ide 압출기 사용 판매를 위해

see PDF attached

Material: PVC // Screw diameter 52-104 mm (conical), counter-rotor, motor: 15 kW, capacity: 20 - 140 KG/hr.

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

Multiple extruders

Key data: 100 , 140

Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station � ...

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

Iddon Cold Feed Extruder. 2.5" screw dia. 10/1 LD Ratio. Motor Size 20.4/5.5 HP

Nordson / Puffe Extruder Plant Ex20 -1xPS01-1xPE20-1 for melting hot melt adhesives and thermoplastics, feeding as granules. Melting capacity according to the manufacturer's specifications up to 20 litres/h (EX20) Price: 45.000, -- € plus 19% VAT (Gross price incl. VAT 53.550, -- €) EXW Manufacturer: Nordson / W. Puffe Hotmelt-Technology Model No.: Ex20 -1xPS01-1xPE20-1 Year of manufacture: 05/2006 Serial No. 226260231/001 Power: 15 kW, connection 380V three-phase current Emergency stop, traffic light, CE mark Made in Germany Compact system mounted on a stable rolling frame (H= 198 cm, W= 160 cm, D= 110 cm) consisting of Nordson extruder, gear metering pump, Lenze worm drive, control cabinet with Allen-Bradley control, graphical user interface, storage tank, operating manual. Auxiliary: Labotec Minifeed Suction Conveyor MF60 Serial No. 12-103-00669 (Owner's man ...

Industrieöfen- Fertigung und zirlguss Reparatur jeglicher Art Wartung und Einregulierung von Industriebrennern Industrieöfen für Öl, Gas oder elektrisch beheizt Umfangreichen Sortiments an Feuerfeststeinen, Feuerfestmassen, Isoliermaterialen und Gießereihilfsstoffe namhafter Hersteller. Renovierungen und Instandsetzungen von Ofenanlagen Brenner einstellungen von Ofenanlagen schoenheider Modernisierungen von Ofensteuerungen Umrüstu ng von elektrischen Öfen auf gasbeheizte Öfen Umrüstung alter Heizsysteme auf Rekuperation gienanth Öfen Verzinkungsofen Ve rgüteofen Anlassofen Industrieöfen Glühofen Ovens laboratory ovens industrial furnaces industrial furnace plants Industrial Furnaces high-temperature chamber furnaces hardening furnace anlageHärteöfen Annealing furnaces Conveyor belt Abg aswäscher Abkühlungsöfen Abwärmerückgewinnung Aluminiumgiessereimaschinen ...

Key data: 150 mm

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Key data: 30 , 28 , 110

Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper

Key data: 30 , 28 , 110

Plant for the production of filament for use in 3D printers Capacity up to 10 kg/h consisting of 30 mm extruder, stainless steel trough, puller and winder with traverse guide

EXTRUDER

R 537: Recycling plasticizer (roller extruder) "MTA" Year 86, drive 200KW, plasticizing capacity approx. 800-1000kg/h, ideal for recycling plastics. The facility consists of the following parts: -Roller extruder -Batcher -Shearing device -Motor 200KW -Engine control cabinet "Schorch" -1 lattice box pallet spare parts FUNCTIONALITY: Ground plastic waste is fed into the plasticizer ------- heating ------- sausage kneading ------- shearing depending on the workpiece weight ------- further processing in presses The recycled plastic waste was used to make large parts such as garbage containers, plastic pallets, benches, flower pots, etc.

Extruder KE 90 x 30-D for manufacturing of von TPE foam and compact profiles screw diameter: 90 mm L/D ratio 30:1 (2700mm) extruder with 11 temperature-controlled zones (electrically heated by fluids) Siemens electric drive, motor 45kW at 2500rpm year of construction 1996, machine in very good condition (preliminary used in test operations) melt application device (gear pump) double profil head (also used for extrusion-coaded framework belts) electric equipment partially available extruder mounted on movable baseplate

T-Die Serial No.: L 1081-041391 // Calender Serial No.: F 1201-041392 Haul-Off Serial No.: F 1201-041392-T Max. winder speed: 50 m/min Type: Film system 1080 mm usable width Equipment / Additional information: Max. gross output PP up to 1000kg/h with film width up to 1200mm A special feature is the winding system, which can cut narrow films (150 mm - 100 mm) or for example 8 x 175 mm or even 2 x 700 mm one nozzle lip with a max. film thickness of 2mm up to 1000kg/h. Total power consumption: 211 kW/h Main engine power: 250 kW Min. 068 mm film thickness in PS / min. 0.75 mm in PP Maximum calender speed: Max. 50 m/min. mechanically possible Consists of: -Dosing system 5-chamber Maguire -Extruder (160 mm screw) Amut EA 160 // Age: 2003 -Screen changer (for cleaning in food production) -Melt pump -Slot die (1 insert) 120 cm -Lip with max. film thickness up to 2mm up to 1 ...

EDI Autoflex Extrusion Die width 900 mm.

A fully equipped line for the production of nonwovens Spunbond Type YS 2400: Manufacturer: Faré (Italy) Useful width: 2400 mm Capacity: up to 514 kg/h Nonwovens weight: 10-100 g/m2

Barwell Hydraulic Extruder – Used For sale: a used Barwell hydraulic extruder, designed for processing rubber compounds and elastomers. Barwell machines are well known worldwide for their robust construction, reliability, and consistent performance in industrial applications. The machine has been operated in an industrial environment, regularly maintained, and remains in good technical condition. Ready for further use after installation. Key features and advantages: Hydraulic drive ensuring smooth, stable, and precise extrusion Heavy-duty, solid construction for long service life Reliable operation, even with demanding rubber compounds User-friendly operation and easy integration into existing production lines Proven Barwell quality, widely trusted in the rubber industry Applications: Extrusion of rubber profiles and semi-finished products Preparation o ...

We can offer 2 twin screw extrusion compoundibg lines,manufactured in 2015 diameter 75mm, L/d 40. water circle pellitzer.drive motor power 160kw.short time working, very good condition.Serious buyers contact us. We have many brands and models machines, tell me what you need seriously!

pdf attached

Material: PE, PP, PS, ABS // Details: DC motor, segmented screws and cylinders, screw speed max. 300 rpm, degassing, vacuum pump, mass pressure and mass temperature sensors, strand head, control cabinet for heating and motor control. Screw Ø: 2x 67 mm L/D: 34:1 Motor: 97.5 kW (DC)

Stock No. 2590k 1 used compounding pelletizing line, throughput up to 1200 kg/h depending on material, consisting of: 1x Grav. Dosing system 5-component SITECOM incl. control 1x Extruder twin screw THEYSOHN type TSK 90 Screws 2x Ø 90 mm – 36 LD synchronization Segment screw and barrel, water / medium cooled Screw speed up to 300 rpm-1 Extruder drive 255 kW-DC 1x side dosing extruder TSD 75 twin screw with drive 3 kW 3x degassing openings 1x melt filter No. 1 type K –HS- Y with sieve 176 mm, incl hydraulic 1x melt pump with drive 22 kW 1x meelt filter No.2 type K-SWE 180 RS back-flush self-cleaning incl. hydraulic 1x strand head with 32 x Ø3.5 mm holes 1x strand cooling pool 620 x 5000 mm 1x string granulator SG 300, drive 11 kW Screen control ResoTec / control cabinet Visit / demonstration at short notice by arrangement. Further compounding lines and access ...

Material: PE, PP, PS, ABS // Details: DC motor, segmented screws and cylinders, screw speed max. 300 rpm, degassing, vacuum pump, mass pressure and mass temperature sensors, strand head, control cabinet for heating and motor control. Siemens Simatic OP17 controller Screw Ø: 2x 75 mm L/D: 36:1 Motor: 143 kW (DC)

Key data: 50

Extruder 2 spindles: 50 mm Ø 12 L/D, motor: 4.5 kw, without electrical panel.

Varex 3-layer blowfilm-extruder Head diameter: 630 mm Screw diameter: 70-90-70 mm( die gap: 2,4) Film width: 1390 – 2580 mm Film thickness: 10-200 my Output: max 480 kg /hour Winding diameter 1200 mm Core diameter 76/150/152 mm Energy: 295 kW/h Treatment: in+outside

Extruder 2 spindles 18L/D, model: BK-50-93, tapered spindles, brand: Volcano, with motor: 25hp, with variable speed drive. Degasser and dispenser of material and electrical panel.

Key data: 130

Extruder 1 spindle : 130 mm Ø, 35 L / D, for grancear plastics, brand: Plasco, with forced feeding. Degasser, with vacuum pump: 15 hp. Filter changer: 260 mm, overhead cut to water. Vibrating screen and motor: 238 KW with variable speed drive and electrical panel. GT-2982

Key data: 60

Extruder 1 spindle: 60 mm Ø 32 L/D, Amut brand, variable speed motor Elektra Faurndau: 7 to 24 KW, with electrical panel and wire head for pellets: 23 holes and electrical panel.

Key data: 120

Extruder 1 spindle for manufacture of pellets. 120 mm Ø, 35 L/D, brand name: FBM ( Falzoni), type: ETF 120 V 380/5L, year: 1988. Engine: 200 KW. Degasifier and filter changer. Head cut under water, year: 2006, brand: PRT and force-feeding silo.

Key data: 120

Extruder 1 spindle: 120 mm Ø, 35L/D, brand: Union, with degasser, hydraulic filter changer: 150. Year: 1987.

Key data: 50

Extruder 2 corrotating spindles: 50 mm Ø, 40 L/D, brand: ICMA SAN Giorgio, with double degasser. Motor: 57.5 Kw direct current with drive. Material dispenser and thread head (spaghetti), with electrical panel.

Key data: 60

Extruder 1 spindle: 60 mm Ø, 25 L/D, brand: Safinio, motor: 20 hp, variable speed drive, brand: Omron, model: F7, alternating current: 30 kw and electrical panel.

Key data: 120

Extruder 1 spindle : 120 mm Ø 35 L/D, make: Union, motor: 110 Kw (150 hp). 4.2 m. long. With degasser, filter changer: 220 mm, overhead cutting to the water with centrifuge and screen. Electrical panel with variable speed drive.

Stock No. 2680 1x partially overhauled and functionally tested Compounding extruder double screw, co-rotating intermeshing Segmented screws and cylinder barrel (water cooled) Screws 2x 64 mm - 40 L/D Screw speed up to 1200 rpm-1 Drive 482 kW-DC Gearbox Flender safety coupling atutomatik 3x degassing venting ports ( vacuum pump optional for extra charge ) 2x side feeding dosing extruder type ZSFE 50 twin screws with dm 48.5 mm with 4 kW each, speed up to 800 rpm.-1 Control cabinet with Siemens HMI Touch OPTIONAL at extra cost: 1) Screen-pack-changer changer 2) Vacuum pump 3) Pelletizing: ST strand, - WRG waterring or - UWP underwater pelletizing system 4) Granulate classifying sieve 5) gravimetric loss-in-weight blender / dosing system 6) Material conveying 7) Big-bag filling station 8) Start-up by our technicians Visit to our factory in Wuppertal.  ...

Key data: 90

Extruder 1 spindle Brand: Eurotecno, 90 mm Ø, 33 L/D. Electrical panel, filter changer: 160 mm, wire head for graining, stainless bathtub: 3 m, without motor. Eurotecno noodle model G-400 with blades: 300 mm.

in very good working condition

Single screw Extruder Theysohn 63mm

Key data: 65

Extruder 2 corrotating spindles: 65 mm Ø, 30L/D, brand: Maris, model: TM-65 V. Shirt and spindle compatible by segments. Degasser, motor: 90 KW DC, with variable speed. Thread head and 2 spare spindles.

Compact cascade extruder - 1x extruder with 80 mm screw diameter - 1x extruder with 70 mm screw diameter - Vacuum degassing or atmospheric - Control cabinet / control for both extruders - Extrusion nozzle

Compounding - granulation line, consisting of: Extruder twin screw synchronization, drive 31 kW Segment screws and barrels, water-cooled Screws 2x Ø 35 mm – 44 L/D 1x degassing zone (atmospheric) 1x degassing zone (vacuum) 1x side dosage Screen changer double piston type K-SWE 101 with hydraulics Switchboard Water bath, granulator, etc. optionally also available on request.

Francis Shaw 30mm Extruder Roller Feed LD ratio 15:1 Year 1993

Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009

Key data: 2 mm

CPP 7 ply , Testline, can also be used for smaller special productions. Film width max = 650 mm, Output max. = 200 kg/h Nozzle width = 800mm 5 Extruders: 2x Ø 60mm, melt pumps available 70 kg/h each 3x Ø 38mm 19 kg/h each Output: 200 kg/h Weight range: 50-700 μm, Hopper and pneumatic conveying option! Cloeren Feedblock EDBBCAA EBBCDCA ACEDEBA Cooling roller unit with 3 rollers Rewinder diameter max = 300 mm

Key data: 130 mm, 35 , 600 U/min

Material: PE, PP, PS, ABS Details: DC motor, segmented screws and barrels, screw speed max. 300 rpm, degassing, vacuum pump, mass pressure and mass temperature sensors. Control cabinet for heating and motor control (NEW. Siemens S7) Screw Ø: 2x 130 mm L/D: 35:1 Motor: 500 kW (DC) Optional: side feeding, screen changer, GALA underwater pelletizing

Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel

Key data: 40 mm, 40 , 600 U/min

Material: PE, PP, PS, ABS, Year of construction: 2000 Capacity: approx. 100 – 300 kg/h Screw diameter: 2 x Ø 40.0 mm L/D: 40:1 Propulsion: 110 kW (DC) more details: synchronous, degassing with vacuum pump, screws and cylinders segmented, Strand nozzle, water bath, strand granulator. NEW control cabinet for heating and motor control (Siemens S7, touch screen) Optional: Side loading

Used Cincinnati conical twin-screw extruder model CMT 35. 2 pieces available: 1 pc. - new 1989 1 pc. - new 1990 Technical data: - drive: DC 9kW motor - heating zones: cylinder - 3, head - 3 - cylinder cooling - oil - vacuum degassing pump

Key data: 65

Extruder 1 Screw 65 Ø diam, 30 L/D Brand: Flag engine: 30 KW (40 hp). With electrical panel. Reference: GT-4706

The winder is part of a cast film system and is in good condition. Max. foil width = 2350 mm Max. roll width at inlet = 2600 mm, Max diameter roll = 980 mm Sleeve size 3", 6 Film thickness= 15 – 200 my, Max. speed = 250 m/min Edge trimming with razor blades, The winding can be in contact or gap Automatic loading of 3 inch sleeves from the sleeve magazine. Automatic unloading of the finished roll by means of a robot.

Key data: 17 mm, 40 , 1200 U/min

Kategorie / Category: Twin-screw extruder / Twin-screw extruder Nummer / Number: DE27684 Manufacturer / Manufacturer: Leistritz Typ / Type: ZSE 18 HPe Baujahr / Year: 2009 Capacity: approx. 40 - 60 kg/h Motor: 9.4 kW AC max. screw speed: 1,200 rpm Screw diameter: 2 x Ø 18.8 mm L/D: 40:1 Material: PE, PP, PS, ABS + fillers // more details: synchronous, atmospheric degassing, segmented screws and barrels // Control: MacromateXX Siemens with visualization //

Key data: 60

Extruder 1 screw: 60 mm Ø, 25 L/D, brand: Flag, motor: 11 KW (15 hp). 6-speed gearbox with electrical panel. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice.

Key data: 63 mm, 1300

Twin screw extruder, conical Manufacturer: Reifenhäuser Type: BT 1000-2-63 K Year of Make: 1994 Machine No.: 32061 Working hours: 32,303 h Screw geometry: conical for PVC-hard profiles Screw diameter: 63 – 121 mm Screw length: 1300 mm Screw speed: max. approx. 32 1/min. Nominal torque of the gearbox: 1000 daNm Dynamic load rating of the return pressure bearing: 103600 daN Engine power: 43.0 kW, Drive motor: Baumüller DC motor Cylinder heating/cooling zones: 4/3 (air cooling with fan) Adapter heating zones: 1 Tool Heating Zones: 5 Temperature control: digital temperature controller (2 x PSG Multipact 88) Max. permissible mass pressure: 500 bar Output capacity: approx. 150 - 200 kg/h for PVC-hard profiles Accessories: Dosing device and material hopper Extrusion height: 1150 mm Dimensions: 4250 x 1200 x 1750 mm without hopper (LxWxH) Weight: approx. 3000 kg Cond ...

Key data: 50 mm, 30

Used extruder in good condition with screw size: diameter 50 mm x 30v grooved intake and degassing zone Type RH 241-1-50-30v with DC drive 30.2 kW Built in 1993 Immediately available without control cabinet With control cabinet 4-6 weeks delivery time

90s cold feed extruder, GE 90 x 16 D Vac, make Troester, with large hose / profile spray head, drive 52 KW Siemens AC, 4 TCU Siengle

Key data: 35 mm, 25 , 107 U/min

used REIFHÄUSER single screw extruder with screw size: diameter 35mm / 25 ld The extruder is in very good condition Type RT 78-1-35-25 New control cabinet with new motor AC -7,5kW Year of construction 1994 Quickly available

Key data: 50 mm

50mm Extruder Manufacturer: Rutil Screw diam. 50mm LD ratio 15:1 Max speed (50 Hz) 70rpm

Extruder 1 screw: 70 Ø diam, 35 L/D. Brand: Flag, engine: 37 KW (50 hp). No electrical panel. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice.

cold feed extruder - 60 mm x 18 D vacuum, with feed roller, drive 22 KW, screw speed 10 to 60 rpm, with gear pump, 5 TCU,

1 Screw Extruder for Sale Brand: Maquiplast Diameter: 80 mm Ø L/D ratio: 20 L/D Engine: 30 kW (40 hp) Variable Speed Drive: Delta For more details or to make an enquiry, please contact us.

cold feed vacuum extruder Troester 90 mm x 18 D, with feed roller, drive 46 kW, pie speed 10 to 60 rpm, 5 TCU,

120 mm cold feed pen convert-extruder, GE 120 SC, make Berstorff, output capacity up to 1,000 kg /h as a power extruder with strip spray head, complete rebuild mechanically and electrically in 2024

Key data: 45 mm, 1350 , 298 U/min

Single Screw Extruder Cincinnati Talos 45-30 G Year of construction 2009 + Corrugator Maintools MTC 60/90 Year of construction 2006 Both machines are in good condition, and immediately available

Key data: 75 1/min

This WEBER extruder is in machine storage at Plastima Used Machinery. The machine comes from 1997 and is in great condition. Brand: Hans Weber GmbH Model: NE 7 042 Type screw: single screw Year of construction: 1997 Screw Ø: 75mm Working hours: 58.668

- Ø 45 mm - 28 L/D - No motor and no frame

Z Blade Stainless Steel Mix Extruder Manufacturer: Winkworth Model: 14Z HMX Working capacity 22-25 litre Approx total volume of trough litres: 32 litre with Hasco Hydraulics Ltd power pack With Panel YOM Jan 89

DC motor Stromag 70 kW, gearbox 2 x 960 Nm, with Coperion ZSB 70 side feed. The worm shafts and the end head are missing. Therefore, sales as spare parts carriers.

Z Blade Mix Extruder Manufacturer Winkworth Model 31Z HMX Mild Steel Total volume 360 litre Working capacity 250 litre Internal dims: 740mm long x 790mm wide x 714mm deep Screw 220mm With oil jacketed trough Lagged and with 3x electric drives

Description Single Screw Extruder Screw diamter 60 L/D 25 Motor power 27,5 kW

AST 220 / POMINI-FARREL flat head / POMINI-FARREL 18"x15" Slabber / BANDERA Slabber. Refer to code 1043-1044-1045-1046 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Description Conical Twin Screw Extruder Screws Diameter 45 - 97 Screws Length 390 Barrel zones 3 Nr.1 vent Thermoregulated screws Motor power 15,4 kW Forced feed

Description Conical Twin Screw Extruder screw diameter 80 Thermoregulated screws 1 vent Installe dnew lectrocal motor in 2018 Unstalled new inverter for electrical motor in 2018 Motor power 68 kW Retrofit of PLC with BCtouch control

Key data: 215 mm, 304

Pomini 12” x 8.5” Dump Extruder Type 12/8.5 Year of Manufacturing: 1993 Conical screw 300mm 215mm diam. Pneumatic crammer feed with DC variable speed motor Pelletizing head Without controls

Control panel: Siemens SIMATIC HMI, connected load: 80kW, weight: 1.85t, operating hours: approx. 4500h, with Kreyenborg feed hopper, year of manufacture: 2017, and Trendelkamp screen changer. Documentation is complete, on-site inspection is possible.

DL-2400 THREE LAYER CASTING MACHINE

90 mm Extruders Machine, 2024 Model Gearbox: YRE2430XEİ: 18.67 Motor: Gamak brand, 30 kW, 1470 RPM Transmission: Belt / Pulley Overall Dimensions: 2700 mm / 1500 mm Production: Made in Turkey, 2024

EX-225 L/D 1600/225 Extruder Gearbox: Farrel Motor: Gamak brand, 110 kW, 1480 RPM No TCU No Control Panel Transmission: Belt / Pulley Dimensions: 4000 / 1800 / 2500 mm Production: Made in USA Extruder with Hot Feed

EX-120 L/D:1600/90 Gearbox: Leyond Motor: Gamak, 37 kW, 1475 RPM TCU: None Control Panel: None Transmission: Belt - Pulley Overall Dimensions: 2700 x 1800 x 1500 mm Production: Made in ENGLAND

L/D : 1500/90 REDUCTOR LEYOND MOTOR : VEM MOTOR 1470 D/DK 1 UNIT TCU NO PANEL BAND PULLEY TRANSMISSION GENERAL DIMENSIONS: 2300 1500 1900 ORIGIN: ITALY

WELEX SHEET CO-EXTRUSION LINE, running with ABS and PS, extruder 115 mm screw diam. 30 L/D, degassing system, 225 kw drive, 190 rpm screw speed, hydraulic screenchanger, hydraulic pack and accumulator, Maag gear pump 56/56, water cooled, gravimetrical blenders, Motan dehumidifying dryers, + Covema co-extruder with 60 mm screw diam. 24 L/D, 175 rpm, electrically heated, air cooled barrel, 18,5 kw drive, 1.650 mm EDI R75 ultraflex die., Flex range on the top lip of up to 1.9 mm. Mounted gap is ca 2.6 mm., Bottom lip is removable and has slotted bolt holes, adjustable to achieve a wider thickness range., One spare bottom lip available - thickness to be checked, 1650 x 400 mm Ø rolls, Static mixer, ABA co ex block with plate type inserts, 1.650 mm 3 roll polishing stack model 18x65 LHSL. 450 mm diameter rolls. Chain driven through selector gearbox. circa 5 hp dc motor. Upstack configuration ...