sml 押 出 機 中古 販売のため

The extrusion line was designed for cast film production. Processing of thermo plastics in a temperature range of 150-300°C. POSSIBLE LAYER STRUCTURES: - mono film
 - 3- layer (A-B+C-A) - 5- layer (A-B-C-B-A) DATA OF FACILITY Total output of extruders max. 2230 kg/h Extruder A: 90/33 L/D max. 330 kg/h Extruder B.: 135/33 L/D max. 950 kg/h Extruder C.: 135/33 L/D max. 950 kg/h Film width range (net): 1600 - 2110 mm Two rolls cutting possible (2x 800 – 2x 1055mm) Thickness range: 25-580μm Production speed: 10 - 150m/min Roll width: 2500 mm Max. roll weight: 2000kg ADDITIONAL COMPONENTS (QUALITY): Non-contact thickness equipment for automatic TD profile measurement with double side corona treatment (max. 12000W) Optical inspection system, including marker system if failures are detected, incident and transmitted light system  ...

The original part is a main and KO extruder from Kuhne built in 2006, the system was extended in 2010 by an additional extruder from the SML (coating unit). Plant description: COEX cast film line with additional coating unit. The main plant is equipped with a co- and a main extruder. The coating unit with a main extruder. Processing of thermoplastics in a processing range of 90-300°C. The system can be operated with the following combinations: • Main unit (CoEx system) with coating unit • Main unit (CoEx system) without coating unit • Only coating unit with unwinding unit for carrier film For operation in the various combinations, the corresponding additional units are switched on or off. Possible layer structures: Main plant: - Monofilm with release film if required - 3-layer film (A-B-A) with release film if required Coating: - Monofilm on carrier material if req ...

The winder is part of a cast film system and is in good condition. Max. foil width = 2350 mm Max. roll width at inlet = 2600 mm, Max diameter roll = 980 mm Sleeve size 3", 6 Film thickness= 15 – 200 my, Max. speed = 250 m/min Edge trimming with razor blades, The winding can be in contact or gap Automatic loading of 3 inch sleeves from the sleeve magazine. Automatic unloading of the finished roll by means of a robot.

The extrusion line is a COEX cast film line. Processing of thermoplastics in a processing range of 150-300°C. Possible layer structures: - Monofilms - 3- layer (A-B+C-A) - 5- layer (A-B-C-B-A) Plant data: Total system output max. 2230 kg/h Extruder A: 90/33 L/D max. 330kg/h Extruder B.: 135/33 L/D max. 950kg/h Extruder C.: 135/33 L/D max. 950kg/h Film width NET: 1600 - 2110mm; Center cut for 2 bobsleighs possible (2x 800 – 2x 1055mm) Thickness: 25-580μm Production speed 10 - 150m/min Roll width 2500 mm roll weight 2000kg Additional components (quality): non-contact thickness gauge for automatic nozzle with automatic cross profile control on both sides Corona pretreatment (max. 12000W) Optical surface inspection system incl. defect marking in open and pass-through light Ancillary equipment: Dryer 1 – 4 with 4500 liters volume ; Heating capacity 48kw dryer 5 ...

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

This shredder has a large diameter rotor (30 cm) and 12 rotating blades. The motor has an output of 4 kW. This shredder is equipped with a torque increase gear (reducing gear), so it is also suitable for shredding thicker plastic waste. The grid is interchangeable, so the grain size can be changed. Everything works fine, motor, bearings, gearbox, rotor, blade are all fine. It can be used immediately. I have several of them. Other shredders are also for sale. Please see my other ads.

This grinder has 2 fixed knives and 15 rotating blades. The motor power is 2.2 kW. The grid is replaceable, so the grain size can be changed. Everything works perfectly, motor, bearings, rotor, knife are fine. It's ready to use. I have several of them. There are also other document shredders for sale. Please also see my other ads.

This grinder has 1 fixed blade and 3 rotating blades. The motor power is 2.2 kW. The grid is replaceable, so the grain size can be changed. Everything works perfectly, motor, bearings, rotor, knife are fine. It's ready to use. I have several of them. There are also other document shredders for sale. Please also see my other ads.

Guillotine-type mechanical shear for cutting plastic sheet in industrial processes. Brand: Jwell Cutting width: 1440 mm Maximum thickness: up to 6 mm Geared motor: 7.5 hp (5.5 kW) Type: Mechanical Guillotine Applications: - Cutting rigid or flexible plastic sheet - Post-process extrusion - Plate and film production - Preparation for thermoforming