table length: 1500 mmtable width: 1000 mmtable height: 150 mmbore: 22 mmweight: 420 kgEquipment:- 4 feet - basic equipment 650 mm- high-quality steel S355J2+N + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Hole Ø 28 mm- Drill holes surface 100x100 mm grid- Corners, edges and drill holes rounded- Side panel height 200 mm- Hole spacing side panel 50 mm- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise superstructuresThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1500 mmtable width: 1500 mmtable height: 150 mmbore: 22 mmweight: 585 kgEquipment:- 4 feet - basic equipment 650 mm- high-quality steel S355J2+N + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Hole Ø 28 mm- Drill holes surface 100x100 mm grid- Corners, edges and drill holes rounded- Side panel height 200 mm- Hole spacing side panel 50 mm- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise superstructuresThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2000 mmtable width: 1000 mmtable height: 200 mmbore: 28 mmweight: 730 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1200 mmtable width: 800 mmtable height: 200 mmbore: 28 mmweight: 408 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1200 mmtable width: 1200 mmtable height: 200 mmbore: 28 mmweight: 544 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2000 mmtable width: 2000 mmtable height: 200 mmbore: 28 mmweight: 1299 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mmtable width: 1500 mmtable height: 150 mmbore: 22 mmweight: 1100 kgEquipment:- 4 feet - basic equipment 650 mm- high-quality steel S355J2+N + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Hole Ø 28 mm- Drill holes surface 100x100 mm grid- Corners, edges and drill holes rounded- Side panel height 200 mm- Hole spacing side panel 50 mm- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise superstructuresThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2000 mmtable width: 1000 mmtable height: 150 mmbore: 22 mmweight: 530 kgEquipment:- 4 feet - basic equipment 650 mm- high-quality steel S355J2+N + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Hole Ø 28 mm- Drill holes surface 100x100 mm grid- Corners, edges and drill holes rounded- Side panel height 200 mm- Hole spacing side panel 50 mm- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise superstructuresThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1200 mmtable width: 1200 mmtable height: 200 mmbore: 28 mmweight: 521 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1500 mmtable width: 1000 mmtable height: 200 mmbore: 28 mmweight: 554 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number: 124 bore: 28 mmweight: 326 kg4-283500consisting of:- 14x Professional screw clamp - nitrided -- 10x Professional screw clamp 45°/90° - nitrided- 8x Prism Ø 50 135° with screwed-in collar - nitrided- 36x Quick-clamping bolts without groove, double - burnished- 8x magnetic clamping bolts 68 - aluminum- 12x universal stop 150 L - nitrided- 12x universal stop 225 L - nitrided- 4x universal stop 500 S - nitrided- 12x stop and clamping bracket 175 L - nitrided- 2x stop and clamping bracket 300 G - nitrided- 2x stop and clamping bracket 500 G - nitrided- 1x stop and clamping bracket 500 G with rotation angle left - nitrided & stop and clamping bracket and clamping bracket 500 G with rotation angle right - nitrided- 1x stop and clamping bracket 750 G left - nitrided & stop and clamping bracketClamping bracket 750 G right - nitrided- 1x stop and clamping bracket 800 GK left - nitrided ...
table length: 3000 mmtable width: 1500 mmtable height: 150 mmbore: 22 mmweight: 1075 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number: 32 bore: 28 mmweight: 51,2 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mmtable width: 1500 mmtable height: 200 mmbore: 28 mmweight: 1425 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore: 22 mmweight: 214 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2000 mmtable width: 1000 mmtable height: 200 mmbore: 28 mm: 100 x 100 mmmaterial thickness: ca. 24,5 - 27 mmSide panel height: 200 mmwork height max.: 850 mmweight: 850 kgProduct description:Siegmund retro offer incl. accessories:>- high-quality steel S355J2+N + plasma nitriding- Side panel holes in diagonal grid- Corners, edges and drill holes chamfered 45°- Construction reinforced with ribs- incl. basic foot equipment (working height 850 mm)Accessories:- 6 x Professional screw clamp, nitrided- 12 x quick-release bolts without groove, double burnished- 8 x universal fence 225 L nitrided- 2 x stop and clamping bracket 175 L nitrided- 2 x stop and clamping angle 500 G nitrided- 1 x accessory set - Eccentric stop Ø 60 with M10 thread nitrided - Hexagon socket wrench size 6 - Brush Ø 30 with protective cap - CleanBasic 1 liter in spray bottle - Anti-stick 1 l ...
table length: 1200 mmtable width: 800 mmtable height: 200 mmbore: 28 mmweight: 392 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mmtable width: 1500 mmtable height: 200 mmbore: 28 mmmaterial thickness: ca. 24,5 - 27 mm: 200 mmweight: ca. 1.553 kgProduct description:Siegmund Retro Offer: Welding table as it was 25 years ago, additionally with plasma nitriding and current table feet.Welding table:- High-quality steel S355J2+N + plasma nitriding 200- Holes surface 100x100 mm grid- Corners, edges, and holes 45° chamfered- Holes side panel in diagonal grid- Construction reinforced by ribs- Includes basic foot equipment (working height 850 mm)Accessories:- 6 x professional nitrided screw clamps- 12 x quick-release bolts without groove, double burnished- 8 x universal stop 225 L nitrided- 2 x stop and clamping angle 175 L nitrided- 2 x stop and clamping angle 500 G nitrided- 1 x accessory set - Eccentric stop Ø 60 with M10 thread, nitrided- Allen key size 6- Brush Ø 30 with protective cap- CleanB ...
table length: 1200 mmtable width: 1200 mmtable height: 150 mmbore: 22 mmweight: 395 kgEquipment:- 4 feet - basic equipment 650 mm- high-quality steel S355J2+N + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Hole Ø 28 mm- Drill holes surface 100x100 mm grid- Corners, edges and drill holes rounded- Side panel height 200 mm- Hole spacing side panel 50 mm- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise superstructuresThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
フロアプレートの長さ: 1500 mmフロアプレートの幅: 1260 mmフロアプレートの高さ: 400 mmこの広告のデータは、LogoTech oHGのソフトウェアソリューションであるModulMWSで作 されました
table length: 2990 mmtable width: 1490 mmtable height: 850 - 900 mmweight of the machine ca.: 0,8 tWelding table / perforated table:with milled and deburred holesHole diameter: 28 mmThe table is made of 15 mm thick, high-alloy steel S355 JR T=15The surface is untreated.Side panels 165 mmHeight adjustable from approx. 880 - 980 mmRibbed underside for reinforcement.Including floor bearingsAccessories optional!Surface flatness 0.2 - 0.5 mm over 1000 mm.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2400 mmtable width: 1200 mmtable height: 850 - 900 mmweight of the machine ca.: 0,65 tWelding table / perforated table:with milled and deburred holesHole diameter: 28 mmThe table is made of 15 mm thick, high-alloy steel S355 JR T=15The surface is untreated.Side panels 165 mmHeight adjustable from approx. 880 - 980 mmRibbed underside for reinforcement.Including floor bearingsAccessories optional!Surface flatness 0.2 - 0.4 mm over 1000 mm.The table can be moved with a pallet truck.Pallet truck is not included.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1000 mmtable width: 1000 mmtable height: 200 mmbore: 28 mmweight: 416 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2400 mmtable width: 1200 mmtable height: mm: 4000 kgheight of stroke: 510 - 1550 mmtotal connected load: 1,5 kWconnected load frequency: 400 Vweight of the machine ca.: 0.95 tWelding table on lifting table:Hole diameter: 28mmThe table is made of 15mm thick S355 steelThe surface is stained and oiled.Tolerance: +/- 1 mm at the top and +/- 1 degree at the sides.Side panels 150 x 10mmRibbed bottom for reinforcement.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2400 mmtable width: 1200 mmtable height: 200 mmbore: 28 mm: 100 x 100 mmmaterial thickness: ca. 24,5 - 27 mm: 200 mmwork height max.: 850 mmProduct description:Siegmund retro offer incl. accessories:>.- high-quality steel S355J2+N + plasma nitriding- Drill holes in side panel in diagonal grid- Corners, edges and drill holes bevelled 45- Construction reinforced by ribs- incl. base basic equipment 650 mmAccessories:- 6 x Professional screw clamp, nitrided- 2 x stop and clamping angle 175 L nitrided- 10 x quick-clamping bolts without groove, double burnished- 8 x universal stop 225 L nitrided- 2 x stop and clamping bracket 500 G nitrided- 1 x accessory setThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mmtable width: 1500 mmtable height: 200 mmweight of the machine ca.: 1,6 tThe Professional 750 4-280040.PD 3000x1500x200 mm table has a diagonal hole arrangement on the table top and a parallel hole arrangement in the 50 mm grid on the sides.The holes have a diameter of 28 mm. The table has a material thickness of about 24.5-27 mm and is made of high quality steel S355J2 + N.Grid lines at intervals of 100 mm make it easier for you to set up your device.The welding tables are provided with scale as standard.Including 6x feet basic equipment 650 Article no. 280858.XThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 0,6 t: -- mm: -- mmconsisting of:30x article no. 2-280510Quick release pin short- Clamping of 2 components- burnished- with twist lock8x article no. 2-280410.NUniversal stop 150 L - nitrided- nitrided- as standard with fine scaling on both sides4x article no. 2-280420.NUniversal stop 225 L - nitrided- nitrided- as standard with fine scaling on both sides8x article no. 2-280110.GStop and clamping angle 175 L - cast / black oxide finish- Hole / elongated hole- Cast / burnished2x article no. 2-280162.NStop and clamping angle 500 G - nitrided- Left stop- nitrided1x article no. 2-280166.NStop and clamping angle 750 G left - nitrided- Left stop- nitrided 1x article no. 2-280167.NStop and clamping angle 750 G right - nitrided- stop on the right- nitrided1x article no. 2-280910Tool trolley- painted- Permissible total weight 240 kg1x article no. 2-280164.NStop and clamping angle 500 G with turn ...
table length: 2400 mmtable width: 1200 mmtable height: 200 mmweight of the machine ca.: 1,0 tThe table Professional Extreme Article no. 4-280030.X7 2400x1200x200 mm has a hole arrangement in the 100 mm grid on the table top and a parallel hole arrangement in the 50 mm grid on the sides.The holes have a diameter of 28 mm and the table has a material thickness of about 24.5-27 mm. The table top is made of hardened tool steel.The low-loaded sidewalls are still made of steel S355J2 + N for cost reasons. Grid lines at a distance of 100 mm make it easier for you to set up your device.The welding tables are provided with scale as standard.Including 4x feet Basic equipment 650 Article no. 280858.XThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mmtable width: 1500 mmtable height: 200 mmweight of the machine ca.: 1,6 tThe table Professional Extreme Article no. 4-280040.X7 2400x1200x200 mm has a hole arrangement in the 100 mm grid on the table top and a parallel hole arrangement in the 50 mm grid on the sides.The holes have a diameter of 28 mm and the table has a material thickness of about 24.5-27 mm. The table top is made of hardened tool steel.The low-loaded sidewalls are still made of steel S355J2 + N for cost reasons. Grid lines at intervals of 100 mm make it easier for you to set up your device.The welding tables are provided with scale as standard.Including 6x feet basic equipment 650 Article no. 280858.XThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 690 mmtable load: 500 kgswivelling range: 0 - 90 Gradtable load: horizontal 500 Kgtable load: vertikal 250 Kgboring diameter: 100 mmtable turning speeds: 0,2 - 1,9 U/mintotal power requirement: 0,37 kWThe D-BYT N welding manipulator has a hollow shaft, also known asSpindle bore in the rotary table, which makes inert gas welding possible. theDue to the compact design, turn-tilt tables can be installed in anyintegrate existing production facilities. Inert gas welding (forming gas).thereby simplified.Features:- Double foot pedal (start-stop/left-right) included- The new welding table D-BYT-500N includes, in addition to the standard start/Stop foot pedal also an extra remote control (on the cable).- Infinitely adjustable rotation speed of the table- Suitable for any welding process, even high frequency- Very high stability - compact model- Through hole in the turntable plate- ...
table length: 2400 mmtable width: 1200 mmtable height: 200 mmweight of the machine ca.: 913 kg280030.XD7D- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 24.5 – 27 mm- Sidewall made of high quality steel S355J2+N + plasma nitriding- Bore Ø 28 mm- Holes surface in diagonal grid- Rounded corners, edges and holes- Side panel height 200 mm- Holes in the side wall in the diagonal grid- Including scaling on the surface- Structure reinforced with ribs- Grid lines enable precise build-upsIncluding 4x feet basic equipment 650 item no. 280858.XThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2400 mmtable width: 1200 mmtable height: 850 - 900 mmweight of the machine ca.: 0,65 tdimensions: 2,4 x 1,2 x 0,95 mWelding table / perforated table:Hole diameter: 28mmThe table is made of 15mm thick, high-alloy steel S355 JR T=15The surface is untreated.Side panels 165mmBottom ribbed for reinforcement.Incl. floor bearingAccessories optionalSurface evenness 0.2 - 0.4mm over 1000mm.- with drawer unit- Grid shelf- Heavy-duty castors steerableWelding accessories shown not included!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number: 10 Stk.clamping range: 15 - 50 mm: 28 mmweight: 10 kgdimensions: 0,3 x 0,3 x 0,2 mBasic set 4 / 53 piecesfor table top thickness 15mm and 25mm6 pcs screw clamps14 pcs. quick clamping bolts2 pcs. universal stop 100mm6 pcs. universal stop 150mm6 pcs. universal stop 225mm2 pcs. universal stop 300mm6 stop and clamping angles 175mm4 stop and clamping angles 275mm2 pcs. prisms 60mm1 piece torch holder1 pc. Eccentric stop 100mm diameter1 piece perforated brush 30mm2 pieces separating lotion 500ml, on a natural, biological basis2 pcs. Welding table cleaner 500ml, on a natural, biological basisThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number: 53 Positionenweight: 45 kgcondition: neu 0Basic set 4 / 53 piecesfor table top thickness 15mm and 25mm6 pcs screw clamps14 pcs. quick clamping bolts2 pcs. universal stop 100mm6 pcs. universal stop 150mm6 pcs. universal stop 225mm2 pcs. universal stop 300mm6 stop and clamping angles 175mm4 stop and clamping angles 275mm2 pcs. prisms 60mm1 piece torch holder1 pc. Eccentric stop 100mm diameter1 piece perforated brush 30mm2 pieces separating lotion 500ml, on a natural, biological basis2 pcs. Welding table cleaner 500ml, on a natural, biological basisThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
数:24ポジショネン重量:22kg状態:neu 0基本セット1/24個テーブルトップ厚15・25mm用4個クラ プ、クランプ高さ300mm、可変投影8本クランプボル 2個ストップ100mm4個 ストップ150mm2個ストップ225mm1個トーチホルダー1個 穴あきブラシ30mm1個 セパレーティングローション500ml1個自然、生物学的 基盤の溶接テーブルクリーナー500ml
table length: 2000 mmtable width: 1000 mmtable height: 920 - 1000 mmweight of the machine ca.: 0,45 tWelding table / hole table:Hole diameter: 28mmThe table is made of 15mm thick S355 steelThe surface is stained and oiled.Tolerance: +/- 1 mm at the top and +/- 1 degree at the sides.Side panels 150 x 10mmHeight adjustable from approx. 920 - 1000mmRibbed bottom for reinforcement.including floor storageAccessories optionalAccessories shown are optionalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2400 mmtable width: 1200 mmtable height: 200 mmweight of the machine ca.: 1,0 tThe table Professional 750 Article no. 4-280030.PD 2400x1200x200 mm has a diagonal hole arrangement on the table top and a parallel hole arrangement in 50 mm grid on the sides.The holes have a diameter of 28 mm. The table has a material thickness of about 24.5-27 mm and is made of high quality steel S355J2 + N.Grid lines at a distance of 100 mm make it easier for you to set up your device.The welding tables are provided with scale as standard.Including 4x feet Basic equipment 650 Article no. 280858.XThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1200 mmtable width: 800 mmtable height: 840 - 890 mmweight of the machine ca.: 0,3 tWelding table / perforated table:Hole diameter: 28mmThe table is made of 15mm thick, high-alloy steel S355 JR T = 15The surface is untreated.Sidewalls 165mmheight adjustable from approx. 880 - 980mmRibbed underside for reinforcement.including floor storageAccessories optional Surface flatness 0.2 - 0.4mm on 1000mm.The table can be moved with a pallet truck.Pallet truck is not included in the scope of delivery The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1300 mmtable width: 800 mmtable height: 920 - 1000 mm: 1000 kgheight of stroke: 510 - 1550 mmtotal connected load: 1,5 kWconnected load frequency: 230 Vweight of the machine ca.: 0,55 tWelding table on lifting table:Hole diameter: 28mmThe table is made of 15mm thick S355 steelThe surface is stained and oiled.Tolerance: +/- 1 mm at the top and +/- 1 degree at the sides.Side panels 150 x 10mmRibbed bottom for reinforcement.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2990 mmtable width: 1490 mmtable height: 850 - 900 mmweight of the machine ca.: 0,8 tWelding table / perforated table:Hole diameter: 28mmThe table is made of 15mm thick, high-alloy steel S355 JR T = 15The surface is untreated.Sidewalls 165mmheight adjustable from approx. 880 - 980mmRibbed underside for reinforcement.including floor storageAccessories optional Surface flatness 0.2 - 0.4mm on 1000mm.The table can be moved with a pallet truck.Pallet truck is not included in the scope of delivery The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2400 mmtable width: 1200 mmtable height: 850 - 900 mmweight of the machine ca.: 0,65 tWelding table / perforated table:Hole diameter: 28mmThe table is made of 15mm thick, high-alloy steel S355 JR T = 15The surface is untreated.Sidewalls 165mmheight adjustable from approx. 880 - 980mmRibbed underside for reinforcement.including floor storageAccessories optional Surface flatness 0.2 - 0.4mm on 1000mm.The table can be moved with a pallet truck.Pallet truck is not included in the scope of delivery The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number: 43 Positionenweight: 40 kgcondition: neu 0Basic set 3 / 43 piecesfor table top thickness 15mm and 25mm6 pcs screw clamps12 pcs. quick clamping bolts6 pcs. universal stop 150mm6 pcs. universal stop 225mm2 stop and clamping angles 175mm2 stop and clamping angles 275mm2 pcs. prisms 60mm1 piece torch holder1 pc. Eccentric stop 100mm diameter1 piece perforated brush 30mm2 pieces separating lotion 500ml, on a natural, biological basis2 pcs. Welding table cleaner 500ml, on a natural, biological basisThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: ? mmtable width: ? mmtable height: ? mmtotal power requirement: 1,2 kWweight of the machine ca.: 0,75 tdimensions of the machine ca.: 3,51,61,5 mSet of welding stations (6 pieces) + suction unitShipping - Dimensions:6 welding tables 3 Euro palletsExtraction unit approx. 1.6 x 0.8 x 1.5 m on Euro palletTotal weight estimated approx. 750 kg.6 welding stations / tables + suction unitDrive: 1.2Extraction with 1.78 m³ / sThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
テーブルの長さ:4000 mmテーブル幅:2000 mm:28 mmテーブルの高さ:815 mm:kg機械の重量 ca.:1,3 t溶接テーブル/穴あきテーブル:穴径:28mmテーブルは さ15mmの高合金鋼S355 JR T = 15表面は未処理です補強のためのリブ付き下
floor-plate length: 3000 mmfloor-plate width: 1500 mmfloor-plate height: 150 mmtotal power requirement: kWweight of the machine ca.: 750 Kgdimensions of the machine ca.: 3,0 x 1,5 x 1,3 mThe welding table is made of 15 mm thick steel plates.assembled and welded.The table stands on height-adjustable feet.The mounting holes for the assembly and fastening parts have a diameter of 28 mm.A starter package with alignment and fastening parts is included at a price of € 750,00 (price is included)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 2000 mmtable width: 1000 mmtable height: 920 - 1000 mm: 2000 kgheight of stroke: max. 1525 mmtotal connected load: 1,5 kWconnected load frequency: 400 Vweight of the machine ca.: tWelding table on lifting table:Hole diameter: 28mmThe table is made of 15mm thick S355 steelThe surface is stained and oiled.Tolerance: +/- 1 mm at the top and +/- 1 degree at the sides.Side panels 150 x 10mmRibbed bottom for reinforcement.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1200 mmtable width: 1200 mmtable height: 840 - 890 mmweight of the machine ca.: 0,32 tWelding table / perforated table:Hole diameter: 28mmThe table is made of 15mm thick, high-alloy steel S355 JR T = 15The surface is untreated.Sidewalls 165mmheight adjustable from approx. 880 - 980mmRibbed underside for reinforcement.including floor storageAccessories optional Surface flatness 0.2 - 0.4mm on 1000mm.The table can be moved with a pallet truck.Pallet truck is not included in the scope of delivery The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
number: 10 Stk.clamping range: 15 - 50 mm: 28 mmweight: 10 kgdimensions: 0,3 x 0,3 x 0,2 mBasic set 4 / 53 piecesfor table top thickness 15mm and 25mm6 pcs screw clamps14 pcs. quick clamping bolts2 pcs. universal stop 100mm6 pcs. universal stop 150mm6 pcs. universal stop 225mm2 pcs. universal stop 300mm6 stop and clamping angles 175mm4 stop and clamping angles 275mm2 pcs. prisms 60mm1 piece torch holder1 pc. Eccentric stop 100mm diameter1 piece perforated brush 30mm2 pieces separating lotion 500ml, on a natural, biological basis2 pcs. Welding table cleaner 500ml, on a natural, biological basisThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
テーブルの長さ:1150ミリメートルテーブル幅:1150ミリ メートルテーブル負荷:2トン総電力要件:機械のkW重 約:t機械の寸法約:mブランド:JWeldingタイプ:HB-20容量:2 .000キロプラトー寸法:1.150ミリメートルø作業高さプ ットフォーム、水平:1.180ミリメートル作業高さプ ットフォーム、垂直:1.000ミリメートル回転直径垂直 :1.550ミリメートルøTスロット: 8 電気的に傾け可
テーブルの長さ:1200ミリメートルテーブル幅:800ミリ ートル:28ミリメートルテーブルの高さ:450 - 800ミリメートル:500キロマシンの重量ca.:0,8 t溶接テーブル/穴あきテーブル:穴径:28ミリメートル ーブルは厚さ15mm、高合金鋼S355 JR T = 15でできており、表面は未処理です。補強のために 面をリブ付き
