б/у
подержанный транспорт коробки Сделать KHS 18 м прямой транспортер 240,---м/м 2 части 90 кривых без привода 450,-" несколько станций привода/отклонения 650,-» Различные перила кронштейны с направляющими
Overview This KHS Innoclean single-end bottle washer for returnable glass bottles was built in 2007. It cleans and de-labels empty bottles before filling: bottles are pushed into carrier-basket cells, run on heavy roller chains through a pre-soak, two pre-warming baths, the main caustic soak with under- and over-caustic label flushing, and three water spray zones, then handed back onto the bottle conveyor at discharge. Nineteen bottles run across the machine width in 4,275 cells; output range and design output are given below under Technical data. At design output, total dwell time is 18.7 minutes, including 10.8 minutes of caustic contact. KHS modernised the drive and operator station in 2022: Triple-i-Drive and a capacitive multi-touch panel with RFID login, detailed under Equipment. A KHS manual supplement dated November 2022 covers the upgrade. Technical data Manufacturer: KHS Model: ...
Overview This KHS Innopas P II SG 30-200 is a tunnel pasteurizer for bottled beverages in glass bottles, built in 1996 by KHS (Klöckner Holstein Seitz, Germany). With a treatment area of 113.5 m² across 8 treatment zones (3 of them recuperative), it pasteurizes at approx. 24,000 - 25,000 bottles per hour depending on bottle format, at a maximum pasteurization temperature of 75 °C. For 0.7 l glass bottles the total treatment time is approx. 48.6 minutes (21.2 min heating, 12.3 min pasteurization, 15.0 min cooling) at approx. 5 pasteurization units. The main control is a Siemens SIMATIC S5 PLC; the pasteurization unit setting (temperature diagram) was later upgraded to a Siemens S7 with touch panel. Danfoss frequency drives are fitted. The machine ran at a German mineral water bottling plant until mid-2024 and is now completely dismantled and professionally stored, with the conveyor bel ...
Glass bottle filler and capper with short-tube filling valves for level filling (measured filling) of bottles. The bottles are pre-evacuated (11 kW vacuum pump from GEA Ahlborn). The pinion control system was replaced in 2025. As part of this, all pinions were also replaced. The air ring for the lifting cylinders of the filling mechanisms was replaced around 2023., Additional title: Short-tube filler with pre-evacuation and crown cap sealer, Capactity: 44000 bo/h, Number of filling valves: 90 pcs., Number of capping heads: 15 pcs., Formats: 0,5 l NRW bottles; crown caps, Material: housing and contact surfaces from stainless steel, Base construction: caroussel-type filling and capping block, Features: filling carousel with 90 short-tube filling valves; crown cap sealer with 15 sealing heads; vacuum pump; bottle and cap rinse; bottle conveyor with drives and format components; protective h ...
Used Used PET KHS Labeller 15.000 bph: Year: 2002 Condition: As Is Model: ROLAND 10HS Year: 2002 Speed: 15.000 bph Rotary Direction of rotation: Counterclockwise ? from right to left 10 plates 1 hot glue station Types of applicable labels: ? Wraparound label Electronic cam Safety protections Machine layout Code: EA 673 More details: https://bottlingscout.com
Used Used KHS labeller: Year: 2007 Condition: As Is Model: SE 2080 ? 145 2KL RF Year: 2007 Speed: 45.000 bph Rotative clockwise direction 40 plates with electrical cam 3 cold glue station for front, back, and neck label 1 rollfed-hot glue station for wrap around label Mobile groups Automatic film reel change on each roll fed station Automatic magazine for paper label Safety protection Code: EA 685 More details: https://bottlingscout.com
Overview This complete automatic can filling line has a nominal output of approx. 20,000 cans/hour for 330 ml cans (can type 211/202), packed 24 cans per foil-shrunk tray. The core is an O+H / KHS Hansacan filler with 30 filling valves, mechanically blocked to a Ferrum F 505 G seamer with 5 seaming heads. Empty cans are supplied by a TMG Impianti Vega 120/B depalletizer and rinsed on a Hysek Rinsstar 20000 rinser before filling. A date/coding printer is not included. Technical data Line type: Complete automatic can filling line Nominal output: approx. 20,000 cans/hour (330 ml), product- and temperature-dependent Container: 330 ml can, can type 211/202; 24 cans per foil-shrunk tray Controls: PLC Siemens S7, Siemens SIMATIC HMI Warmer and drying station reconditioned; fill-height control and packaging machine new Equipment Can Depalletizer | TMG Impianti | Vega 120/B | tier-sheet removal, ...
Overview This O+H / KHS Hansacan can filler, blocked with a Ferrum can seamer, is a rotary can filling and seaming monoblock for beverage cans. Filler and seamer are joined as a single unit, so cans run from filling straight through to seaming in one continuous flow. The block is set up for standard 330 ml cans (can type 211 / 202) and reaches a rated output of approximately 20,000 cans per hour, depending on product and filling temperature. The block was previously in production in a commercial brewery filling 330 ml cans and is currently at the workshop undergoing a complete reconditioning before delivery. Filling parameters and production data are managed via a Siemens SIMATIC touch HMI, with machine control on a Siemens S7 PLC. Technical data Manufacturer: O+H / KHS Model: Hansacan can filler Seamer: Ferrum can seamer, F 505 G Year of manufacture: filler 1992, seamer 2010 Machine typ ...
Overview This carbonator was manufactured in 1992 by Germany KHS. The KHS CX 30 is designed for the production of carbonated mineral water. The unit was upgraded by KHS in 2014 and has a capacity of up to 30,000 litres per hour. The machine was in production until March 2025, was dismantled in December 2025, and is currently stored in a warehouse in Bippen. The machine is available immediately. Technical data Capacity: 30,000 litres/hour Application: Carbonated mineral water Configuration: Carbonator with pumps, tank, and accessories CO₂ rate: max. 8 g/litre Drive: Siemens S7 Scope of Delivery Carbonator | KHS | CX 30 | 1992 (upgraded 2014) | Complete system Pump system Tank | KHS Control system | Siemens | S7
Overview This isobaric beer filler was manufactured in 2002 by German company KHS. The machine is configured for 500 ml glass bottles with crown cork and achieves a capacity of 44,000 bottles per hour. It was used for filling beer at 10–12 °C. The machine will be available from November 2025 and remains installed until then. A site inspection can be arranged upon request. Technical data Capacity: 44,000 bph (500 ml glass bottles) Formats: 500 ml glass bottles Filling principle: Isobaric (mechanical filling system) Number of filling stations: 144 Crowner: 24 stations (crown cork) Operating voltage: 400 V Frequency: 50 Hz Control system: Siemens S7-400 Control cabinet: Air-conditioned, stainless steel Operating hours: approx. 30,000 (as of Nov. 2024) Direction: Left to right Scope of Delivery Filler: KHS Innofill DMG SVF 144-KK24 Crown corker with 24 stations Control cabinet and ope ...
Overview This cold glue labelling machine was manufactured in 2004 by German company KHS. The machine was running until January 2025 and is now stored in the company. The labeller has a camera system for the orientation of the labels in the neck area for swing-top glass bottles. Technical data Capacity: Up to 26,000 bottles per hour Working direction: anticlockwise Formats: 330 ml Longneck glass bottles 330 ml Steinie glass bottles 330 ml Swing-top glass bottles 500 ml NRW glass bottles Label positions: Front (up to 2 labels) Back (up to 1 label) With a Siemens S7 control New HMI touch panel in 2019
for water, lemonades and fruit spritzers. : 0.5 L, 1.0 L, 1.5 L : 24,000 bottles/h (with 1.0 L) (currently only max. 18,000 bottles/h at the packer) The full bottles are packed in PETCYCLE crates. The used bottles that come back with the empties are removed from the crates at the ejector and sent for disposal. (Shredder is no longer available.) The new bottles are destacked pallet by pallet at the new bottle depalletiser and transported pneumatically to the rinser. The system consists of - - Manufacturer: Year of construction: 2001 - Manufacturer: Year of construction: 2001 - Manufacturer: & Year of construction: 1978 with downstream Velcorin dosing system - : - /, / Manufacturer: Year of construction: 2001 with chlorine dioxide and sterile water rinsing - -- Manufacturer: Year of manufacture: 2001 with Alcoa screw capper and liquid nitrogen dosing system - ...
Система очистки и наполнения кегов, включающая конвейер кегов, внешнюю шайбу и ротационную систему для внутренней очистки и наполнения. Дополнительное название: очистка и наполнение, Ёмкость: 60 кег/ч на каждый, 50 л, эксплуатация / управление: Siemens S7-300, Особенности: ротационный наполнитель (очиститель и наполнятель), транспорт кегов, 3 контейнера CIP, шкаф управлени
Labelling machine for wrap-around belly labelling of 0.5 and 1.0 l PET bottles. The paper labels are glued to the bottle with hot glue., Additional title: wrap-around labelling, Capacity: 24000 b/h, Current: 18 A, Voltage: 400 V, Frequency: 50 Hz, Formats: PET bottles, 0,5 l, 1,0 l, 1,5 l, Running direction: left -> right, Operation / Control: Simatic S 7-300, Material: stainless steel housing, Position: free standing, Base construction: rectangular, enclosed machine, on spherical feet, Features: housing with viewing window, labelling module for wrap-around paper labels, Robatech hot melt melter , Periphery: Leibinger Jet 3, best-before date printer
PET bottle air conveyor over 2 floors, used for 0.5 l, 1.0 l and 1.5 l bottles. Length approx. 50 m. Our team at VBW Asset Trade will be happy to answer your questions. Send us an inquiry or simply give us a call!, Additional title: PET bottle conveyor system, Capacity: 24000 b/h, Formats: 0,5, 1,0 l und 1,5 l PET-bottles, Material: mainly stainless steel, Position: free-standing on the floor / suspended from the ceiling, Features: Bottle transport channel with bottle guides, with 2 x 360° and additional curves, with a 15° incline and horizontal run, 5 frequency-controlled blower motors
Конвейерные ленты для ящиков PETCYCLE, состоящие из моторизованных конвейерных лент и гравитационных роликов. Длина примерно 70 м, Дополнительное название: Маршруты транспортировки ящиков, Вместимость: 4000 ящиков/ч, Форматы: Петцикл-бокс для 20 x 0,5 л, 9 x 1,0 л, 6 x 1,0 л и 6 x 1,5 л ПЭТ-бутылок, Эксплуатация / Управление: панель управления / Siemens S7-300, Материал: преимущественно нержавеющая сталь, Положение: отдельно стоящая, Особенности: Петляные ленточные конвейеры, роликовые конвейеры, конвейерные рамы, П ...
Conveyor belts for PET bottles, with 1-lane hinged belt chain and 6 lanes. Capacity: 24,000 bottles/hour, Additional title: Free bottle conveyors, Capacity: 24000 b/h, Free bottle transport approx.: 30 m, 90° bottle transport curves: 1 piece 1-chain conveyor, 180° bottle transport curve: 1 piece 6-chain conveyor, Formats: PET-bottles in 0,5 l, 1,0 l, 1,5 l, Operation / Control: controlbox / Siemens S7-300, Material: mainly stainless steel, Position: free-standing, Features: Conveyor frames, deflection stations, drives, frequency controls, electrical switchgear, automatic belt lubrication
New bottle depalletiser on two levels. This new bottle skimming machine is a depalletiser with lifting frame in single-mast design. The mast is fitted with guide rails to support the vertically moving, roller-guided frame. The transfer device is attached to the lifting frame. The bottles are discharged in the upper area. The infeed and outfeed of the pallet transport is located under the transfer device. Our team at VBW Asset Trade will be happy to answer your questions. Send us an inquiry or simply give us a call!, Additional title: Depalletiser with lifting frame, Capacity: 140 layer/h, Power: 8,75 kW, Voltage: 230/400 Volt, Frequency: 50 Hz, Compressed air: 5,0 bar; 8,0 Nm³/h, Length: 4020 mm, Width: 3400 mm, Height: 5425 mm, Weight: 3800 kg, Formats: europalett (1200 x 800 x 140 mm), Operation / Control: control box / Siemens S7, Material: Painted mild steel, Position: free standing ...
Обзор Наполнитель под давлением был изготовлен в 2013 году немецким производителем KHS. Наполнитель под давлением всё ещё используется на крупной немецкой пивоварне и может быть осмотрен в любое время. Технические данные Вместимость: 22 000 - 65 000 b/h Количество заправочных станций: 168 Количество заправочных станций: 24 Заправка с кругом танга: 5040 мм Область подачи Узел клапана Вакуумный блок Гигиенический вход Инспекция уровня наполнения и закрывания Лента для отброса и отвержения Техническ ...
Обзор Стеклянный депаллетизатор был произведен немецкой компанией KHS в 2005 году и до недавнего времени входил в состав линии разлива в немецкой молочной компании. Паллетизатор сейчас выпускается, так как владелец останавливает производство. Технические детали/прицел Депаллетизатор с подъёмом и сбросом внизу С промежуточным средством для снятия слоя и магзином С затвором для верхнего слоя/крышки Закрытые конвейеры могут снимать по одной полосе для формированных бутылок, включая защи ...
- , , This PET single-use filling line is designed for bottle sizes of 0.5 L, 1.0 L, and 1.5 L and achieves a nominal output of up to 24,000 bottles per hour (for 1.0 L bottles). New bottles are destacked pallet by pallet on the new bottle unstacker and transported pneumatically to the rinser. The system consists of high-quality components from renowned manufacturers and includes: • - (KHS, 2001) • (KHS, 2001) • (Ortmann & Herbst, 1978) with downstream Velcorin dosing • - / , / (KHS, 2001) with chlorine dioxide and sterile water rinsing • -- (KHS, 2001) with Alcoa screw capper and liquid nitrogen dosing • (miho, 1992) • (KHS, 2001) • - (KHS, 2003) with hot melt glue applicator and best-before date printer This filling line is ideal for beverage manufacturers who want to fill water, soft drinks, or fruit spritzers in disposable PET bottle ...
Crate washer for PETCYCLE plastic crates, Additional title: Crate cleaning system, Capacity: 2950 crates/h, Power: 18 kW, Current: 38 A, Voltage: 230/400 V, Frequency: 50 Hz, Length: 7300 mm, Width: 1570 mm, Height: 1710 mm, Weight: 1900 kg, Formats: plastic crate: 20 x 0,5 l, 9 x 1,0 l, 6 x 1,0 l, 6 x 1,5 l , Running direction: transverse, Material: stainless steel, Position: free standing, Base construction: Self-supporting machine housing in block construction on spherical feet, Features: Caustic, hot water and fresh water spraying, inspection window, platform with staircase and railing, crate turner,
Packer for 0.5 litre, 1.0 litre and 1.5 litre PET bottles. Bottle holders: 5x20, 7x9 or 10x6 bottles., Additional title: Packing machine for bottle crates, Output according to design: 4000 crates/h, Current output approx.: 3000 crates/h , Air consumption: 0 Nm³/1000 bottles, Current: 17,59 A, Voltage: 220/400 V, Frequency: 50 Hz, Compressed air: 4 - 5 bar, Length: 3680 mm, Width: 2940 mm, Height: 2610 mm, Weight: 4200 kg, Formats: 0,5 l, 1,0 l und 1,5 l PET-bottles, Running direction: left -> right, Operation / Control: converted to manual / PLC defective, Material: stainless steel / painted black steel, Position: free standing, Base construction: rectangular cycle packer machine on four columns with spherical feet, Features: Plexiglas safety screen opening upwards, safety grid, infeed and outfeed conveyors, packing head equipment for 0.5 l, 1.0 l and 1.5 l bottles, control panel conver ...
Combined rinser and filler for 0.5 litre, 1.0 litre and 1.5 litre PET bottles. Output: 24,000 bottles/h A chlorine dioxide dosing unit and a sterile water supply are connected to the rinser. The filler is equipped with a screw capper. The filling quantity is controlled via flow measurement. Liquid nitrogen dosing is possible via a mobile system., Additional title: PET bottle sanitising and filling system, Capacity: 24000 b/h , Formats: 0,5 l, 1,0 l und 1,5 l PET-bottles, Running direction: left -> right, Operation / Control: Touch-Panel / Simatic S 7, Material: mainly stainless steel, Position: free standing, Features: Stainless steel enclosure, plexiglass protective screen opening upwards; 70 rinsing valves on the rinser; 80 filling valves; filling quantity recording via IDM; Alcoa capper 28 mm Bericap; Prominent chlorine dioxide dosing; filtration system for sterile water, mobile liqui ...
Производитель: KHS Модель: Innoket Roland 10/4 Год производства: 2009 Тип бутылки: квадратные бутылки Выпуск: до 20 000 бутылок в час Доступные форматы лейблов - Этикетки для влажного клея (форматы VE и RE) - Самоклеящиеся этикетки Размеры форматов - 250 мл - 33 x 119 мм - 500 мл - 36 x 150 мм - 750 мл - 48 x 158 мм Запасные части - Доступно множество запасных частей, включая штампы, клеевой валик, скребки и роликовые губки. Подробнее можно найти здесь - / Свяжитесь с нами по адресу -
Обзор Паллетизатор был произведён немецкой компанией KHS в 2005 году и до недавнего времени входил в состав линии разлива в немецкой молочной компании. Паллетизатор сейчас выпускается, так как владелец сокращает производство. Технические детали/объём Работали с лотком/коробками по 8 единиц (4x2). Погрузчик паллетов с головкой затвора, включая защитные ограждения, транспортировку поддонов, транспортировку лотков, переворотчик лотков, формировочный стол, магазин для пустых паллето
Технические характеристики и данные о производительности KHS Innofill-ER VF 143/20 — это высокоскоростной изобарический моноблок для наполнения, предназначенный для премиальных стеклянных бутылок в производстве напитков. Разработанный для надёжности в промышленных упаковочных условиях, он обеспечивает стабильную производительность для безалкогольных напитков, газированной воды и неподвижной воды на подержанных линиях разлива. Производитель: KHS Модель: Innofill-ER VF 143/20 Категория: Моноблок напо ...
Подержанная наполнка KHS Innofill может 16000 CPH — 2018 год. Технические характеристики и данные о производительности. Эта полная подержанная линия для розлива — это система консервирования подержанных напитков, спроектированная на базе блока KHS, интегрировавшаяся с высококачественным оборудованием для упаковки на переднем и следующем этапе. Разработанный для промышленной упаковки и производства напитков, он обеспечивает надёжную работу для алюминиевых банок. Скорость производства: до 16000 cph ...
General SKU366W1294 MakeKHS TypeEFA 60.125CW12 No.963182 Mach.No.963182 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Working pressure jacket6 Bar Vacuum possible jacketcheck Number of horizontal pressure tanks1 Main Features MaterialStainless steel Volume150 Ltr. Pressure6 Bar Surface0.28 m2 Specified Features - Nutsche filter Nutsche filtercheck Filter surface0,28m² Capacity150l Vessel sizesDia. 600x600 mm Plate sizesDia. 600MM Top connectionsDN25 Liquid outletDN25 Max. temperature-25°C/+200°C With jacketcheck Nutsche filters Capacity150 l. Specified Features - Nutsche filter MaterialStainless steel 1.4435 (316L), Stainless steel 1.4571 (316Ti) General Mounted on legscheck LocationBarneveld Floorspace1,20x1,15 m Total height1,90 m Weight860 KG Extra Specificationsthe bottom can be opened hydraulically by hand pump ...
Производительность: 15000 У/ч // Размер бутылки: 1500 м
