pressure: 75 tstroke: 8-80 mmno. of strokes: 80-200 Hub/minram - range of adjustment: 70 mmtable surface area: 900x600 mmram surface: 900x470 mmhole in the table: 450x180 mmdist. between columns - front to rear: 500x350 mmdist. between pillars (front to rear): 788 mmtotal power requirement: 10 kWweight of the machine ca.: 10 tdimensions of the machine ca.: BxTxH 1600x1200x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 75 t, 80 mm, 120 1/min
压力 75 t 冲程频率 120-600 / min 板材宽度 10-300 毫米 工作台尺寸 1050 x 820 mm 推杆夹紧面积 960x820 mm 距离表 - 英式柱塞 380 mm 可调行程 - 最大 80 mm 进料长度 0-150 mm 总功率要求 20 kW 机器重量约 13 吨 进料装置，最大皮带速度 70 m/min 偏心轴，带 4 倍轴承 2 根连杆 中央润滑 包括磁力带式输送机 - 使用至 2020 年 -作说明 -手动 - 电路图
pressure: 10 tstroke: 8-40 mmno. of strokes: 120-600 Hub/minram - range of adjustment: 40 mmtable surface area: 380x240 mmram surface: 220x140 mmhole in the table: 220x110 mmtable height: 910 mmtool hole in ram: Ø 30 mmthroat: 135 mmtotal power requirement: kWweight of the machine ca.: 1,2 tdimensions of the machine ca.: BxTxH 1000x1500x2000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 30 t, 100 1/min
规格 压力 30 t 行程速率 100 – 600 mm 柱塞行程可调至 40 mm 安装高度 300 mm，带内置夹
pressure: 25 tno. of strokes: 1500 Hub/minsheet width: mmtotal power requirement: 20 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 75 t, 80 mm, 250 1/min
压力：75t 工作台： 650 x 560 mm 柱塞面积： 500 x 300 mm 行程速度：50-250行程/分钟 提升高度：8-80 mm 最大安装高度： 400 mm 侧支架之间的通道： 300 毫米 馈线： 制造商： GSW 型号： WV32/80 带宽：最大320mm 胶带厚度：最大3.5mm 滚筒直径：80mm
pressure: 25 tno. of strokes: 1500 Hub/minsheet width: mmtotal power requirement: 20 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 250 tstroke: 37 mmno. of strokes: 30-240 Hub/minram adjustment: 150 mmtable surface area: 1200x1000 mmhole in the table: 500x180 mmtool hole in ram: Ø52 mmtotal power requirement: 50 kWweight of the machine ca.: 35 tdimensions of the machine ca.: LxBxH 3700x2300x3900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
压力： 25 吨行程数： 60-300 轮毂/分钟板材宽度： 150 毫米滑枕 - 调节范围： 6-50 毫米工作台面积： 350x400 毫米滑枕表面： 250x250 毫米工作台上的孔： 130x150 毫米机器重量 CA.： 3
pressure: 125 tstroke: 10-80 mmno. of strokes: 240 Hub/minram - range of adjustment: 80 mmtable surface area: 850x600 mmram surface: 760x550 mmhole in the table: 850x130 verstellbar mmtable height: 1100 mmtool hole in ram: Ø 50 mmtotal power requirement: kWweight of the machine ca.: 13 tdimensions of the machine ca.: BxTxH: 3000x2000x3300 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 80 tstroke: 8-140 mmno. of strokes: 105 Hub/minram - range of adjustment: 100 mmtable surface area: 900x625 mmram surface: 600x280 mmhole in the table: Ø 150 mmtable height: 1000 mmtool hole in ram: Ø 40 mm: 490 mmweight of the machine ca.: 7 tdimensions of the machine ca.: BxTxH 1800x2200x2600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 315 tstroke: 40-200 mmno. of strokes: 20-100 Hub/minram - range of adjustment: 120 mmram surface: 2000x1100 mmtable surface area: 2000x1200 mmhole in the table: 1700x250 mm: 500 mmcolumn travel -side: 820x650 mmtotal power requirement: 45 kWweight of the machine ca.: 44 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
压力： 20 吨行程： 8-38 毫米行程数： 100-1800 轮毂/分钟工作台表面积： 400x400 毫米工作台通过数： 380x80 毫米工作台高度： 1000 毫米机器重量： 4 吨机器尺寸 直径： BxTxH 1600x1600x3100mm m
pressure: 63 tstroke: 10-80 mmno. of strokes: 65-400 Hub/minram - range of adjustment: 80 mmtable surface area: 1030x550 mmram surface: 920x450 mmhole in the table: 700x200 mm: 420 mmweight of the machine ca.: 10 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 tstroke: 10-130 mmno. of strokes: 30-90 Hub/minthroat: 330 mmram - range of adjustment: 100 mmtable surface area: 950x660 mmram surface: 540x440 mmhole in the table: Ø 230 mmtable height: 1000 mmtool hole in ram: Ø 50 mmtotal power requirement: 7,5 kWweight of the machine ca.: 7 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
压力： 63 吨行程： 6-60 毫米行程数： 90-550 轮毂/分钟： 300 毫米工作台表面积： 780x600 毫米滑枕表面： 807x460 毫米滑枕中的工具孔： 40 毫米滑枕 - 调节范围： 80 毫米总功率要求： 15 kW机器重量 约： 8 吨机器尺寸 约： BxTxH 2900x2000x3000
pressure: 63 tstroke: 4-60 mmno. of strokes: 85-500 Hub/minram - range of adjustment: 80 mm: 320 mmtable surface area: 750x600 mmram surface: 750x600 mmtotal power requirement: 31 kWweight of the machine ca.: 8,2 tdimensions of the machine ca.: BxTxH 2900x1900x2900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 75 tstroke: 8-80 mmno. of strokes: 80-200 Hub/minram - range of adjustment: 70 mmtable surface area: 900x600 mmram surface: 900x470 mmhole in the table: 450x180 mmdist. between columns - front to rear: 500x350 mmdist. between pillars (front to rear): 788 mmtotal power requirement: 10 kWweight of the machine ca.: 10 tdimensions of the machine ca.: BxTxH 1600x1200x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 250 tstroke: 37 mmno. of strokes: 30-240 Hub/minram adjustment: 150 mmtable surface area: 1200x1000 mmhole in the table: 500x180 mmtool hole in ram: Ø52 mmtotal power requirement: 50 kWweight of the machine ca.: 35 tdimensions of the machine ca.: LxBxH 3700x2300x3900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
压力：100 t冲程速率：30-70冲程/分钟柱塞行程 - 最大：130 mm柱塞调整：100 mm工作台面：950x630 mmRam面积：630x600 mm投影：340 mm安装高度：480 mm卷筒：GSW 总功率要求：kW机器重量约：8.9 t空间要求约为：mD技术数据是制造商或操作员的规格 因此对我们无约束力。我们保留进行事先销售的权 ，我们的业务和销售条款和条件仅适用。关于我们 超过400台自有机器在仓库超过8500平方米的存储区域， 起重机容量70吨以上超过1000件配件为您的车间如果您 出售机器生产线或您的公司，请与我们联系。该广 的数据是使用模态MWS创建的 - 标识科技oHG的机器管理
