钣金加工设备 二手 出售 (3,374)

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 13mm total power requirement: 22 kWweight of the machine ca.: 21,3 tdimensions of the machine ca.: 6560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

角铁/腿长度： 见 TD mm双 T 型铁 x 轴： 见 TD mmU-Iron 在 x 轴上： 见 TD mm总功率要求： 1.5 kW机器重量 约： 0.385 t空间要求 约： 930 x 730， x 1400mm m电动型材弯曲机 DURMA类型： PBM 50建造年份： 新轴直径 50mm球直径： 165mm电机功率： 1.5kW转速： 3.6 m/sec.重量：385kg长度：930mm宽度：730mm高度：1400mm 此列表的数据是使用ModulMWS创建的 - LogoTech oHG的机器管理�

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 11 kWweight of the machine ca.: 4,570 tdimensions of the machine ca.: 3830 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 15 kWweight of the machine ca.: 8 tdimensions of the machine ca.: 4260 x 1160 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 30mm (S) total power requirement: 37 kWweight of the machine ca.: 15,3 tdimensions of the machine ca.: 4510 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 16 total power requirement: 37 kWweight of the machine ca.: 23,81 tdimensions of the machine ca.: 6560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

角铁/腿长：见TD mm双 T 型铁 x 轴： 见 TD mmU 型铁 x 轴： 见 TD mm总功率要求： kW机器重量 约： 0.6 t空间要求 约： 1000 x 700 x 1380mm m电动型材弯曲机 DURMA类型： PBM 45结构年份： 新轴直径 45mm球直径： 162mm电机功率： 1.5 – 0.75kW转速： 3.9 m/sec.重量：600kg长度：1000mm宽度：700mm高度：1380mm图相 似数据量，此列表是使用ModulMWS创建的 - LogoTech oHG的机器管理�

折弯机 TRUMPF 特鲁玛弯 V 85 建造年份 1999 机器 规格： 最大工作长度 2050 mm - 支架通道 1750 mm - 冲压力 850 kN - 测距台/柱塞 410 mm - 支架投影 410 mm - 柱塞行程 285 mm - 提升速度 - 下行速度快速移动200毫米/秒 - 上升速度 135 毫米/秒 - 向下按压速度 1 - 11 毫米/秒 - 总驱动功率 13 kVA - 空间要求约 W 3700 x H 2700 x D 2100 mm - 重量约8000公�

维瑞纳 CLR 216 X 4050 钣金圆弯机 双辊，带 4 个辊筒和双压力 制造年份 1979 容量 4000 mm x 16 mm 卷筒长度 4050 卷筒直径侧辊 370mm 顶部 / 底部卷筒 410mm 滚升降370mm 输入 400/3/50 Hz 52 kW 轧制速度 2.9 / 3.9 / 6.8 米每分钟 控制控制面板 配备液压落锤、安全电缆葫芦 长度 9000mm 宽度 2350 mm 高度 2400 mm 净重约 29，500 kg

规格： - 承压能力 100 KN / 10 t - 压缩力可调 0 - 100 kN - 行程长度 0 - 150 mm - 清除宽度约 200 毫米 - 提升速度 0 - 0.6 米/分钟 - 工具高度可达约 100 毫米 - 弯曲性能 - 带棱镜 MW 100 平板至约 100 x 12 毫米 - 管子弯曲到大约 1 英寸 - 定向功率Wy在拉直块距离为1m 100 cm³ - 驱动 400 V / 1.1 kW - 空间要求约为 宽 1100 x 高 1000 x 深 650 mm - 重量约 400公�

- 扁平钢剪切机切割扁平，最大可达 100 x 18 mm - 刀长约 250 毫米 - 型钢剪刀切割角度 - 90 至 100 x 10 mm - 45 至 70 x 8 mm - 棒钢剪切切割圆钢 90 至 36 mm - 方形钢 90 至 30 mm - 开槽设备片材可达 8 mm - 打孔机 - 压力容量约 50 吨 - 投影 350 mm - 在15毫米内冲穿钢，最大20毫米 - 驱动 400 V / 3 kW - 空间要求约为 宽 1100 x 高 1700 x 深 2300 mm - 重量约 1900公�

液压旋转弯曲机 - 订购机（交货时间约10-14周），包括。 液压动态顶篷，触摸屏， 上脸颊的压力调节，后挡板（1000mm），山羊脚，带自� ��工具夹紧，电气/液压。调整弯曲的脸颊 -相似图片- 液压数控折弯机 - 订购机器（交货时间约10-14周），包括。 液压动态外倾角，触摸屏， 上梁压力调节，后挡风口（1000mm），带自动工具夹紧� ��山羊脚，弯曲梁的电动/液压调节 -图片相似-

液压旋转弯曲机 - 订购机（交货时间约10-14周），包括。 液压动态顶篷，触摸屏， 上脸颊的压力调节，后挡板（1000mm），山羊脚，带自� ��工具夹紧，电气/液压。调整弯曲的脸颊 -插图相似- 液压数控折弯机 - 订购机器（交货时间约10-14周），包括。 液压动态外倾角，触摸屏， 上梁压力调节，后挡风口（1000mm），带自动工具夹紧� ��山羊脚，弯曲梁的电动/液压调节 -图片相似-

压力：55吨孔径在板材厚度：40英寸10毫米投影：500毫� ��行程：60毫米每分钟冲程20毫米行程：38 /分钟。电机功率：5 kW机器重量约：1，150 kg机器尺寸：1500x1100x2000 mm配件/设备：- 冲床为您服务机器租赁长达60个月，无需首付，无残� �，个人建议和根据要求计算个人租赁费率。该广告的 数据是使用模态MWS创建的 - 标识科技oHG的机器管理�

sheet width: 3100 mmplate thickness: 10 mmcutting angle: 2 °down holder: 14 Stückno. of strokes: 13 Hub/minthroat: 350 mmoil volume: 260 ltotal power requirement: 22 kWweight of the machine ca.: 10.550 kgdimensions of the machine ca.: 4000x2250x2050 mmDomestic equipments:- Hydraulic swing cut sheet metal shears- Touch screen controller with digital display for backgauge- automatic kerf adjustment via the control- Backgauge control 1000 mm travel with recirculating ball screws- Vibration cutting machine with kerf adjustment- 2 support arms- 1 side stop- Photocell behind the machine- Cutting length limit- cut line lighting- Chrome steel knife- Ball rolls in the table- hinged finger guard with limit switch- Footswitch- CE mark / Declaration of Conformity- Bed instructions in GermanThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mmplate thickness: 6 mmvoltage: 380 Vcontrol: CYBELEC CybTouch down holder: 14 Stückcutting angle: 1,2 °total power requirement: 11 kWweight of the machine ca.: 5700 kgdimensions of the machine ca.: 4000x2100x1640 mmAccessories / equipment:- CYBELEC Cybtouch touch screen controller- NC controller for backgauge, gap adjustment, number of pieces,cutting length- 1 side stop with scale, T-groove and tilting cam- 2 front support arms- cut line lighting- Cutting gap adjustment- Cutting length limit- Folding finger guard with limit switch- motorized back gauge 1.000 mm travel- Ball screws- Photocell behind the machine- Ball rolls in the table- SIEMENS electrical system- BOSCH / HOERBIGER hydraulic system- Footswitch- CE mark / Declaration of Conformity- Operating manual: Machine and control in GermanThe data for this ad was created with ModulMWS - the software solution of Lo ...

压力：110吨冲孔能力：40x20毫米 投影：500毫米电机功率：9千瓦冲程率：28冲程/分钟冲 程 最大：80毫米重量：3150公斤配件/设备：- 冲床为您服务机器租赁长达60个月，无需首付，无残� �，个人建议和根据要求计算个人租赁费率。该广告的 数据是使用模态MWS创建的 - 标识科技oHG的机器管理�

板材厚度：2.5 mm滚筒体间距：260 mm投影：500 mm滚筒中心距离：92 mm安装：35 mm速度：3.5 m/min总功率要求：1.5 kW机器重量约：295 kg空间要求约：1200x700x1200 mm设备：- 电动串珠机- 3 套渗流辊- 脚踏开关- 德国- CE 标志/符合性声明上的操作说明为您服务机器租赁长达 60个月，无需首付，无残值，个人建议和根据要求计� �个人租赁费率。该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理�

: 32 /minPunching force: 60 to throat: 500 mm: 40x11 mm: 350x15 mm: 350x15 mmL-beam 90°: 120x120x10 mm: 45 mmsquare edge steel: 40 mm: 10 mm: Aufnahme bis max. 150x10 engine output: 5,5 kWweight: 2012 kgBasic equipment:- Flat steel shears with knife set- Angle shears with knife set- Punch with quick release device for punches up to 40 mm- Support table for punching device- Triangular notching device- Support table for notching- bending station- Bending stamp with matrices V 40 and V 70- electrical contact stop (1 meter)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /minPunching force: 60 to throat: 250 mm: bis max. Ø 40x11 mm: 350x15 mm: 350x15 mmL-beam 90°: 120x120x10 mm: 45 mmsquare edge steel: 40 mm: 10 mm: Aufnahme bis max. 150x10 engine output: 5,5 kWweight: ca. 1600 kgBasic equipment:- Flat steel shears with knife set- Angle shears with knife set- Punch with quick release device for punches up to 40 mm- Support table for punching device- Triangular notching device- Support table for notching- bending station- Bending stamp with matrices V 40 and V 70- electrical contact stop (1 meter)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Punching force: 45 t hole diameter in sheet thickness: Ø 27x13 mm: 24 /minL-beam 90°: 80x80x8 mmL-beam 45°: 60x60x6 mmflat steel: 200x13 mm: 7 mmengine output: 2,2 kWweight: 760 kgBasic equipment:- Complete set of blades for flat steel shears- Complete knife set for angle steel shears- Compl. Standard punching device- Stamp quick release device for punches up to 27 mm diameter- Rectangular notching device compl. with hold down- notch- Support table for punching deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWrange L-W-H: 900 x 600 x 1000 mmweight: 470 kgconnected load: 400/50 V/HzEquipment / Accessories:- Three driven rollers- Manual delivery of the upper roller- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turnused different profilesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

板材厚度：4 mm辊筒体间距：260 mm投影：500 mm卷筒中心距离：132 mm安装：40 mm速度：5 m/min总功率要求：2.2 kW机器重量约：350 kg空间要求约：1650x700x1280 mm设备：- 电动串珠机- 3 套渗流辊- 脚踏开关- 德国- CE 标志/符合性声明上的操作说明为您服务机器租赁长达 60个月，无需首付，无残值，个人建议和根据要求计� �个人租赁费率。该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理�

shaft diameter: 60 mmShaft revolutions: 6 U/minroll diameter: 215 mmpressure hydraulic cylinder: 180 kNdimensions: 1125x870x1620 mmweight: 820 kgAccessories / Equipment:- Three driven rollers- Hydraulic delivery of the upper roller- Working position horizontal and vertical- Digital display with memory function- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: R10-R260 : max. 210 °: 54x2 mm: 42x2,5 mm: 42x3,5 mm: 30 mmbending speed: max. 4 U/minAmount of programms: 30x9 voltage: dreiphasig 220-400 Vtotal power requirement: 1,1 kWdimensions of the machine ca.: 1000 x 410 x 570 mmweight of the machine ca.: 80 kgAccessories / equipment:- Machine structure: aluminum alloy- Base: welded steel- Standard accessories (including footswitch, operating instructions)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mmplate thickness: 6 mmvoltage: 380 Vcontrol: CYBELEC CybTouch down holder: 14 Stückcutting angle: 1,2 °total power requirement: 11 kWweight of the machine ca.: 6.300 kgdimensions of the machine ca.: 4000x2100x1640 mmEquipment:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. can be folded up at max. Traverse path, for longer cuts- 1x side stop- 2x front support arms- Ball casters in the front support table- hinged finger protection, with safety switch- BOSCH / HOERBIGER hydraulic system- SIEMENS electrical system- light barrier behind the machine (safety device)- foot switch- CE mark / declar ...

: 400 kNstroke length max.: 285 mmworking feed: 9 mm/secreturn speed: 20 mm/sec: 660x1250 mmwork height max.: 930 mmtoolpiece height max.: 250 mmtotal power requirement: 4 kW: 200x26 mmbending capacity max. - round: 60x5,0 mmweight: 1050 kgDomestic equipments:- semi-automatic NC control (99 programs with 16 steps each)- incl. bending bolt (without punch)- Incl. tool holder for dies- incl. foot pedalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 45 to.no. of strokes: 24 Hub/minhole diameter in sheet thickness: max. Ø 27 in 13 mm: 80x80x8 : 60x60x6 mmflat steel: 300x10/200x13 mm: 7 mmengine output: 2.2 kWrange L-W-H: 1550x820x1540 mmweight: 760 kgStandard equipment:- Complete knife set for flat steel shears- complete knife set for angle steel shears- complete standard punching equipment- Stamp quick release device for punches up to Ø 27 mm- Rectangular notching device complete with hold-down device- notch- Support table for punching deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mmplate thickness: 25 mmpre-bending: 20 mmupper roll diameter: 390 mmlower roll diameter: 360 mmside roll diameter: 300 mmtotal power requirement: 18,5 kWweight of the machine ca.: 17.100 kgMachine dimensions approx.: 5800x2100x2000 mmAccessories / equipment:- Conical bending device- induction hardened rolls- digital display for side rollers- Machine made of steel construction- Separate control panel- two speeds- all rollers on ball bearings- Folding and support bearing from the top roller is actuated from the control panel.When the folding bearing is opened, the roller moves automatically upwards.- Conical adjustment of the rollers via control panel- Central rollers are via hydraulic motor and rotary reduction geardriven. (Top and bottom rollers)- CalibrationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWconnected load: 400/50 V/Hzhydraulic pump: 1,1 kW: 80 kNrange L-W-H: 900 x 600 x 1000 mmweight: 470 kgEquipment / Accessories:- Three driven rollers- Hydraulic delivery of the upper roller- Digital display with memory function- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turnused different profilesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.