Виробник:
(Категорія: 107)
ширина листа: 3100 ммтовщина пластини: 10,00 ммвідстань між колонами: ммзагальна потреба в потужності: кВтВага машини приблизно: 10,00 тРозміри машини бл.: мМоторизований задній упор до 1000 мм з цифровим дисплеємБічна огорожа та подовжувачі столуОбмежувач довжини різуОсвітлення краю різуПримітка: Задній упор трохи неточний (+/- 1 мм)Дані для цієї реклами були створені за допомогою ModulMWS - програмного рішення LogoTech oHG.
sheet width: 2050 mmplate thickness: 2 mmstrokes per minute until: 38 cutting angle: 1,75 °table height over floor: 870 mmtotal power requirement: 3 kWweight of the machine ca.: 1520 kgrange L-W-H: 2,2 x 0,6 x 1,2 mElectric 380 Volt: Back stop with manual adjustment: Shadow line lighting: Foot switch: Demo machine at a special price: The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with astandard geared brake motor via a chain connection to the main axle. theknives are of the highest quality. The optimal cutting angle secures thetogether with the sheet holder perfect cuts.Bearings and guides are maintenance and lubrication-free.Standard equipment: • Back gauge 665 with mm scale. •cutting edge lighting. • Section counter. • Table extensions 600 mm. •Right angle stop, left. • Movable 24 V foot switch with em ...
sheet width: 2020 mmplate thickness: 2 mmdaylight upper clamping: 122 mmbending angle max.: 135 °range L-W-H: 2,56 x 0,6 x 1,26 mweight of the machine ca.: 1020 kgUnused exhibition machine at a special price:Segmented top rail for bending box profiles, upper beam clamping hand-operated,manual bending beam actuation with weight compensation, degreescale, adjustable bend stop. Warranty = 12 months for single-shift operation.The bending performance refers to 380 N/mm² strength. Plus freight + packaging 270,--.To complement this, we have a Kapema motorized panel shear, model SMP 20/20, capacity 2050 x 2 mm with manual backgauge, cutting line lighting, etc. Pleaseinquire if you are interested.This is an exhibition machine at a special price, so we are selling it without any warranty.Machine. Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the softw ...
sheet width - max.: 1010 mmplate thickness: 4.0 mm STplate thickness: 2.5 mm VAplate thickness: 6.0 mm ALUnumber of strokes - loaded: max. 20 Hübe/mincutting angle: 1.5 °work height max.: 900 mmControl: ELGO total power requirement: 5.5 kWweight of the machine ca.: 2200 kg. from a maintenance workshop good condition ()Equipment:- Robust NC electro-hydraulic guillotine shear- NC electro-motorized backgauge Includes NC ELGO positioning control TYP 85- Electric cutting length limiter- Manual cutting gap adjustment- 1x side stop with scale- 2x support arms- 1x freely movable foot switch- Original operating instructions Special accessories included:- Pneumatic holding device for thin sheet metal blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 60 tchamfer lenght: 2050 mmdistance between columns: 1550 mmthroat: 255 mmstroke: 165 mmdayligth: 475 mmworking feed: 9,8 mm/secreturn speed: 117 mm/secajustment speed: 150 mm/sectotal power requirement: 5,5 kWweight of the machine ca.: 5000 kgdimensions of the machine ca.: 2300 x 1500 x 2470 mmEquipment:- DELEM DA65 CNC control- Electric backgauge (X-axis), 600 mm- Hydraulic upper tool clamping- Front light barrier- Side and rear protective grilles- Manually adjustable stop bar, foldable (R+Z-axis)- Upper tool- 2x support arms- Machine feet- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Ширина листа: 750 ммДовжина пластини: 1250 ммТовщина пластини: 4 мм Площа поверхні: 1600 х 1050 ммно. ударів: 180 Вт/хв. Діаметр штампування: 105 мм Тиск штампування: 25 тЗагальна потреба в потужності: 4,0 кВт Вага машини приблизно: 1,8 Розміри: 1,9 х 1,9 х 1,7 мМашина для штампування та нарізування- Цифрове зчитування для осі X та Y- Інструментальна шафа з інструментамиДані для цієї реклами були створені за допомогою ModulMWS - програмного рішення LogoTech oHG.
ширина листа: 1020 ммтовщина пластини: 2 ммвідстань між колонами: 1020 мм кут згинання макс.: 135 загальна потреба в потужності: 0 кВтвага машини приблизно: 0,3 трозміри машини бл.: 1350 х 850 х 1175 мМакс. кут згину 135Ручний привід з додатковою пружиною з обох сторін. Отвір верхньої балки 40 мм, верхня і нижня балки сегментовані, поділ сегментів: 25-30-35-40-45-50-75-100-150-200-270 мм. Дані для цієї реклами були створені за допомогою ModulMWS - програмного рішення компанії LogoTech oHG.
sheet width: 3000 mmplate thickness: 6 mmdistance between columns: 3200 mmspeed: . m/minrear stop: 1000 mmtotal power requirement: 7,5 kWweight of the machine ca.: tdimensions of the machine ca.: mThe backgauge is electric.The technical data is provided by the manufacturer or operator and is therefore non-binding. We reserve the right to sell the machine prior to sale, our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in stockOver 15,000 m² of storage space, 70 t crane capacityMore than 10,000 items and accessories for your workshopIf you are interested in selling machines, production lines, or your business,please contact us.You can find further offers on our website.Tours are possible by appointment.We look forward to your visit.Your Markus Hirsch TeamThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
товщина пластини: 4 мм Товщина пластини: 3 мм Довжина леза: 225 ммПотужність двигуна: 3,5 кВтвага машини бл.: 650 кгРозміри машини бл.: 1250 х 900 х 1100 ммОсобливості:- 2x кутові упори- 90 з фіксованим кутом- Ножний перемикачДані для цієї реклами були створені за допомогою ModulMWS - програмного рішення LogoTech oHG.
sheet width: 1360 mmplate thickness: 06,0 mmdistance between columns: mmtable width: 455 mmwork height max.: 880 mmcutting angle: 1°30 °rear stop: 750 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 3050 mm: 12,0 mm: -: 0,5-3,0 °: 1000 mmtable height: 930 mmwork height max.: 930 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 1000 mmy-хід: 600 ммz-хід: 600 mmкерування: Heidenhain TNC 426 шпиндельний ніс: 100-700 ммробочий стіл:: 1.080 x 580 мм.вага заготовки макс.: 550 кгT-слоти: 7 Stk.T-слот - ширина: 14 ммінструмент Магазин з: 36 Плеценвага інструментів макс.: 8 кгдовжина інструменту - макс.: 340 ммзагальна потреба в потужності: кВтвага машини приблизно: 6,2 трозміри машини бл.: 4,790 x 5.330 x 2.905 мм. Дані для цієї реклами були створені за допомогою ModulMWS - програмного рішення LogoTech oHG.
sheet width: 3050 mmplate thickness: 6.0 mmcutting angle adjustment: 0.5 - 3.0 °down holder: 18 Stückno. of strokes: 8 - 14 Hub/minback stop - adjustable: 750 mmwork height max.: 770 mmControl: SP 8 total power requirement: 7.5 kWweight of the machine ca.: 4800 kg.range L-W-H: 3650 x 2100 x 1750 mm very little use () from a maintenance workshopFeatures- Guide-railed electro-hydraulic guillotine shear- HACO control model NC SP 8 Easy operation directly at the cutting table Adjustment of cutting angle + backgauge Retraction function from rear stop Electric cutting length limitation Emergency stop button, locking - Motor-adjustable and programmable rear stop- Electric/hydraulic cutting angle adjustment- Manual cutting gap adjustment, from the front- 1x side stop - 1,000 mm, with scale & T-slot- Front finger guard- 1x freely movable foot switch- Rear safety guard + sheet metal chute- Ope ...
ширина листа - макс.: 300 ммтовщина пластини: 8 ммплоска сталь: 80 х 10 ммдовжина леза: 300 ммдовжина машини: 860 ммвисота машини: 565 ммвага машини приблизно: 172 кгДилер довгих вимірювальних ножиць з власним запасом 1600 м². Дані для цієї реклами були створені за допомогою ModulMWS - програмного рішення компанії LogoTech oHG.
товщина пластини: 4 мм Товщина різання макс. При (60 кг / мм²): 3 ммДовжина леза: 90 ммВага: приблизно 30 кгРозміри машини приблизно: 0,45 х 0,30 х 0,2 мЗубчастий блок для установки під гідравлічний або ексцентриковий прес. Товщина різання оцінюється як невелика. Дилер машин з власним складом 1600 м². Дані для цієї реклами були створені за допомогою ModulMWS - програмного рішення компанії LogoTech oHG.
pressure: 220 tchamfer lenght: 3720 mmdistance between columns: 3020 mmcolumn arm: 400 mmajustment speed: 125 mm/secworking feed: 10.0 mm/secreturn speed: 132 mm/secback stop - adjustable: 800 mmstroke: 275 mmdayligth: 550 mmtable height: 900 mmoil volume: 300 ltr.total power requirement: 18.5 kWweight of the machine ca.: 12800 kg.range L-W-H: 5850 x 2220 x 2820 mm Good condition Current new price approx. 100.000 euros Special price on requestFeatures:- Electro-hydraulic CNC press brake- With DELEM CNC control model DA 66W 2D graphic programming Automatic bend sequence calculation and collision detection High-quality color LCD screen (TFT) - Swivel control panel, front left- CNC-controlled axes: Y1 + Y2 + X + R + crowning - CNC electric motor-driven backgauge (X axis)- CNC electric motor height adjustment of the backgauge (R axis)- CNC electric motor-driven bending table crowning- 2x man ...
ширина листа: 2000 ммтовщина пластини: 3 ммзадній упор: von Hand, 750 ммкількість опорних важелів: 2 Дані для цієї реклами були створені за допомогою ModulMWS - програмного рішення компанії LogoTech oHG.
pressure: 170 tchamfer lenght: 4080 mmdistance between columns: 3680 mmcolumn arm: 410 mmdayligth: 385 mmstroke: 215 mmajustment speed: 200 mm/secworking feed: 1-10 mm/secreturn speed: 135 mm/sectable width: 200 mmtable height: 1050 mmNumber of working hours: 25.430 hoil volume: 350 ltotal power requirement: 29 KVAweight of the machine ca.: 16.450 kg.range L-W-H: 4620 x 2210 x 2885 mm Machine in good condition Regularly serviced by the manufacturer CNC backgauge with 8 axes ()- in checked conditions - machinevideo - https://www.youtube.com/watch?v=yEaRj0XJAC4Equipment:- CNC electro-hydraulic press brake/die bending press- DELEM CNC control - swiveling front left High-resolution graphic screen Clear, concise menus in the operators language Large tool and product library Graphic 2D programming Automatic bend sequence calculation and collision detection Emergency stop button at front - CNC ...
pressure: 170 tchamfer lenght: 3170 mmdistance between columns: 2700 mmcolumn arm: 420 mmdayligth: 470 mmstroke: 200 mmajustment speed: 100 mm/secworking feed: 10.0 mm/secreturn speed: 100 mm/sectable width: 180 mmtable height: 960 mmoil volume: 235 L0: 300 barcontrolled axis: 6 AnzahlNumber of working hours: 29.400 htotal power requirement: 16.5 KWweight of the machine ca.: 11910 kgrange L-W-H: 4025 x 2020 x 2900 mm well-maintained condition () with only approx. 29.400 operating hours- in checked condition - machine video -https://www.youtube.com/watch?v=APP0HZjMms4Equipment:- electro-hydraulic CNC press brake- AMADA CNC control OPERATEUR 2 - 6 axes (X, Y1 + Y2, R, Z1 + Z2) swiveling operation - front left tool & program library- CNC-controlled back stop adjustment (X-axis) adjustment range .. 700 mm- CNC-controlled vertical adjustment of the stop fingers (R-axis) adjustment range .. 25 ...
: 1550 mm: 2,0 mm: 1,5 mmroll diameter: oben 90 mm: 560 kg: 2580 x 700 x 1250 mm mm- 2 central rollers driven by an electric motor- Swing-out upper beam- Conical bending device- separate control panel- self-braking main motor- CE mark/Declaration of ConformitySpecial equipment included in the price:- hardened rollers- Motorized rear roller adjustmentThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 2.00 mmthickness at Niro-steel: 1.25 mmno. of strokes: max. 36 Hub/mincutting angle: 0.9 Gradtable height: 800 mmtable width: 430 mmdistance between columns: 3200 mmback stop - adjustable: 5.0 - 750 mmControl: konv. engine output: 3.0 kWweight of the machine ca.: 1950 kgrange L-W-H: 3730 x 2070 x 1400 mm Original price approx. 45.000 euros () Special price on requestFeatures:- Robust / motorized swing-cut guillotine shears- Machine with manual material/backgauge Travel range 5.0 – 750 mm stop depth Analog position display Manual adjustment from the front - Break-proof, torsion-free steel welded construction- Compact and clear machine design- 1x hold-down beam Hold-down opens before the knife beam moves up No kinking of very sensitive sheets- Manual cutting gap adjustment- Integrated sheet metal holding system for thin sheet metal cuts- Sheet metal ...
sheet width: 1020 mmplate thickness: 1,5 mmdaylight opening: max. 85 mmweight of the machine ca.: 240 kgdimensions of the machine ca.: mSmallest bending width factor 10 x sheet thickness s Smallest inner radius factor 1.5-2 x sheet thickness sLowering capability of the lower and bending beams 20 mmOn this swing-beam bending machine, the beams and side stands are reinforced with particularly strong ribbing. The cross-sections are designed to be strong enough to bend even narrow offsets. On the AML 1000 model, the bending beam is balanced by a gas pressure spring.The opening width of the upper beam and the lowerability of the lower and bending beams are generously dimensioned.The machine is being sold as defective because the connection between the lower frame and the right side stand is broken (see photo taken from behind)!The data for this ad was created with ModulMWS - the software sol ...
blade length: oben 211/unten 180 mmplate thickness: max. 6 mmround bar steel: max. 13 mmweight: ca. 19 kgSturdy shears body of quenched and tempered steel. Moving blade guides free of play (with low friction losses), blades of special tool steel, specially hardened and ground. Lever arm with counterweight spring for protection in the event of accidents, all pivot pins adjustable, all models with steplessly adjustable clamping arm.With compound action. Cuts sheet metals and round steel bar.Colour: Red-brownThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tube diameter: 48,3 mmwall strength: 3,25 mmbending radius min.: max. 180 mmBending speed: 20 °/sectotal power requirement: 2,4 kWweight of the machine ca.: 700 tdimensions of the machine ca.: 3880 x 800 x 1250 mDescription:Round tube steel (S235): 60.0 x 6.0 mmRound tube stainless steel (S 355): 60.0 x 4.0 mmSquare tube steel: 50 x 50 x 4.0 mmRectangular tube steel: 60 x 40 x 2.0 mmmax. usable length: 3048 mmBending speed: 10°/secincluding tools (see photos)Mandrel is no longer available, can be retrofittedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
