness: 3.0 mm STthickness at Niro-steel: 2.0 mmOpening width / upper beam: 300 mmspeed: OW 40.0 mm/secBending beam adjustment: 80.0 mmspeed: BW 90.0 Grad/secwork height max.: 900 mmcontrol: MULTIBEND 5000 back stop - adjustable: 10 - 1550 mmaccuracy +/-: 0.1 mmair pressure: 5.0 barNumber of working hours: ca. 1.000 htotal power requirement: 2x 4.0 kWvoltage: 400 Vweight: 4400 kgrange L-W-H: 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours () good condition () Special price on request- in checked condition - machine video -https://www.youtube.com/watch?v=VP6emx4HTYM! Maximum flexibility when bending cassettes, boxes and profiles! High flexibility in bending part design! High productivity and throughput! Easy to useEquipment:- motorized universal swivel bending machine RAS 73.30 high-precision mechanics with ...
