子类目
(三级类目)
生产厂家:
(品类: 106)
压力：160 行程：810 毫米 进气：360 毫米 - 稳定尺寸：900 x 630 毫米 RAM 尺寸：750 x 450 毫米 日轻度：800 毫米 活塞直径：400/360 毫米 冲程速度：200 毫米/秒 总功率需求：17千瓦 机器重量约：7吨 本广告数据使用 ModulMWS - LogoTech oHG 的软件解决方案创建
pressure: 120/15 tdistance between columns: 860 mmstroke: 170 mmtable-size: 860 x 600 mmdayligth: 350 mmmax. distance table - ram: 520 mmram head dimension: 860 x 600 mmhole in the table: 200 x 140 mmtable height over floor: 850 mmtotal power requirement: 25 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 2,3 x 1,7 x 3,4 mMaximum ram pressure: 120 kNMaximum pull-out pressure: 15 kNSick light curtainSafety distance: 180 mmMaximum overrun: 15 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 040 tchamfer lenght: 1600 mmdistance between columns: 1100 mmstroke of upper beam: 100 mmthroat: 195 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sec: 180 barwork height max.: 840 mmtable width: 110 mmdayligth: 295 mmControl: ATL 550 total power requirement: 5.5 kWweight: 2500 kgrange L-W-H: 2100 x 1200 x 1800 mmEquipment:- NC-controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control - model ATL 550 Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1 Y2 axis) Possibility of programming different programs Memory capacity max. 200 programs - max. 400 blocks Swivel control panel, left front- Electro-motorized backgauge (X axis) with 2x stop fingers, manually adjustable (R Z axis)- Tool holder system A - with top wedge crowning- Split insert/bending tools- Lateral safety guards- rear safety guard- 1x freely movable double foot swit ...
压力：100 柱间距：400毫米，行程：20 - 140毫米，表面积：900 x 710 毫米，表面积：560 x 450 毫米，调节：80毫米，日光度：470毫米。行程数：70 轴心/最小总功率需求：10.5千瓦 机器重量约9 机器尺寸 长 x 宽 x 高：1.98 x 1.60 x 3.10 米 本广告数据由LogoTech oHG的软件解决方案ModulMWS创建
压力：200 稳定长度：2200毫米 平板宽度：1550毫米 日光：2200！！MMRAM回流能力：6,000公斤 tableload容量：10,000千/分钟 总功率需求：？机器重量约25-30千瓦，尺寸约30，尺寸 约4 7 7 米，包装尺寸：约13.4 x 3 x 3 米。本广告数据由LogoTech oHG的软件解决方案ModulMWS创建
pressure: 40.0 tchamfer lenght: 1600 mmdistance between columns: 1100 mmstroke of upper beam: 100 mmthroat: 195 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sec: 180 barwork height max.: 840 mmtable width: 110 mmdayligth: 295 mmControl: ATL 550 total power requirement: 5.5 kWweight: 2500 kgrange L-W-H: 2100 x 1200 x 1800 mmEquipment:- NC-controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control - model ATL 550 Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1 Y2 axis) Possibility of programming different programs Memory capacity max. 200 programs - max. 400 blocks Swivel control panel, left front- Electro-motorized backgauge (X axis) with 2x stop fingers, manually adjustable (R Z axis)- Tool holder system A - with top wedge crowning- Split insert/bending tools- Lateral safety guards- rear safety guard- 1x freely movable double foot swi ...
压力：倒切 长度：毫米 柱间距离：毫米 总功率需求：千瓦 机器重量 约：所需空间：百万 本广告数据使用 ModulMWS 创建 —— LogoTech oHG 的软件解决方案
pressure: 220 tchamfer lenght: 3200 mmdistance between columns: 2700 mmControl: Cybelec CybTouch 12 throat: 400 mmstroke: 220 mmdayligth: 480 mm: 140 mm/sbending speed: 0-10 mm/s: 110 mm/stotal power requirement: 18,5 kWdimensions: 3600 x 2000 x 2900 mmweight: 11.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 130 tchamfer lenght: 3200 mmdistance between columns: 2700 mmControl: Cybelec CybTouch 12 throat: 400 mmstroke: 200 mmdayligth: 480 mm: 200 mm/sbending speed: 0-10 mm/s: 120 mm/stotal power requirement: 7,5 kWdimensions: 3600 x 1800 x 2700 mmweight: 8.200 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tthroat: 250 mmstroke: 400 mmdayligth: 500 mmtable surface area: 800 x 500 mmControl: Siemens S7 hole in the table: 0 mmtable height over floor: 500 mmram surface: 800 x 500 mmworking feed: 10 mm/secspeed down: 110 mm/sekspeed up: 160 mm/sekpower requirement: 11,0 kWweight of the machine ca.: 5,5 tdimensions: 1,9 x 1,7 x 2,9 mSingle-column press with- Hardened and chrome-plated cylinder- Main cylinder diameter 220 mm- Auxiliary cylinder diameter 50 mm- Bosch Rextroth pump, valves, and filters- Hydraulic overload valve- Hydraulic proportional valve- Siemens touchscreen control panel with remote maintenance access Settings for stroke, pressure, speed, and dwell time- Category 4 sensors and photoelectric sensor- Two-hand control panel with reset and emergency stop buttons- CE markingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tstroke: 380 mmtable surface area: 1100x424 mmdayligth: 180/750 mmdistance between columns: 1100 mmdiameter of piston: 90 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
压力：15 tthroat：- mm行程：- mm尺寸（L/W/H）：1200 x 1200 x 1700 mm，总功率需求：- kW 本广告的数据使用 ModulMWS——LogoTech oHG 的软件解决方案创建
pressure: 150 tthroat: 400 mmstroke: 400 mmdayligth: 600 mmtable surface area: 1000 x 600 mmControl: Siemens S7 hole in the table: 0 mmtable height over floor: mmram surface: 1000 x 600 mmworking feed: 5 - 15 mm/secspeed down: 130 mm/sekspeed up: 180 mm/sekpower requirement: 18 kWweight of the machine ca.: 12,0 tdimensions: 2,4 x 1,9 x 3,5 mSingle-column press with- Hardened and chrome-plated cylinder- Main cylinder diameter 270 mm- Auxiliary cylinder diameter 70 mm- Bosch Rextroth pump, valves, and filters- Hydraulic overload valve- Hydraulic proportional valve- Siemens touchscreen control panel with remote maintenance access Settings for stroke, pressure, speed, and dwell time- Category 4 sensors and photoelectric sensor- Two-hand control panel with reset and emergency stop buttons- CE markingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 330 tchamfer lenght: 6100 mmdistance between columns: 5600 mmControl: Cybelec VisiTouch 24 stroke: 300 mmdayligth: 500 mm: 160 mm/sbending speed: 0-9 mm/stotal power requirement: 32 kWweight of the machine ca.: 36.000 kgdimensions: 6970 x 2300 x 4150 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 250 tchamfer lenght: 3550 mmdistance between columns: 3000 mmControl: Cybelelc DNC 1200 total power requirement: kWweight of the machine ca.: 18.500 kgdimensions of the machine ca.: 4300x2750x3750 mmAccessories:- 2-hand foot switch- Lasersafe Fisseler- Hydraulic tool clamping at top and bottom- Die shift- Hydraulic crowning- Support arms- Cybelec DNC 1200 control- 1 set of upper and lower tools- Controlled axes y1, y2, x, r, z1, z2, inclined stop- Protective grilleThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 225 tchamfer lenght: 2050 mmdistance between columns: 1550 mmcontrol: CYBELEC DNC 1200 PS Eco stroke: 550 mmtable height: 700 mmthroat: 405 mmdistance between table / ram: 320-870 mmcolumn arm: 405 mmweight of the machine ca.: 14.000 kgAccessories / equipment:- controlled axes: Y1 - Y2 - X - R- Z1 and Z2 can be moved manually- Lasersafe angle measurement- Pneumatically adjustable support table- pneumatic upper and lower tool clamping- 2-hand foot control- manual crowningThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 125 tchamfer lenght: 3000 mmdistance between columns: 3100 mmControl: Cybelec VisiTouch 24 stroke: 300 mmdayligth: 500 mm: 200 mm/sbending speed: 0-12 mm/stotal power requirement: 15 kWweight of the machine ca.: 11.500 kgdimensions: 4080 x 3110 x 1800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 330 tchamfer lenght: 3100 mmdistance between columns: 2600 mmControl: Cybelec VisiTouch 24 throat: 500 mmdayligth: 500 mmstroke: 300 mm: 165 mm/sbending speed: 0 - 10 mm/stotal power requirement: 32 kWweight of the machine ca.: 18.500 kgdimensions: 3900 x 1970 x 3520 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 330 tchamfer lenght: 4100 mmdistance between columns: 3600 mmControl: Cybelec VisiTouch 24 stroke: 300 mmArm length: 500 mmdayligth: 500 mm: 165 mm/sbending speed: 0 - 10 mm/stotal power requirement: 32 kWweight of the machine ca.: 21.000 kgdimensions: 4850 x 2300 x 3520 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 2000 tdistance between columns: - mmstroke: 140 mmstrokes per minute: 15-50 H/mintable surface area: 1000 x 1100 mmdimension of ram: - mmweight of tools max.: - kgShut Height: 650 mmdistance table - lower edge of ram: - mmram adjustment: 25 mmmain drive: 30 kWtotal power requirement: - kWweight of the machine ca.: - tdimensions of the machine ca.: - mmProduction of stamped and formed parts, mechanical drive with toggle lever driveThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 220 tchamfer lenght: 4100 mmdistance between columns: 3600 mmControl: Cybelec CybTouch 12 throat: 400 mmstroke: 220 mmdayligth: 480 mm: 140 mm/sbending speed: 0-10 mm/s: 110 mm/stotal power requirement: 18,5 kWdimensions: 4500x2000x2900 mmweight: 13.000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 150 tstroke: 300 mmtable surface area: 1070 x 290 mmcolumn travel between the guideways: 1070 mmajustment speed: 9.0 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secengine output: 11.0 kWweight of the machine ca.: 2070 kg.range L-W-H: 2200 x 1200 x 2550 mm Display machine from 2023 With only approximately 2 operating hours Like new condition Special price upon requestFurnishing:- Robust electro-hydraulic workshop press, with adjustable cylinder- Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more.- Robust welded steel construction for high demands- Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket- 1x set of V-block prism supports- Manometer for pressure display- simply constructed hand control with: 1x delivery speed 1x working speed 1x re ...
pressure: 30.0 tstroke: 200 mmtable surface area: 775 x 190 mmcolumn travel between the guideways: 775 mmajustment speed: 7.5 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secengine output: 3.0 kWweight of the machine ca.: 400 kg.dimensions of the machine ca.: 1.500 x 700 x 1.800 mmFeatures:- Robust electro-hydraulic workshop press with fixed cylinder- Ideal for aligning axles, shafts, etc.,. but also for pressing in and out bolts, bearings, bushings, and much more.- Robust welded steel construction for heavy-duty use- Table height adjustment via piston rod Includes round steel chain and 2 locking pins Piston rod with metric mount- 1 set of V-block prism supports- Pressure gauge for pressure display- Simple manual control with: 1 feed speed 1 working speed 1 retraction speed- Piston can be stopped in any position- Fixed hydraulic tank mounted on the side- Operating instructionsThe ...
pressure: 60.0 tstroke: 250 mmtable surface area: 1040 x 370 (315) mmcolumn travel between the guideways: 1040 mmajustment speed: 8.0 mm/secworking feed: 4.0 mm/secreturn speed: 10.0 mm/secengine output: 4.0 kWweight of the machine ca.: 800 kg.dimensions of the machine ca.: 1.700 x 700 x 2.100 mmFeatures:- Robust electro-hydraulic workshop press with fixed cylinder- Ideal for aligning axles, shafts, etc.,but also for pressing in and out bolts, bearings, bushings, and much more.- Robust welded steel construction for heavy-duty use- Table height adjustment via piston rod Includes round steel chain and 2 locking pins Piston rod with metric mount- 1 set of V-block prism supports- Pressure gauge for pressure display- Simple manual control with: 1 feed speed 1 working speed 1 retraction speed- Piston can be stopped in any position- Fixed hydraulic tank mounted on the side- Operating instructio ...
pressure: 100 tstroke: 300 mmtable surface area: 1070 x 315 mmcolumn travel between the guideways: 1070 mmajustment speed: 8.0 mm/secworking feed: 5.0 mm/secreturn speed: 10.0 mm/secoil volume: 90.0 lengine output: 5.5 kWweight of the machine ca.: 1870 kg.dimensions of the machine ca.: 2050 x 1000 x 2200 mmFurnishing:- Robust electro-hydraulic workshop press, with adjustable cylinder- Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more.- Robust welded steel construction for high demands- Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket- 1x set of V-block prism supports- Manometer for pressure display- simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed- Piston can be stopped in any position- Hydraulic tank mounted on t ...
chamfer lenght: 0900 mmplate thickness: mmdistance between columns: 900 mmpressure: 20 tcolumn arm: 230 mmstroke length max.: 150 mmtravel -x axis: 350 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 120 tchamfer lenght: 3050 mmdistance between columns: 2550 mmstroke of upper beam: 155 mmthroat: 350 mmajustment speed: 100 mm/secworking feed: 9.0 mm/secreturn speed: 77.0 mm/secControl: P 40 work height max.: 878 mmtable width: 104 mmoil volume: 150 ltotal power requirement: 11.0 kWweight: 7550 kgrange L-W-H: 3550 x 2150 x 2600 mmEquipment:- NC electro-hydraulic press brakes- with NEW ELGO NC control unit P40 New price approx. 4.000 Euro Control / movement of the backgauge - X axis (target/actual input) Control / movement of the depth setting - Y axes (target/actual input) Inching mode for X axis Y axes also possible- Swivel operation, front left- NC controlled axes : Y1 Y2 X- NC electro-motorized backgauge (X axis) with 2x manually adjustable stop fingers including lateral and height adjustment (Z R axis)- 1x branded set of upper tools (split)- 1x branded Multi-V bottom die ...
pressure: 180 tchamfer lenght: 3100 mmdistance between columns: 2550 mmthroat: 310 mmstroke: 200 mmajustment speed: 80.0 mm/secworking feed: 10.0 mm/secreturn speed: 58.0 mm/secdayligth: 385 mmtable width: 240 mmwork height max.: 885 / 1050 mmoil volume: 180 ltr.total power requirement: 15.0 kWweight of the machine ca.: 9850 kg.range L-W-H: 4200 x 1750 x 2450 mm from a maintenance workshop well-maintained condition ()- in checked condition - machine video -https://www.youtube.com/watch?v=o_t9BBMsNNsEquipment:- simple, conventional electro-hydraulic press brake with torsion shaft for parallelism of the upper beam- electric back stop, with ball screws (X axis) with 4x manually adjustable stop fingers fine adjustment via handwheel at the front, with analog position display- electro-motor adjustment of the immersion depth (Y1 + Y2 axis) with digital position display- swiveling operation, mou ...
