sous-catégories
(troisième niveau de catégorie)
Fabricant:
(Catégorie: 706)
Overview This Robopac Helix 4 EVO is an automatic rotating-arm stretch wrapper for pallet loads, built in 2021. It has less than 500 operating hours and is technically close to new. The arm carries the pre-stretch carriage around the stationary pallet, so the load itself is never turned - the configuration for unstable, fragile or heavy loads at high output. Throughput reaches 82 pallets per hour at 11 wraps and 1,000 mm load height, 73 at 15 wraps and 1,600 mm, and 64 at 19 wraps and 2,000 mm. The machine has an integrated roller conveyor and was built as a stand-alone unit, loaded and unloaded by forklift. Technical data Manufacturer: Robopac Model: Helix 4 EVO Year of manufacture: 2021 Machine type: automatic rotating-arm stretch wrapper (pallet winder) Operating hours: less than 500 h Capacity: 82 pallets/h (11 wraps, H 1,000 mm), 73 pallets/h (15 wraps, H 1,600 mm), 64 pallets/h (19 ...
Overview This Robopac Genesis Futura HS is an automatic rotating-ring stretch wrapper for pallet loads, built in 2023. It has less than 500 operating hours and is technically close to new. The rotating ring carries the pre-stretch carriage around the stationary pallet, which allows high throughput without moving the load: up to 92 pallets per hour at 13 wraps and 1,000 mm load height, 77 pallets per hour at 17 wraps and 1,600 mm, 70 pallets per hour at 19 wraps and 2,000 mm. The machine is delivered as a stand-alone unit with integrated roller conveyor and is prepared for line integration over Ethernet TCP/IP. Technical data Manufacturer: Robopac Model: Genesis Futura HS Year of manufacture: 2023 Machine type: automatic rotating-ring stretch wrapper (pallet winder) Operating hours: less than 500 h Capacity: up to 92 pallets/h (13 wraps, H 1,000 mm), 77 pallets/h (17 wraps, H 1,600 mm), 7 ...
Overview This KHS Innoclean is a single-end bottle washer for returnable glass bottles, built in 2007. It cleans and de-labels empty bottles before filling. The bottles are pushed into the cells of the carrier baskets, run on heavy roller chains through a pre-soak, two pre-warming baths, the main caustic soak with under- and over-caustic label flushing and three water spray zones, and are handed back onto the bottle conveyor at the discharge. Nineteen bottles are handled across the machine width in 4,275 cells. Output is adjustable between 2,800 and 14,500 bottles per hour; the machine was configured for 13,200 bottles per hour of 0.75 l glass bottles at 18.7 minutes total dwell time and 10.8 minutes of caustic contact. In 2022 KHS modernised drive and operator station. The machine runs the Triple-i-Drive with individual servo-controlled geared motors and is operated from a capacitive mu ...
The Mac Ewans Centrifugal pump is a pump for use in sanitary applications. Previous used in a Casein plant. Motor: 7,5 kW - 380/415 V - 50 Hz - 1.455 rpm - 14,6/13,4 A. Diameter of the impellor: 180 mm. Connections on the inlet: 3. Connections on the outlet: 2,5. Estimated capacity: ± 30.000 ltr/h., macewans.co.nz/, Type of Machine: Centrifugal pump, Stock Number: 1454, Diameter of the impellor: 180 mm, Motor: 7,5 kW - 380/415 V - 50 Hz - 1.455 rpm - 14,6/13,4 A, Estimated capacity: ± 30 m3/h
The APV Puma 2.2.9 Centrifugal Pump is a pump used in hygienic applications. Designed for Cleaning-in-Place (CIP). Can be used in hygienic applications like dairy, food, beverage and personal care industries that require gentle product treatment and reliable operation. Motor: ± 7,5 kW - 380 V - 50 Hz (no nametag on the motor). Diameter of the impellor: 191 mm (7,5). Pump casing: 9. Connections on the inlet: 2. Connections on the outlet: 2. Capacity with the current motor: ± 35 m3/h at a differential pressure of ± 2 Bar., Type of Machine: Sanitary centrifugal pump, Stock Number: 1656, Diameter of the impellor: 191 mm, Motor: ± 7,5 kW - 380 V - 50 Hz (no nametag on the motor), Current estimated capacity: ± 35 m3/h at a differential pressure of ± 2 Bar
Suitable for 0.7l-VdF bottles, capacity: 3000bottles/h, running direction: right to left, the packing head is equipped with 12 long-life packing tulips, the machine was used in low-volume operation, is very well maintained and has low operating hours, an on-site inspection is possible.
Throughput: 2000bottles/h, format parts: 1l and 0.75l bottles, an on-site inspection is possible.
Throughput: 2000-4000bottles/h, number of rows: 12, the machine is steam-heated and fully functional, an on-site inspection is possible.
Throughput: 5000bottles/h, format parts: 0.75l bottles, an on-site inspection is possible.
LEIBINGER TRANSVASA 12/6 EK – monobloc counter-pressure bottle emptying / transfer machine for carbonated beverages in glass bottlesIDENTIFICATION- Manufacturer: LEIBINGER- Model: TRANSVASA 12/6 EK- Year of manufacture: 2017- Serial/order number: 472447- Previous application: ciderFUNCTION AND OUTPUT- 12 emptying valves- Counter-pressure emptying with long-tube technology- 6 decapping stations- Direction of operation: clockwise- Nominal output: 2,500 bottles/h for 0.75 l bottles- Adjustable range: 560–2,800 bottles/h- Designed for carbonated beverages, e.g. traditionally produced cider- Automatic removal and collection of pierced bottle closures- Integrated through conveyorPRODUCT AND UTILITY DATA- Maximum product temperature: 20 °C- Compressed air: 6 bar, connection R 1/2- CO? product pressure: 8 bar, gas connection R 1/2- Product outlet: DN 40- Gas discharge: DN 40- Buffer tank: 1 ...
Overview This Gronemeyer VFA is a vertical conveyor for glass bottles, built in April 2020 by Gronemeyer Maschinenfabrik GmbH & Co. (Höxter, Germany). It raises bottles between the levels of a filling line and works with two synchronously running endless chains whose carrier elements take the bottle from both sides, so the container is guided upright over the whole climb. The nominal capacity is 45,500 bottles per hour at a conveying speed of approximately 60 m/min. The conveying width is set by hand crank across a range of 20 to 150 mm, so a format change needs no tooling. The machine is enclosed in transparent guarding, has service doors with safety switches, an automatic central lubrication system and a pneumatic chain tensioning station. It is currently being dismantled and can be inspected at BEVMAQs warehouse in Germany from early September 2026. Technical data Manufacturer: Grone ...
Overview This KHS Innopas P II SG 30-200 is a tunnel pasteurizer for bottled beverages in glass bottles, built in 1996 by KHS (Klöckner Holstein Seitz, Germany). With a treatment area of 113.5 m² across 8 treatment zones (3 of them recuperative), it pasteurizes at approx. 24,000 - 25,000 bottles per hour depending on bottle format, at a maximum pasteurization temperature of 75 °C. For 0.7 l glass bottles the total treatment time is approx. 48.6 minutes (21.2 min heating, 12.3 min pasteurization, 15.0 min cooling) at approx. 5 pasteurization units. The main control is a Siemens SIMATIC S5 PLC; the pasteurization unit setting (temperature diagram) was later upgraded to a Siemens S7 with touch panel. Danfoss frequency drives are fitted. The machine ran at a German mineral water bottling plant until mid-2024 and is now completely dismantled and professionally stored, with the conveyor bel ...
Rinçage Triblock 32 + 32 Bouchon de bouchon + 8 Bouchons à vis en plastique Adapté aux boissons non gazeuses en PET
Séparateur de conteneurs adapté pour le PET et les cartons
Overview Complete filling line for non-returnable glass bottles with an output of approx. 16,000 bottles/h at 0.75 L and approx. 20,000 bottles/h at 0.33 L. The heart of the line is a KOSME BARIFILL RFC 50-60-10 VKP rinser-filler-capper block built in 2013. New glass is fed by a Krones sweep-off depalletizer from 2020; downstream, the line comprises Krones CHECKMAT cap control, a KHS INNOKET cold-glue labelling machine with camera-based label orientation, a Krones WRAPAPAC wrap-around packer and a GEA Procomac OPERA palletizing system with Robopac stretch wrapper and Logopack pallet labelling. An attractive mid-range line for water, soft drinks, beer, cider and other glass-bottle applications. Technical data Year of manufacture: mainly 2013 Capacity: approx. 16,000 bph at 0.75 L / approx. 20,000 bph at 0.33 L Application: filling and packaging of non-returnable glass bottles Filling syst ...
ARTICLE N° : Velo-400-20-MC - Utilisation d’un filtre à levure avec 19 plaques filtrantes pour sceller le bord, longueur totale d’environ 2 300 mm - Surface totale de filtration : 5,3 m² et teneur totale en sous de vent : 66 litres. - avec de nouveaux tissus de filtre monofilament (n° 1001.6439) - avec pompe à membrane 1 800 litres/h. - avec plateau goutte-à-goutte - Avec une nouvelle pompe hydraulique manuelle - Interrupteur de pression, connexion air comprimé, soupape de sécurité - Filetage de vin selon les souhaits - Garantie fonctionnelle d’un an
Overview This high-pressure air compressor was manufactured in 2003 by the Belgian company Ateliers François (AF). The CE68 ASG model is designed to supply compressed air at 40 bar, specifically for PET bottle blowing applications. The compressor is still installed and electrically connected in Germany and is available immediately. Technical data Free air delivery: 2,100 m³/h (35 m³/min) Operating pressure: 40 bar Design pressure (PS): 42 bar Speed: 480 rpm Shaft absorbed power: 355 kW Voltage: 400 V Year of manufacture: 2003 Application: PET bottle blowing Scope of delivery 1 × High-pressure compressor 40 bar CE68 ASG 1 × Refrigeration dryer 1 × Electrical control cabinet Condition Still installed and electrically connected Available for inspection on site Availability Immediately available.
Gamme complète de remplissage de bouteilles PET pour boissons gazeuses fabricant : SIPA / PROCOMAC année de fabrication : 2009 Localisation : Allemagne disponibilité : À partir d’octobre 2026 La ligne est actuellement en service et peut être inspectée pendant la production. Détails techniques : Capacité : Environ. 12 500 bouteilles par heure Tailles des bouteilles : 500 ml, 750 ml, 1 500 ml Finition du manche : PCO 28 / 1881 750 ml supplémentaires avec chapeau sportif (PCO 1881) Composé de : 1. Souffleuse SIPA SFR 8 avec 8 cavités y compris le système d’alimentation par exécution incluant le refroidisseur mais sans dispositif de déchargement préalable et sans compresseur haute pression 2. Convoyeur d’air GEA Procomac 3. Tribloc GEA Procomac 50 / 70 / 12 avec 50 stations de rinçage, 70 vannes de remplissage et 12 culasses Bouchon à vis ...
Overview This SIPA SFR 8 is an 8-cavity rotary stretch-blow moulding machine for PET bottles, built in 2009 by SIPA (Italy). It processes PET preforms into bottles of 0.5 l, 0.75 l and 1.5 l at an output of up to 12,400 bottles per hour. The blowing station is fully enclosed by safety guarding with viewing windows, and the machine is operated from a machine-mounted touchscreen control panel. It has been running as the stretch-blow moulder of a PET bottling line for mineral water and soft drinks, and is still installed and under power, so it can be inspected in production. Technical data Manufacturer: SIPA (Italy) Model: SFR 8 Year of manufacture: 2009 Machine type: rotary stretch-blow moulder for PET bottles Number of cavities: 8 Output: up to 12,400 bottles/hour Bottle formats: 0.5 l, 0.75 l and 1.5 l Neck finish: 28 mm / 1881 (short neck) Electrical connection: 400 V, three-phase Total ...
Overview This Ortmann + Herbst Hansa B 100/20 is a rotary filler-capper monoblock for glass bottles, originally built in 1994 and completely refurbished in Germany in 2013. It combines 100 filling valves with a 20-head aluminium screw capper in a single machine and reaches up to 30,000 bottles per hour with 750 ml glass bottles. The 2013 refurbishment covered the machines controls, drive and guarding: a new electrical system with Siemens S7 control and a Siemens SIMATIC MP377 12 touch panel, a new main bearing, and a new safety housing around the machine. Two change part sets are included, for 250 ml and 750 ml bottles. The machine is still installed and under power, so it can be inspected in its production environment. Technical data Manufacturer: Ortmann + Herbst Model: Hansa B 100/20 Year of manufacture: 1994, completely refurbished 2013 Machine type: rotary filler with screw capper, ...
Caractéristiques : Volume 3150 L Matériel n° V2A Surpression maximale de fonctionnement 0,99 bar Hauteur totale 3000 mm Diamètre 1300 mm Diamètre extérieur 1400 mm Surface à l’intérieur de 2B = Masse IIIC Surface extérieure à 2B = Masse IIIC Température de travail : 20 °C Longueur du cylindre : 2000 mm Description : Terre arable : Fond de clapet Buse filetée DN40 centrale Bose filetée côté DN40 Clapet anti-retour Cylindre : Bouche d’égout ovale 440 x 340 Échantillon de prise DN15 Crochets en échelle Ligne CIP inclinée vers le bas DN40 avec vanne à disque et manomètre Buse de soudure filetée DN25 avec vanne à disque Bobine de refroidissement avec entrée et sortie de 3/4 de pouce Manche à bride de couvercle aveugle DN125 Dessous du babais : Fond de battants / arrière courbé tuyau de drainage rés ...
Caractéristiques : Volume 2750 L Matériel n° V2A Surpression maximale de fonctionnement 2 bars Hauteur totale 2850 mm Diamètre 1540 mm Diamètre extérieur 1550 mm Surface à l’intérieur de 2B = Masse IIIC Surface extérieure en verre sablée par le sablage Description : Terre arable : Fond de battants / arrière courbé Diamètre du couvercle de bride : 450 mm Conduit de trop-plein de connexion DN40 sortant latéralement Buse de soudure filetée DN65 avec vanne à disque Buse de soudure filetée DN65 2 x douilles filetées à souder DN25 Cylindre : Crochets en échelle câble CIP tiré vers le bas DN40 4 bobine de refroidissement de 70 mm de large Capteur de température Fischer Douille à souder DN15 Dessous du babais : Base conique avec chemise de refroidissement de 35 cm de hauteur Buse de soudure filetée latérale ...
Overview This M+F KEG-Technik MICROMAT M 1/1-F KeyKeg is a semi-automatic filling machine for one-way KeyKegs, built in 2011 by M+F KEG-Technik (Bottrop, Germany) and used in a Belgian brewery. The machine fills 20 l and 30 l KeyKegs at 50-60 kegs per hour. It became redundant when the brewery switched its production from one-way KeyKegs back to returnable stainless steel kegs. It has already been dismantled, is in storage and can be inspected on request. Technical data Manufacturer: M+F KEG-Technik Model: MICROMAT M 1/1-F KeyKeg Year of manufacture: 2011 Machine type: semi-automatic KeyKEG filling machine Capacity: 50-60 KeyKegs per hour Container formats: 20 l and 30 l KeyKEG Fitting type: KeyKEG fitting Connection voltage: 230/400 V, 50 Hz Equipment EC Declaration of Conformity (Machinery Directive 2006/42/EC) Technical documentation Condition Used. The machine has already been disman ...
Overview This SMI TF350 is a tray packing machine for PET bottles, built in 2009 by SMI (Italy). It forms cardboard trays from flat blanks and packs PET bottles at an output of 45 to 50 packs per minute. Tray forming is carried out with an integrated Nordson ProBlue 4 hot-melt adhesive unit. The machine is fully enclosed by a safety guard with large viewing panels and hinged access doors, and is operated from a control cabinet mounted on the machine frame. It has been running as the tray packer of a PET bottling line for mineral water and soft drinks, and is still installed and under power, so it can be inspected in production. Technical data Manufacturer: SMI (Italy) Model: TF350 Year of manufacture: 2009 Machine type: tray packer for PET bottles Output: 45 - 50 packs/min Adhesive system: Nordson ProBlue 4 hot-melt unit Packaging material: flat cardboard blanks Guarding: full safety enc ...
Overview This SMI SK 450 T is a shrink packer for PET bottles, built in 2009 by SMI (Italy). It collates bottles into pack formations, wraps them in shrink film and shrinks the film in the integrated heating tunnel, at an output of up to 45 packs per minute. It handles 0.5 l bottles in 3x3, 0.75 l bottles in 2x3 and 1.5 l bottles in 2x3 formats. The wrapping section is fully enclosed by safety guarding with viewing windows, and the machine is operated from a machine-mounted touchscreen control panel. It has been running as the shrink packer of a PET bottling line for mineral water and soft drinks, and is still installed and under power, so it can be inspected in production. Contrary to the pictures and videos, please note that the tray forming unit is no longer available. This unit has been removed and is no longer installed in the machine/line. Technical data Manufacturer: SMI (Italy) M ...
On behalf of our client, we are selling this SIG Asbofill ABF (Aseptic Bottle Filler), 10-Lane, PET bottle filling machine which is designed for the aseptic filling of liquid, non-carbonated, microbiologically sensitive high- and low acid products into prefabricated plastic bottles. The client bought a new and bigger aseptic filling machine for extension of his production capacities. This machine is recently dismantled and located in the warehouse of the dairy factory., The machine was used the last 8 years to fill protein shakes and milk related drinks (cold fill) at the current factory. Before it was used for fruit juices. Sterility Assurance Level (SAL) of 6-log reduction. Shell of life of the current products: 9 months. Capacity: 12.000 bottles/h @ 1.000 ml, 10.000 bottles/h @ till 1.500 ml and 8.000 bottles/h @ till 2.000 ml. Filling accurancy: ± 2 ml (filling volume 1.000 ml). Bot ...
Cleaning in Place” (CIP) system, consisting of the following components: - 400-liter stainless steel tank serving as a hydrostatic circulation tank - 7.5-kW feed pump (Packo) for pumping 25 m³/h against 4.1 bar - 4.0 kW return pump (Packo) for pumping 25 m³/h against 2.0 bar - Shell-and-tube heat exchanger (Weinbrenner) for heating a flow rate of 25 m³/h from 55 °C to 75 °C with 790 kW - 4-channel chemical dosing system (ProMinent) for lye, acid, disinfectant, and additive - Temperature measurement - Conductivity measurement (E+H) - Inductive flow meter (E+H) - Control cabinet with touchscreen display - Various piping and valves, Additional title: Cleaning system for cleaning pressurised tank cellars, Volume circulation tank: 400 l, Length: 2,5 m, Width: 3,0 m, Height: 2,9 m, Operation / Control: Simatic S7, Material: contact surfaces from stainless steel, Position: on stainless s ...
CIP system with a total of 7 tanks, including: - 1 tank with a capacity of 60 hl as a reserve water tank - 5 tanks, each with a capacity of 30 hl (manufactured in 1992), for acid, reserve water, Desi, and 2 x lye - 1 tank with a capacity of 20 hl (manufactured in 1992) for fresh water Additional system components: - 3 centrifugal pumps - Heat exchanger - Conductivity measurement - Various piping and valves, Additional title: 7-tank CIP system with pumps and heat exchanger, Volume stacked water tank: 6000 l, Volume 5 x tanks for cleaning solutions: 3000 l, Volume fresh water tank: 2000 l, Material: stainless steel, Position: vertical vessels each on 3 feet, Features: 7 x CIP tanks (comprising 1 x 60 hl, 5 x 30 hl and 1 x 20 hl); 3 x centrifugal pumps; heat exchanger; conductivity measurement; various pipework and valves
Vertical outdoor tank with insulation and cladding, most recently used as a storage tank for hot water., Additional title: vertical outdoor stainless steel tank with insulation, Gross volume: 80000 l, Material: Stainless steel 1.4571 (AISI 316Ti), Position: standing on a concrete plinth, Base construction: cylindrical tank with a dished dome, Features: Insulation; cladding; lifting eyes; cleaning pipe
vertical stainless steel tanks with insulation and cladding, most recently used as storage tanks for degassed water, Additional title: vertical, insulated stainless steel tanks, Gross volume each: 14340 l, Material: stainless steel, Position: each standing on 3 feet, Base construction: cylindrical frames, Features: outlet pipe with manual valve; overflow pipe ladder bracket; manhole
