sous-catégories
(troisième niveau de catégorie)
Fabricant:
(Catégorie: 107)
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 6mm total power requirement: 11 kWweight of the machine ca.: 5,8 tdimensions of the machine ca.: 4880 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: unbkt. mmdouble T-iron on the x-axis: unbkt. mmU-iron on the x-axis: unbkt. mmtotal power requirement: 30 kWweight of the machine ca.: 8,6 tdimensions of the machine ca.: 2500x2000x1900 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 (500) mm: 45 (500) mmL-beam: 80 x 80 x 8 (800) mmT - beam - web outwards: 80 x 9 (800) mmAxis diameter: 60 mmwork speed: 5,0 m/minTool diameter: 195 mmtotal power requirement: 3 kWweight of the machine ca.: 1,0 tdimensions of the machine ca.: 1,2 x 0,9 x 1,2 mProfile bending machine with:- Foot pedal right / left- Recording: wave 50mm- with digital display- hardened special steel shafts- 1 set of standard rollers- Lower rollers are driven- Upper roll up and down hydraulically deliverable- Horizontal and vertical operation- Engine with braking deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1000 mmplate thickness: 5,0 mmdistance between columns: 1070 mmdiameter of upper rolls: 130 mmtotal power requirement: 4,0 KWweight of the machine ca.: 1,15 tdimensions of the machine ca.: 2,55 x 0,65 x 1,1 mm- Electrically adjustable rear roller- Electrically adjustable lower roll (material clamping)- Digital readout for rear roller movement- Digital readout for lower roll movement (material clamping)- Hardened rolls- Conical rolling- Swiveling top roll- Brake motor- Emergency stop- Documentation- 400VThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
épaisseur de la plaque: 1,6 mmpression: 450 MPa: 150 x 150 x 90 surface table: 650 x 500 mm: 875 mm angle de coupe - lame supérieure: 4 poids de la machine ca.: 75 kg• machine à entailler manuelle avec cadre inférieur • épaisseur de la feuille (acier 450MPa) à 1,6 mm, aluminium à 2,25 mm, plastique à 3,0 mm, • machine de démonstration
largeur de la feuille: 2020 mmépuissance de la plaque: 1,5 mmdistance entre les colonnes: 2050 mmdétraitage de la lumière du jour: 100 mmdésoutance totale: 0,75 kWpoids de la machine ca.: 1 tdimensions de la machine ca.: 2,7 x 1 x 1,5 m
plate thickness: 1,25 mmroll-body distance: 250 mmthroat: 260 mmdistance between roll centers: 62 mmtool adaptor: 26 mmspeed: 6,3 m/mintotal power requirement: 0,7 kWweight: 170 kgrange L-W-H: 1020x600x1500 mmDomestic equipments:- motor driven beading machine- 5 sets of bead rollers- Footswitch- Operating instructions in German- CE mark / Declaration of ConformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
largeur de la tôle: 1500 mmépuissance de la plaque: 1,5 mmdistance entre les colonnes: 1500 mm angle de pliage max.: 135 désoutance totale requise: - kWpoids de la machine ca.: 0,36 tdimensions de la machine ca.: 1,7 x 0,7 x 1,3 m
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 8mm total power requirement: 15 kWweight of the machine ca.: 14,1 tdimensions of the machine ca.: 6310 x 1660 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 13mm total power requirement: 22 kWweight of the machine ca.: 21,3 tdimensions of the machine ca.: 6560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mmdouble T-iron on the x-axis: siehe TD mmU-iron on the x-axis: siehe TD mmtotal power requirement: 1,5 kWweight of the machine ca.: 0,385 tdimensions of the machine ca.: 930 x 730, x 1400mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 11 kWweight of the machine ca.: 4,570 tdimensions of the machine ca.: 3830 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 15 kWweight of the machine ca.: 8 tdimensions of the machine ca.: 4260 x 1160 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 30mm (S) total power requirement: 37 kWweight of the machine ca.: 15,3 tdimensions of the machine ca.: 4510 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 16 total power requirement: 37 kWweight of the machine ca.: 23,81 tdimensions of the machine ca.: 6560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mmdouble T-iron on the x-axis: siehe TD mmU-iron on the x-axis: siehe TD mmtotal power requirement: kWweight of the machine ca.: 0,6 tdimensions of the machine ca.: 1000 x 700 x 1380mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Presse à découl TRUMPF TrumaBend V 85 Année de construction 1999 Machine d’occasion Données techniques: - longueur de travail max. 2050 mm - Passage de support 1750 mm - force de pression max. 850 kN - Distance table / pilon 410 mm - Chargement 410 mm - Hub 285 mm - vitesses de levage - Vitesse descendante vitesse d’urgence 200 mm/sec - Vitesse ascendante 135 mm/sec - Vitesse de pression descendante 1 - 11 mm/sec - Puissance d’entraînement totale 13 kVA - encombrement env.B 3700 x H 2700 x T 2100 mm - Poids env. 8000 kg
VERRINA CLR 216 X 4050 Machine à plier en tôle Rouleau double avec 4 rouleaux et double pression Année de production 1979 Capacité 4000 mm x 16 mm Longueur du rouleau 4050 Rouleaux latéraux de diamètre 370mm haut et sous-rouleau 410mm Le rouleau monte et tombe 370mm Entrée 400/3/50 Hz 52 kW Vitesse de laminage 2,9 / 3,9 / 6,8 mètres par minute Contrôle de la console de commande Equipé d’une chute hydraulique, câble de sécurité Longueur 9000mm Largeur 2350 mm Hauteur 2400 mm Poids net environ 29.500 kg
Données techniques: - Puissance d’impression 100 KN / 10 t - Force de pression réglable 0 - 100 kN - Longueur de levage 0 - 150 mm - Largeur lumineuse env. 200 mm - Vitesse de levage 0 - 0,6 m/min - Hauteur de l’outil jusqu’à environ 100 mm - Puissance de cintrage - avec Prisma MW 100 plat à environ 100 x 12 mm - Plier le tube jusqu’à environ 1 pouce - Puissance directionnelle Wy à distance de 1m 100 cm³ - 400 V / 1,1 kW - Env. B 1100 x H 1000 x T 650 mm - Poids env. 400 kg
Machine à pivoter hydraulique - machine de commande (délai de livraison env. 10-14 semaines), incl. bombardiers hydrauliques dynamiques, écran tactile, Régulation de la pression de la Haute-Wange, attaque arrière (1000 mm), pieds de chèvre avec pince à outils automatique, électrique./hydr. Réglage de la courbure - des graphiques similaires
plate thickness: 2,5 mmroll-body distance: 260 mmthroat: 500 mmdistance between roll centers: 92 mmtool adaptor: 35 mmspeed: 3,5 m/mintotal power requirement: 1,5 kWweight of the machine ca.: 295 kgdimensions of the machine ca.: 1200x700x1200 mmDomestic equipments:- motor driven beading machine- 3 sets of bead rollers- Footswitch- Operating instructions in German- CE mark / Declaration of ConformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round bar steel: 50 mmsquare edge steel: 40 x 40 mmL-beam: 140 x 13 mmPunch power: 900 kNhole punching press: throat: 510 mmhole punching press: max. length of stroke: 29 mmhole punching press: capacity (dia. x thick.): 31 x 20 mmnotching: l + T material: 80 x 14 mmno. of strokes: 40 / 45 Hub/mintotal power requirement: 4 kWweight of the machine ca.: 3,7 tdimensions: 2,1 x 0,7 x 2,12 mAccessories: various punches and diesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 tchamfer lenght: 4000 mmdistance between columns: 3060 mmcontrol: FORTRON CNC 10 H 4 throat: 280 mmstroke: 250 mmdayligth: 500 mmtable length: 4050 mmtable width: 280 mmfeed down: 70 mm/secfeed up: 68,4 mm/secworking feed: 9 / 3,5 mm/secoperating pressure: max. 205 baroil volume: 400 ltotal power requirement: 19,5 kWweight of the machine ca.: 20,8 tTotal weight including accessories: 22 tdimensions of machine L x W x H: 4,8 x 1,88 x 2,93 mdimensions of switch cabinet: 1,6 x 0,5 x 2,25 mAcc.: programmable back gauge, upper and lower dies, table extensionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 6 total power requirement: 7,5 kWweight of the machine ca.: 4,340 tdimensions of the machine ca.: 3830 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 8mm total power requirement: 15 kWweight of the machine ca.: 9,7 tdimensions of the machine ca.: 5310 x 1660 x 1590 mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
nouveaux
sheet width: siehe TD mmplate thickness: siehe TD mmdistance between columns: siehe TD mmpre-bending: siehe TD total power requirement: 3 kWweight of the machine ca.: 1,06 tdimensions of the machine ca.: 1260 x 1350 x 1900 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 18,5 kWweight of the machine ca.: 8,5 tdimensions of the machine ca.: 4260 x 1660 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD 0: 20mm (s) Ampullen/h0: mm0: mmtotal power requirement: 22 kWweight of the machine ca.: 9,2 tdimensions of the machine ca.: 4260 x 1660 x 1590 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mmdouble T-iron on the x-axis: siehe TD mmU-iron on the x-axis: siehe TD mmtotal power requirement: kWweight of the machine ca.: 0,2 tdimensions of the machine ca.: 800 x 700 x 1200mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mmplate thickness: siehe TD mmdistance between columns: siehe TD mmtotal power requirement: 7,5 kWweight of the machine ca.: 3,23 tdimensions of the machine ca.: 3200 x 2300 x 1350 mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
