용접 기계 사용 판매를 위해 (1,740)

attention: the machine can be transported on a standard truck!Additional technical specifications:• Laser source: ROFIN-SINAR, type: 2000 SM• incl. extraction system

For all further data, see the photographed nameplate.

Attention: probably defective!

Incl. 3-jaw chuck, diameter: 120 mm.

on mobile base frame

Additional technical specifications:• Hole diameter: 30 mm• Distance from hole center to hole center: 100 mm

Auflagefläche: ca. 2330 x 1500 mm

• Hole diameter: approx. 30 mm

제안 26036 기술 자료 대략: - 적재 용량 약 3000kg - 페이스플레이트 직경 1520mm - 모터로 페이스플레이트를 기울일 수 있음 - 회전식 전기 장치. 무한 가변 - 용접 전류 전송 650A - 드라이브 400 V - 수평 위치에서의 테이블 높이 대략 1450 mm - Re- + 반시계 방향 회전 - 휴대용 리모컨 - 풋스위치 - 공간 요구량 대략 W 1700 x H 1500 x D 2300 mm - 무게 약 2800 kg

TIG hose assembly, welding torch, hand welding torch, TIG torch -TIG hose package: water-cooled DIN EN 60974 -Length: 6.5 m -Connector: 4-pin -Transport dimensions: 400/400/H100 mm -Weight: 3.1 kg

TIG hose assembly, welding torch, hand welding torch, TIG torch -TIG hose package: water-cooled -Length: 4 m -Connector: 5-pin -Transport dimensions: 340/340/H100 mm -Weight: 2.4 kg

Ventilation duct, chip extraction, dust extraction, extraction system, ventilation ducts and fittings, spark trap -Spark trap: with copper lamellae -Connection: Ø 320 mm -Dimensions: 480/440/H470 mm -Weight: 38 kg

TIG hose assembly, welding torch, hand welding torch, TIG torch -TIG hose package: water-cooled -Length: 8.4 m -Connector: 2-pin -Transport dimensions: 400/400/H100 mm -Weight: 4.1 kg

Ventilation duct, chip extraction, dust extraction, extraction system, ventilation ducts and fittings, spark trap -Spark trap: with copper lamellae -Connection: Ø 320/250 mm -Dimensions: 760/440/H470 mm -Weight: 40 kg

Ventilation duct, chip extraction, dust extraction, extraction system, ventilation ducts and fittings, spark trap -Spark trap: with copper lamellae -Connection: Ø 400 mm -Dimensions: 680/510/H540 mm -Weight: 48 kg

Gas metal arc welding machine, arc welding machine, MIG/MAG welding machine, pulse welding machine, inverter welding machine, impulse welding machine -Manufacturer: Messer Griesheim, MIG/MAG gas-shielded welding machine -Type: Euromag 25-2 -Max. welding power: 250 A -Wire feed: 4-roll drive, separate, mobile -Accessories: Hose assembly, ground cable (see photos) -Dimensions: 970/490/H890 mm -Weight: 168 kg

DALEX PMS 10-4 및 COHLINE 물 냉각기 DALEX, PMS 10-4 타입으로, 강력하고 견고한 산업용 스팟 용접기로, COHLINE 수냉 유닛과 함께 즉시 사용 가능한 세트로 구성되어 있습니다. 하이라이트 및 컨디션: 극히 낮은 주행 거리: 내장된 DALEX MPS 100 디지털 제어 시스템은 원래 주행거리 측정치가 단 13,282 사이클에 불과합니다! 이 정도 산업용 기계치고는 거의 새것과 같으며 마모가 최소화됩니다. 높은 전극력: 이 모델은 두꺼운 판상에서도 완벽한 스팟 용접을 위해 최대 690 dN의 강력한 접촉 압력을 제공합니다. 냉각 포함: 강력한 COHLINE 냉각 장치(5.8kW) 덕분에 기계는 과열 없이 즉시 영구 산업용 교대 운전에 적합합니다. 유연성 및 안전성: 발 스위치와 양손 안전 콘솔 중 쉽게 선� ...

wire electrode, welding wire, welding wire -Manufacturer: Elgar, started roll of MAG wire electrode -Type: Cromacore DW-309L O1.2mm -Dimension: O 300/100 mm -Weight roll: 10.1 kg

제안 26289 기술 데이터 대략 : - 2개의 버너가 있는 CNC 화염 절단기 - 버너 높이 2개 + 틸트 조절 가능 - 궤간 대략 4.2 m - 트랙 길이 대략 7.5 m - 트랙 높이 대략 0.5 m - 공간 요구량 대략 L 8 x W 7.5 x H 2.3 m - 무게 대략 3 T - 지지 테이블 없�

A central welding fume extraction system is offered. Airflow: 30000m³/h, airflow: 30000m³/h, motor power: 30kW, compressed air connection: 6-8bar, max. static pressure: 2500Pa, duty cycle: 100%, control: PLC. The system is equipped with 2 spark traps and various ductwork components (extraction arms and hoods not included). An inspection is possible by arrangement.

An industrial welding robot is offered. Reach: 1450mm, payload: 5kg, operating hours: 2213h, welding power source: ESAB AristoMig 500W, max. welding current: 500A, duty cycle: 60% at 500A/100% at 400A, controller type: IRC, robot variant: 1600-5/1.45, controller: IRC. Equipment: ESAB AristoMig 500W welding power source, IRC control cabinet, linear axes/positioner tracks. Weight: approx. 500kg, overall dimensions X/Y/Z: approx. 1200mm/800mm/1600mm. An inspection is possible by arrangement.

Working range: 1250x2250mm, max. feed speed: 48m/min, welding range: M3-M8, welding diameter: 3-8mm, stud length: 8-40mm, max. welding capacity: 30-40studs/min, max. feed: 48m/min, positioning accuracy: +/-0.2mm, length: 2400mm, width: 2700mm, height: 3100mm, the machine has been used very little and is in good condition. An on-site inspection is possible.

Max. load capacity: 30t/set, min. workpiece diameter at 90°: 466mm, max. workpiece diameter at 30°: 11457mm, roller dimensions: 520mm×355mm, roller covering: rubber, max. speed: 1295mm/min, motor power: 2×1.5kW, weight drive unit/idler unit: 1300kg/700kg. Documentation available. An on-site inspection is possible.

Welding power source: Starmatic 1003 DC, max. welding current: 1000A at 100% duty cycle, lifting column height: 4850mm. Including flux tray, rail and vessel turning device. Documentation available. An on-site inspection is possible.

Laser source: Bystronic BLT 3500 Turbo, laser power: 3500W, wavelength: 10600nm, max. sheet weight: 160kg/m². Base machine weight: approx. 7000kg, laser source weight: approx. 1600kg. Documentation available. An on-site inspection is possible.

제조사 및 모델: 아이딜 BAS 050-11 정격 전력(ED 50%): 4.5 kVA 2차 전압: 2.6 – 4.4 V (6단계) 클램핑 힘: 10 kN (유압) 최대 압축력: 2.2 kN IISC 본부 E Rrszqdkxjvef 기계 중량: 약 180kg 유압 장력 조절, 풋 스위치로 작동됨 파이로미터(GTR): 네 (터치 패널에 온도 표시) 연결 전압: 380 – 419 V 바이메탈/카바이드 톱날: 6×0.6 – 34×1.1 mm 목재 톱날: 6×0.4 – 50×1.0 mm 스테인리스 스틸 톱날: 6×0.4 – 25×0.5 mm 블레이드 크기: 6×0.4 – 30×0.6 mm 블레이드 스틸 S235JR: 최대 단면적 75 mm² 블레이드 강 X5CrNi18-10: 최대 단면적 40 mm² 파이로미터 / GTR: 통합 파이로미터(GTR)는 어닐링 공정 중 비접촉 온도 측정을 가능하게 합니다. 목표 온도는 레시피에 미리 정의되어 패널에 표시되며, 설정 온도에 도달하면 � ...

An MBK horizontal cage welding machine for the production of small square reinforcement cages is offered. Cage diameter: approx. 200mm-1500mm, max. cage length: 4000mm, wire diameter: 5mm-12mm, welding capacity: approx. 100kVA, control: Zoller+Fröhlich. Machine dimensions: approx. 6000mm/2500mm/2200mm, weight: approx. 8500kg. Inspection possible by arrangement.

Welding rectifier, standard: EN 60974-1, VDE: VDE 0544, mains connection: 3~/400V/50Hz, fuse protection: T25A, open-circuit voltage: 76V, max. welding current: 400A, protection class: IP23, insulation class: F, cooling method: AF-forced air cooling, weight: 214kg. An on-site inspection is possible.

Working area X/Y: 1500mm/3000mm, plasma source: NERTAJET HP120, control: DIGISAF 100, max. cutting capacity steel/stainless steel/aluminum: 20mm/15mm/20mm, wet and dry cutting possible, extraction system available. Documentation available. Inspection possible by arrangement.