oerlikon 용접 기계 사용 판매를 위해

Controls: Heidenhain TNC 360 (1992) Table size: 1,000 x 1,000 mm Table size with extension: 1,345 x 1,000 mm Table load max.: 2,000 kg Distance between the s distance Spindle to table top: 0 - 1,100 mm Travel distances: X 1400 mm Y 900 mm Z 850 mm W 370 mm spindle holder: MK 5 spindle drive power: 6 kW spindle speeds: 30 - 1,500 rpm Drilling spindle diameter: 82 mm drill diameter: 2 - 70 mm Drilling tools Diameter: 17 - 450 mm Drilling capacity to full ST60: 45 mm Drilling capacity to full GG: 70 mm Zubehoer: drills; tools; usw. machine was rebuilt in 1992 and !; Very good

Control: Heidenhain TNC 360 (1992) Table size: 1000 x 1000 mm Table size with front extension: 1345 x 1000 mm Table load max.: 2000 kg Distance spindle centre to column min/max.: 270 ~ 1270 mm Distance spindle nose to table min/max.: 0 - 1100 mm Distance between the upright columns: 1855 mm Table longitudinal travel : 1400 mm Boring ram carriage cross travel: 900 mm Crossrail vertical travel: 850 mm Boring spindle travel: 370 mm Spindle motor rating: 6 KW Spindle speed range: 30 - 1500 rpm Boring spindle diameter: 82 mm Spindle taper: MK 5 Borer diameter: 2 - 70 mm Boring tool diameter: 17 - 450 mm Boring diameter in solid ST 60: 45 mm Boring diameter in solid Cast iron: 70 mm Equipped with: Tooling; Accessories Machine overhauled and retrofitted in 1992 !; Very good

Machine type MIG/MAG welding system Make OERLIKON Type Citomag 506 W Connection voltage 3 x 400 volts Adjustment range 30 - 500 Ampere Switching time 60 % ED at 500 amps 100% ED at 420 amps Current setting infinitely variable Cooling transformer by built-in fan Cooling burner water-cooled Design of mobile industrial plant with separate DV case Wire feed gearbox gearboxed 4-roll gearbox Protection up to a maximum of 300 A = 32 A over 300 A = 63 A Dimensions L x W x H 1,050 x 630 x 1,050 mm Weight 237 kg Age approx. 20 years Condition workshop tested, good, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece welding torch, 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqm 1 piece pressure reducer argon with 2 pressure gauges 1 piece spare parts box kpl. Equipped 1 piece user manual  ...

Various spare parts for Oerlikon lathes.

Specifications: - Total payload driven + running unit 40000 kg - Payload per container device 20000 kg - Workpiece diameter approx. 500 - 3500 mm - Center distance of the support rollers adjustable via trapezoidal thread spindle - Roll diameter 500 mm - Roll width 150 mm - driven single-sided drive - infinitely adjustable rotation speed - Handheld remote control for re- and li.-run - Drive 400 V - Both units are built on rail chassis - Space requirements Unit approx. W 3800 x H 1150 x D 1350 mm - Platzb. with running unit approx. W 3600 x H 1150 x D 1350 mm - Weight applied. Unit approx. 2500 kg - Weight with running unit approx. 1800 kg

Specifications: - TIG – DC + electrode welding - Welding current infinitely adjustable for TIG welding of 5 A-10.0 V to 150 A - 22 V 35% ED 100 A 100% ED - Connection 220 V / 50 Hz 15 A - with: - 2 stroke 4 stroke - function - HF ignition - Welding current descent setting - Gas pre-flow regulation - Gas afterflow regulation - Hose package 4.5 lfm, lightweight design - Ground cable - Pressure reducer - Space requirement approx. W 200 x H 300 x D 500 mm - Weight approx. 10 kg - Transport trolley with gas cylinder slot W 550 x H 900 x D 560 mm - Weight transort van approx. 10 kg

offer 22629 TIG welding machine - air-cooled equal-alternating current system, mobile - for welding all weldable metals - e.g. stainless steel, steel, aluminium, brass, etc. - Welding current TIG infinitely adjustable from 20 A to 270 A 35% ED - A 100% ED - Connection 400 V - with: - Digital welding current indicator - Frequency control of the arc - HF ignition - Pulse device - Hose package 5 m -Reducer - Ground cable - Carriage - Space requirement approx. W 550 x H 1150 / 1300 x D 950 mm - Weight approx. 180 kg

Arc welder Manufacturer: Oerlikon Type: Minicito

Stick electrodes 4.0 x 450 -Type: Special -Weight per package: 5.3 kg

Stick electrodes 5.0 x 450 -Type: Fincord Price: per package -Number: 4 packages available -Weight per package: 5.5 kg

wire electrode, welding wire, welding wire -Cored wire: Fluxofil: 36 -Diameter: 1.6mm -Dimensions: O 300/100 mm -Weight complete: 15.6 kg

Stick electrodes 4.0 x 350 -Type: Overcord -Price: per package -Number: 5 packages available -Weight per package: 5 kg

Stick electrodes 4.0 x 350 -Type: Fincord S -Price: per package -Number: 6 packages available -Weight per package: 4.4 kg

Machine type: MIG/MAG welding system Make Oerlikon Type Minicito 304 Connection voltage 3 x 400 Volt Adjustment range 35 – 300 amps Duty cycle 35% ED at 300 amps 60% ED at 230 amps 100% ED at 180 amps Current setting: 14 switching levels Cooling transformer by built-in fan Cooling burner gas-cooled Design of mobile compact system Wire feeder toothed 4-roller gearbox Fuse protection 16 amps Dimensions L x W x H 950 x 400 x 820 mm Weight 80 kg Age approx. 15 years Condition workshop-tested, good, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece welding torch 3 mtr. long 1 piece of ground cable 1 piece pressure reducer 1 roll of welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece of hand shield 1 piece of protective glass 10 DIN 1 piece of glass attachment white 1 spare  ...

Stick electrodes 4.0 x 350 -Type: Fincord -Price: per package -Number: 4 packages available -Weight per package: 4.3 kg

wire electrode, welding wire, welding wire -Cored wire: Fluxofil 31 -Diameter: 1.6mm -Dimensions: O 300/100 mm -Weight complete: 15 kg

wire electrode, welding wire, welding wire -Cored wire: Carbofil 1 -Diameter: 1.6mm -Price: per roll - Quantity: 2 pieces -Dimensions: O 300/100 mm -Weight per roll: 15 kg

Stick electrodes 2.0 x 250 -Type: Fincord -Price: per package -Number: 2 packages available -Weight per package: 1.7 kg

Machine type: Submerged arc welding machine Manufacturer: Air Liquide / Oerlikon Type: CPQ170126926 / incl. power source, turn-tilt device, container rotation device Year of Make: 2017 Condition: used / very good, few operating hours Offer will only be sent if a complete imprint is provided! Price VB Location Warstein , Germany Reference MV-AIR-0824 DESCRIPTION We offer you a used UP welding machine from the manufacturer Air Liquide / Oerlikon. - Starmatic 1200i AC/DC - Citowave III / 420 - Posimatic PS15 / Tilt and Tilt Device - Container turning device Weight approx. 7t More detailed dates will follow Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact detail ...

current capacity: kVA throat: mm contact pressure capacity: kp volume capacity: Punching capacity: kN punching cross-cut in cmm: stroke: mm weight of the machine ca.: 170 kg dimensions: 1200 x 900 x 1350 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1000 mm turning diameter over slide rest: 640 mm turning length: 6300 mm turning dia. in gap: 1250 mm spindle diameter: 50 mm speed: 6-925 U/min total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stick electrodes 2.0 x 350 -Type: Special -Weight per package: 3.9 kg

Stack electrode 4.0 x 350 -Type: Cromocord Kb -Weight per package: 4.8 kg

Stick electrodes 2.5 x 350 -Type: Overcord -Price: per package -Number: 5 packages available -Weight per package: 4.8 kg

Stick electrodes 3.2 x 300 -Type: CITOCHROMAX N -Price: per package -Number: 13 packages available -Weight per package: 2.9 kg

Stick electrodes 4.0 x 350 -Type: Overcord -Price: per package -Number: 6 packages available -Weight per package: 4.8 kg

Stick electrodes 5.0 x 450 -Type: Supercito E51 55 B 10 -Price: per package -Number: 13 packages available -Weight per package: 5.5 kg

Stick electrodes 4.0 x 450 -Type: Extra EY 42 53 Mn B -Price: per package -Number: 29 packages available -Weight per package: 5.4 kg

Center height: 400 mm Center width: 1250/1300 mm Circumferential Ø: over bed 440 mm Spindle bore: Spindle holder: Pick-up cone tailstock: 5 MK Spindle speeds: 11.2 - 2240 rpm Feeds: longitudinal/flat 0.1-2.8/0.05-1.4 mm/rev Thread pitches: Electrical connection: 380 V, 11 kW Space requirement: 3400 x 1400 x 1300/1700 mm Weight: approx. 2700 kg

Welding rectifier, electrode welding machine, electrode welding rectifier -Welding current: max. 220 A -Dimensions: 1200/700/H720 mm -Weight: 280 kg

Wire feed case for inert gas welding machine, inert gas device, wire feed case, wire feed device -Manufacturer: Oerlikon wire feeder, gas-cooled -Type: unfortunately without type designation -Dimensions: 640/280/H400 mm -Total weight: 19.6 kg

max. wheel diameter: 500 mm Hypoid adjustment: ±70 mm axial cross angle: 90 ° Distance Y-: 150 - 350 mm Distance Z-axis: 120 - 340 mm turning speed range - stepless: 0 - 5000 U/min max. torque on the spindle: 57 Nm Cone: 99,2 mm Pull-in force Tool clamping: 23000 N Braking torque max.: 93 Nm total connected load: 20 kVA total power requirement: 15 kW weight of the machine ca.: 6 t dimensions of the machine ca.: 2,35 x 2,24 x 2,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 400/500 mm CNC-Control: GE FANUC Series 160i-M pinion diameter - max.: 400 mm crown gear diamter max.: 500 mm x-axis: +/- 70 mm y-axis: 200 mm z-axis: 200 mm axis angle: 90 Grad speeds:: R 0 - 3000 / T 0 - 5000 1/min rated current: 30 kVA weight of the machine ca.: 6,2 t dimensions of the machine ca.: 3,2 x 2,5 x 2,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 1000 mm gear width: 630 mm max. module: 16 min. module: 1 wheel diameter with counterstay: 800 mm max. number of teeth: 999 clamping length: 1060 mm workpiece weight: 1500 kg max.helical angle: 45 ° grinding spindle drive: ca. 20 kW Control: Opal / Siemens total power requirement: 70 kW weight of the machine ca.: 17,5 t - CNC control Opal / Indramat with Siemens S5 PLC - paperbandfilter - oil mist exhauster - complete covering The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A complete plasma cutting system Oerlikon including peripheral equipment is available. 1) CNC plasma cutting system Oxytome 30, year of manufacture: 2008. 2) Plasma source Air Liquide Nertajet HP125, year of manufacture: 2008. 3) Filter unit Donaldson Torit DCE DFPRO 8-Cyclo, year of manufacture: 2008, weight: approx. 1625kg. 4) Cooling unit Air Liquide Friojet-30, year of manufacture: 2008, cooling capacity: 2kW, max. operating pressure: 29.5bar, refrigerant: R407c, weight: 80kg. Documentation available. An on-site inspection is possible.

TIG welding machine for TIG DC welds Brand: Oerlikon Citotig DTW 256; Fabr.Nr. 91762 Item Condition Little used, very well preserved, Special features inert gas, Scope of application Steel, stainless steel, non-ferrous metals For plants, machinery and steel construction, pipeline and industrial construction, Robust, versatile control and operation modes With intermediate hose package, welding hose package; Welding torches, ground cables, gas hose with pressure reducer Industrial equipment for precision welding Mains connection: 3 x 400 V /50 - 60 Hz; IP 23 Application voltage range: approx. 10.1 – 20 V DC Welding range at: 2 - 250 A With mobile frame to accommodate the machine with gas cylinder (not in the scope of the machine) Dimensions Length x width x height: 1000 x 420 x 1130 mm

Submerged arc welding device, welding accessories, forming gas welding device, longitudinal carriage, chassis, welding carriage, longitudinal carriage, welding machine, welding carriage, inert gas welding device, longitudinal seam welding system, longitudinal seam welding machine, longitudinal seam welding device, rail runner -Submerged arc welding machine without: power source -Submerged arc welding machine type: Minisaf 02 -Control box SUBARC 3 -Intermediate hose package -Equipment -Dimensions: 1200/800/H500 mm -Weight: 215 kg

Welding rectifier, electrode welding device, electrode welding machine, electrode welding rectifier, power sources -Three-phase rectifiers for: MMA DC welding -Welding power: max. 350 A -Welding cable with: electrode clamp -Ground cable -Number: 2x welding machines available -Price: per piece -Dimensions: 500/620/H835 mm -Weight: 126 kg

TIG welding machine, inverter welding machine, TIG welding machine, inverter welding machine -Manufacturer: Oerlikon, Inverter welding machine type CITISTICK 160 -Welding current range: 5-160A -Mains connection: 230V -Accessories: Welding cable with electrode clamp, ground cable -Dimensions: 430/300/H340 mm -Weight: 11 kg

z-travel: 200 mm Clamping diameter of the cutter heads: max. 550 mm Max. permissible cutter head weight: 150 kg Mounting plate diameter for cutter heads: 360 mm Mounting cone for cutter heads Nominal diameter: 500 mm weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2 x 1,5 x 2,03 m Cutter Head Set-Up- and -Measuring Machine In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in dry milling, high gear cutting quality and a long service life can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing devic ...

voltage: 110 - 230 V frequency range: 50 - 60 Hz Power connection: 0,5 kVA Dimensions (HxWxD): 1000 x 800 x 1750 mm weight: 150 kg Measuring machine for bar knives. Equipment/accessories: -Measuring tools -Clamping devices -Computer -Monitor -Printer -Cabin -Technical documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

OERLIKON cutter heads

max. wheel diameter:275 mm gear width:55 mm max. module:6,5 min. module:1,5 Face Hobbing-Continious Process Continuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surface C28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, w ...

max. wheel diameter:275 mm gear width:55 mm max. module:6,5 min. module:1,5 Face Hobbing-Continious Process Continuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surface C28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, w ...

Manufacturer: Oerlikon Model: Plasmatome 20 HPC ( without cutting table ) Year of Manufacture: 2012 Cutting Range: 2,000 mm x 6,000 mm (2 x 6 meters) Material Thickness Capacity: Up to 35 mm Cutting Method: Plasma Cutting Find more here - / Contact us at -

1 L+Z lathe Make: VDF-Oerlikon Boehringer Model; DUE 560 Year of Make: 1986 Turning diameter over bed: 570 mm Turning length: 1000 mm Speed range: 11.2 - 2240 rpm Weight of the machine: 3.8 tons. Accessories / equipment: digital display, chip protection. Conveyor belt cover, Coolant device, rapid traverse.

(side-front moving table) Nominal force: 1000 ton Slide stroke: 400 mm Continuous slide strokes per 1 min: 20 Single slide strokes per 1 min: 16 Shut height: 1060 mm Slide adjustment: 320 mm Table dimensions: 3150x1800 mm Slide dim., front-back: 1700 mm Window H 1500 x W 1900 mm Hydro pneumatic cushion in table clamping force at P = 0.42 MPa (P = 4.2 kg / cm2), kN 2000 ejection force P = 0.45 MPa (P = 4.5 kg / cm2), kN 200 Main-drive electric motor power: 132 kW DIMENSIONS: 5150x4700x11400 H floor7830 mm WEIGHT:193 ton

Table 1750 x 920 mm, fixed stroke 101 mm, see pictures and description,; All right

; in order

Capacity , ton: 800 Stroke, mm: 320 Strokes/min: 20 Shut height, mm: 900 Bed to ram adjustment stroke, mm: 320 Bed dimensions, mm: 2500x1600 Main drive motor power, kW: 75 Overall dimensions, mm: 4220x3500x8356 Weight, ton: 96,6

The nominal gain kN 4000 Slide stroke, mm 400 Frequency Slider strokes min-1, 25 The frequency of single strokes, min-1 19 Slider travel to its lowest position, where the press develops the rated force, mm 8 The distance between table and slider in its lower position at the upper adjustment position, mm 470 Size of adjustment of distance between table and slider, mm 160 The size of the table, mm 1000x1000 The size of the slide from front to back, mm 800 Width of windows in racks mm 600 Main electric motor power, kW 37.0 Air flow, m3 / stroke 0,017 Press overall dimensions, mm left to right 3470 front to back 3140 Height above floor level, mm 5940 Weight without hydro pillow kg 32600

ABB IRB 2400 M2000 robotic machining cell manufactured in 2004 in Switzerland, is equipped with an ABB IRB 2400/16 6-axis industrial robot and an ABB IRC5 controller for the control of the manipulator and peripherals. The machining station has so far been configured and used for milling of allowances after thermoforming workpieces. The high-performance milling robot has an arm with a maximum reach of 1550 mm, capable of handling workpieces weighing up to 16 kg. The industrial robot achieves the best cycle performance thanks to modern technology that automatically optimises parameters and executes the programmed path regardless of speed or operating mode, even after an emergency stop or power failure. The BaseWare OS operating system is used to fully control every aspect of the machine, ensuring the highest machining accuracy is achieved. The robotic milling station is offered with  ...

Maximum force ton-force 400 Slider stroke length mm 250 Slider stroke length to lower position mm 12 Slider strokes per minute 25 Number of single turn-on 19 Maximum distance between table and slider (in lower position of slider) mm 510 Adjustment mm 160 The sizes of a under-forginig plate mm 1000 Table overall dimensions: mm ·from front to rear 1000 ·from left to right 1000 The sizes of an aperture in a table mm 630 Slider overall dimensions mm 800 x 800 window dimensions in cheeks mm 600 Total power of electric motors kW 43,3 Press overall dimensions mm ·length 3470 ·width 3140 ·height 5940 Press weight without hydropneumatic pillow kg 31 400

Nominal effort: 630 tons Course stroke: 420 mm Number of strokes in a minute: 20 Bolster plate-to-ram adjustable stroke: 180 mm Max. distance plate-to-ram (in lower position of slider): 750 mm Slider dimensions 1000x1000 mm Table size: 1250x1250 mm Dimensions of the hole in the table 800x800mm Thickness of the sub-stamp plate 180 mm Height above floor level 600 mm Main motor power: 56 kW hydropneumatic pillow in the table Press overall dimensions: -Length: 3280 mm -Width: 3470 mm -Height: 6190 mm Press weight: 52650 kg

ARISA S-2-400-260-FD mechanical press was built in 2000 in Spain by Arisa S.A. (now Nidec Press & Automation Co. (NP&A)). The machine on offer is an excellent choice for series production of components used in the broadly defined automotive or machinery industry. It enables precise punching and stamping of metal parts. All these machining processes are performed with a high press force of up to 400 tonnes, which, combined with a highly dynamic slider, guarantees the best machining results. The ARISA S-2-400-260-FD features a robust, stress-relieved gantry design with an open side wall. This design maintains high rigidity, stable parameters and repeatability during even the most intensive operations with high press force. It is distinguished by the use of two connecting rods, a flywheel drive and an eccentric pinion gear. This solution ensures even torque transmission and smooth and pr ...

Maximum force ton-force 400 Slider stroke length mm 250 Slider stroke length to lower position mm 12 Slider strokes per minute 25 Number of single turn-on 19 Maximum distance between table and slider (in lower position of slider) mm 510 Adjustment mm 160 The sizes of a under-forginig plate mm 1000 Table overall dimensions: mm - from front to rear 1000 - from left to right 1000 The sizes of an aperture in a table mm 630 Slider overall dimensions mm 800 x 800 window dimensions in cheeks mm 600 Total power of electric motors kW 43,3 Press overall dimensions mm - length 3470 - width 3140 - height 5940 Press weight without hydropneumatic pillow kg 31 400

Nominal effort: 630 tons Course stroke: 420 mm Number of strokes in a minute: 20 Bolster plate-to-ram adjustable stroke: 180 mm Max. distance plate-to-ram (in lower position of slider): 750 mm Slider dimensions 1000x1000 mm Table size: 1250x1250 mm Dimensions of the hole in the table 800x800mm Thickness of the sub-stamp plate 180 mm Height above floor level 600 mm Main motor power: 56 kW hydropneumatic pillow in the table Press overall dimensions: -Length: 3280 mm -Width: 3470 mm -Height: 6190 mm Press weight: 52650 kg

Groove width: 3-100 mm Drawing length: 850 mm Stroke: 870 mm Table size: 780 x 430 mm Bore range: Diameter: 10-600 mm Return speed: 40 m/min Cutting speed: 0-16 m/min Total power requirement: 8 kW Machine weight approx. 1.55 t Space requirement approx. 1.8 x 2 x 2.25 m Foundation depth: can be omitted (1.07) m because the machine looks on a steel platform A number of accessories available

Capacity, ton 630 Stroke path till its position where it develops nominal capacity, mm 16 Slider stroke, mm 320 Slider strokes, spm 20 Max. distance between table and slider, mm 800 Distance adjustment between table and slider, mm 180 Table size, mm 1250 x 1250 Slider dimensions, mm 1000 x 1000 Opening in the table, mm 800 x 800 Thickness of bolster, mm 180 Cushion stroke, mm 130 Main motor power, kW 58 Machine dimensions, mm 3280 x 3470 x 6190 Machine weight, kg 55500

VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available

Maximum force of slide: T 250 Stroke of slide: mm 400 Stroke rate per min 12 Adjustability of slide: mm 120 Bed area (W x D): mm 2500x1400 Main motor power: kW 32 Max depth of extraction 100mm pressing force during the maximum depth of extraction T 100 Force holding extract unit: T 50 Height above ground: mm 5000 Weight: 66 ton

sheet width: 1550 mm plate thickness: 3 mm total power requirement: 3 kW weight of the machine ca.: 1600 kg dimensions of the machine ca.: 2.060 x 1.140 x 1.210 mm Producer: OSTAS Type: RGM 1050 x 3 YOM: new Max. Shearing Length: 1.050 mm Shearing Capacity: 3 mm Shearing Angle: 2°30 Strokes Per Minute: 35 d/d Motor Power: 3 kW Table Width: 510 mm Table Height: 820 mm Rear Gauge Distance: 500 mm Dimensions of the machine (LxWxH): 1.640 x 2.060 x 1.210 mm Weight: ca. 1.100 kg Additional information: • Manual backgauge with 500 mm stroke • Squaring arm with T-slot, stopper and ruler • Foot pedal • Front sheet holding arms • Cutting line lighting • Protection Cages optional: • Cutting unit counter • Motorised backgauge with 500 mm stroke • Backgauge with NC control • Pneumatic Sheet Support System • Optical security bar • 0-180° angle cutting The data for thi ...

Capacity: 800 tons Stroke of slider: 400 mm Number of strokes per minute 12 Adjustment of slider: 185 mm Max. daylight betwen bolster and slider SDAU: 850 mm Table area: 1250 x 1650 mm Slider dimensions 1000 x 1250 mm Main motor power: 55 kW Distance between columns 1250 mm Cushion capacity, ton 125 Cushion stroke, mm 160 Press dimensions, mm 3800 x 2800 x 6900 Weight: 77 tons

Maximum force ton-force 400 Slider stroke length mm 400 Slider strokes per minute 25 Maximum distance between table and slider (in lower position of slider) mm 470 Size of adjustment of distance between down-stamp a plate and slider mm 160 Table overall dimensions: mm ·from front to rear 1000 ·from left to right 1000 Slider overall dimensions: mm ·from front to rear 800 Main electric motor power kW 40 Press overall dimensions mm ·length 3470 ·width 3140 ·height 5940 Press weight kg 32600

ARISA S-2-630-240-120-LD mechanical press was built in 2005 in Spain by Arisa S.A. (now Nidec Press & Automation Co. (NP&A)). The machine on offer is an excellent choice for series production of components used in the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, such as precise punching and stamping of metal parts. In addition to its standard purpose, depending on the tooling and material feed systems used, the machine can also be used as a transfer press or progressive press. All machining processes are performed with a high press force of 630 tonnes. The drive system, in the form of a flywheel and an eccentric gear, cooperating with two connecting rods, ensures even torque transmission and smooth control of the slider movement. The slider, on the other hand, is guided at eight points using roller guides, which increas ...

LVD brand press - type TPI 80/25 - 80 ton

Ajax 1,000 Ton Straight Side Mechanical Forging Press S/N 4410 10” Stroke 33” Shut Height 36” x 36” Bed 80 Strokes Per Minute Partially Rebuilt Ajax 1,000 Ton Straight Side Mechanical Forging Press S/N 4621 10” Stroke 32” Shut Height 36” x 32” Bed 80 Strokes Per Minute Bolsters are included. Both presses are in working condition and under power.

NIDEC ARISA S-2-500-240-120-FD mechanical press was built in 2006 in Spain by Nidec Press & Automation Co. (NP&A). It is an extremely versatile press that is used in the series production of components for the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, i.e. precise punching and stamping of metal parts. In addition to its standard purpose, with the appropriate tooling and material feeding systems, the machine can also be used as a transfer press or progressive press. All processes are performed with a high press force of 500 tonnes. The drive system of the NIDEC ARISA S-2-500-240-120-FD press is based on a flywheel and an eccentric gear, cooperating with two connecting rods. This solution guarantees even torque transmission and a smooth working cycle. The slider, on the other hand, is guided in multiple points by rolle ...

Bombled 2100 x 4 mm Max sheetthickness: 4 mm Cuttinglength: 2100 mm Strokes/min: 33 str/min Electric motor (power): 5,5 kW Length : 3500 mm Depth : 1500 mm Height: 1100 mm Weight: 3100 kg

Type: 82.25 Max sheetthickness: 2 mm Cuttinglength: 2540 mm Electric motor (power): 3 kW Weight: 1600 kg

Copper plate for lapping machine. Dia 600mm, NEW, make: Melchiorre, Mimu Machine Tools Gussago BS Italy, Lapping is a machining process in which two surfaces are rubbed together with an abrasive between them, by hand movement or using a machine., This can take two forms. The first type of lapping (traditionally called grinding), involves rubbing a brittle material such as glass against a surface such as iron or glass itself (also known as the lap or grinding tool) with an abrasive such as aluminum oxide, jewellers rouge, opticians rouge, emery, silicon carbide, diamond, etc., between them. This produces microscopic conchoidal fractures as the abrasive rolls about between the two surfaces and removes material from both., The other form of lapping involves a softer material such as pitch or a ceramic for the lap, which is charged with the abrasive. The lap is then used to cut a harder mate ...

sheet width: 1050 mm plate thickness: 2,0 mm distance between columns: 1050 mm down holder: 1 Stück fence: Tisch 80 - 480 mm fence: Breiten 0 - 600 mm table-size: 1300 x 600 mm work height max.: 760 mm total power requirement: manuell kW weight of the machine ca.: 413 kg. range L-W-H: 2,0 x 1,04 x 1,6 m - Including adjustable stop on the work table for miter cuts - The knife can be lifted easily thanks to the counterweight on the back - Large work table for safe placement of the sheet metal plates - Sheets can be pushed through, i.e. longer sheets can be cut - Handwheel on the front to adjust the back gauge - Comes with a robust cast iron base as standard - Long service life thanks to knives made of quality steel - Standard with hold-down device including quick-release clamp - Robust machine construction for high stability Furnishing: - manual lever shears - stable execution - hold-down ...

gebr. Post-bending press Fabr. Graebener, Type GRNM, YOC 2005 max. bending force 16 t. Tool length 1,600 mm Adjustment of the underswing, hydraulic 2 cylinders Dimensions 5080 x 3290 x 2540 mm Kj Uovvlllerhyxkenb Weight 65 t.

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between tableand slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 E5931468 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

1 Pc Used Single Column Carousel Lathe Make STANKO Mod. 1514 Bauj. 1988 Face plate diameter 1400 mm Circumferential diameter 1600 mm Turning height 1000 mm Workpiece weight 8 t Face plate speed range 3Stages 1 - 355 rpm Main drive motor 55 kW Machine weight approx. 25 t CNC SIEMENS SINUMERIK 810T 1 pc. used two-stand vertical lathe Brand STANKO Mod. 1514 year of construction 1988 Face plate diameter 1400 mm Swing diameter 1600 mm Turning height 1000 mm Workpiece weight 8 t Face plate speed range 1 - 355 rpm Main drive motor 55 kW Machine weight approx. 25 t CNC SIEMENS SINUMERIK 810 T

Hoort bij Lijn -gt; P.14d 15917

Kircheis 2100 x 3 mm Max worklength: 2100 mm Max tickness: 3 mm Length: 3250 mm Depth: 800 mm Hight : 2000 mm Weight: 2,5 ton

Type: 230 Maximale buighoek: 180° Max worklength: 2040 mm Max tickness: 1,5 mm Distance between clampblock -- ram: 100 mm Eletric motor (power): 0,75 kW Weight: 1000 kg

This SEYI SN1-110 was manufactured in 2002. It is a mechanical C-frame crank press with a 110 tons capacity and a stroke of 110 mm. The machine offers an adjustable speed range of 35–65 SPM, a maximum die height of 350 mm, and a main motor of approximately 11 kW (15 HP). Contact us for more information about this machine.

This PRESSIX Pressix 25 CNR 4 was manufactured in 2012. Ideal for high-precision stamping, blanking, and continuous strip processing, it includes a manual decoiler, servo roller feeder G+K WVS/L 150, and a motorized recoiler. Consider the opportunity to buy this PRESSIX Pressix 25 CNR 4 mechanical stamping press. Contact us for more information.

This RAVNE PRESSES Manzoni 315 stamping machine was manufactured in 1992. It features a robust eccentric H-frame, monoblock design with a press force of 3150 kN and a drive power of 60 kW. It has a fixed stroke of 200 mm and slide dimensions of 2550 x 1250 mm. If you are looking to get high-quality stamping capabilities, consider the RAVNE PRESSES Manzoni 315 machine we have for sale. Contact us for more information.

This stamping machine was manufactured in 1992. It features a robust Eccentric H-frame, monoblock design with a press force of 1600 kN and a fixed stroke of 160 mm. The machine includes a magnetic conveyor for scraps, a quick die cart system, and a millutensil oiling system. Ideal for high-quality stamping capabilities, consider the RAVNE PRESSES Manzoni 160 machine we have for sale. Contact us for more information about this machine.

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between table and slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

Mechanical stamping press manufactured in 2002. This PRESSIX 160 CNR 6 features a capacity of 160 tons and an adjustable stroke ranging from 20 to 200 mm. It operates at a speed of 20 to 70 strokes per minute and includes a motorized slide adjustment of 100 mm. The table dimensions are 1100 x 700 mm, providing ample workspace. If you are looking to get high-quality stamping capabilities, consider the PRESSIX 160 CNR 6 machine we have for sale. Contact us for further details.