We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Fabricant:
(Catégorie: 709)
utilisé
Équipement : Agitateur, État : Neuf en usine, Documents techniques : Dessin, Agitateur : Hélice, Disposition de l’agitateur : excentrique dans la couche arable, Vitesse : 1 430, Paliers inférieurs : Non, Voltvolt : 400, Puissance : 2,2,Interféreur de courant : Non, Matériau en contact avec le produit : V4A 1.4571 (AISI316), Plaque de type : Oui, Longueur de l’arbre : 1460, Diamètre de l’arbre : 42, Diamètre de la pale : 200
utilisé
Équipement : Agitateur, État : utilisé, Agitateur fabricant : TMR, Agitateur : Hélice, Vitesse : 1,430, Palier inférieur : Non, Tension Volt : 400/690, Puissance : 4, Interféreur de courant : Non, Matériau en contact avec le produit : V4A 1.4571 (AISI316), Plaque de type : Oui, Équipement de l’agitateur : Dessin principal disponible (légères déviations dimensionnelles présentes) Les agitateurs n’ont été utilisés que pendant une courte période selon l’opérateur précédent, un agitateur avec une petite bosse dans le couvercle du ventilateur du moteur (voir photos), Longueur de l’arbre : 740, diamètre de l’arbre : 50, diamètre de l’aile : 220
utilisé
Équipement : Agitateur, État : utilisé, Autres : Agitateur incomplet, rotor (hélice) de diamètre manquant, haut du stator environ 350 mm, diamètre inférieur du stator environ 300 mm, Agitateur fabricant : Ystral, Agitateur : mélangeur à jet, Vitesse : 730 / 1475, Palier inférieur : Non, Voltvoltvolt : 380, Puissance : 3,5 / 13, Interféreur de courant : Non, Matériau en contact avec le produit : V2A 1.4301 (AISI304), Plaque nominative : Oui, Longueur d’onde : 600, Diamètre de l’arbre : 75
utilisé
Équipement : Agitateur, État : neuf en usine, Agitateur : agitateur : Agitateur : Vitesse : 17, Palier inférieur : Non, Voltvolt : 230/400, Puissance : 3, Interféreur de courant : Non, Matériau en contact avec le produit : V4A 1.4401/04 (AISI316), Plaque de type : Oui, Équipement de l’agitateur : Longueur d’onde mesurée sous la lanterne Diamètre des pales d’agitation : environ 1 x 1 130 mm, 1 x 1 530 mm, 1 x 1 930 mm Les lames de l’agitateur doivent être soudées à l’arbre de l’agitateur sur place avant l’utilisation de l’agitateur, un agitateur manque de la lanterne, Longueur d’onde : 2620, Diamètre de l’arbre : 60
utilisé
Équipement : Agitateur, État : utilisé, Autres : Également vendu avec un réservoir de mélange assorti, voir #8336. Agitateur fabricant : Ystral, Agitateur : Mélangeur à jet, Vitesse : 730 / 1455, Paliers inférieurs : Non, Voltvolt : 400, Puissance : 13 / 19, Interféreur de courant : Non, Matériau en contact avec le produit : V2A 1.4301 (AISI304), Plaque de type : Oui
utilisé
État : utilisé, Autres : Puissance de transmission : 11 kW Domaines d’application : Mélange / homogénéisation et pompage sur émulsions et pâtes, Hauteur totale : 650, Longueur totale : 1 200, Largeur totale : 460
utilisé
État : utilisé, Autres : Largeur totale : 1 950 mm Profondeur totale : 1 050 mm Hauteur totale : 1 400 mm Mélangeur chaud : environ 10 litres - 5,5 kWC Mélangeur de modification : environ 25 litres - 2,2 kWFa fermeture de bride du mélangeur chaud peut manquer et devra être remplacée sur place, Fabricant : DIOSNA Dierks & Söhne
utilisé
utilisé
The Mapro Positive Displacement Blower consist basically of a pair of Tri-lobe rotors, mounted on parallel shafts, rotating in opposite directions inside a properly shaped casing closed at the ends by side plates. The two Tri-lobe rotors are synchronized by a pair of timing gears. As the rotors rotate, air is drawn into the inlet side of the casing, is moved from the inlet to the outlet side by the free volumes, between rotors and stator and finally is forced out of the outlet side against the connected system pressure. The blower does not develop pressure within the casing but the discharge pressure depends only upon the connected system resistance. Motor: 22 kW - 400 V - 50 Hz - 2.950 rpm - 38,8 A. P(inlet): 1.013 hPa. P(outlet): 800 hPa. PS: 820 hPa. T amb: 20/40 °C. Blower speed: 2.500 rpm. Q: 372 cfm. Sound level: 89 dB(A)., Type of Machine: Positive displacement blower, Stock Numb ...
utilisé
Données techniques : Machine à fileter : Fabricant : PRIMA s.r.l Modèle n° : WCLSE-1000/1 Numéro de série 2180553-01 Capacité 200-800 kg/h Escargot grimpant : Machine : Convoyeur Fabricant : PRIMA s.r.l Type : Convoyeur cochléaire Modèle n° : CHT50B003 Numéro de série : 2180553-03 Schnetzler : Machine : Dispositif de coupe Fabricant : PRIMA s.r.l Modèle n° : CHT50B003 Numéro de série : 2180533-02 Dispositif de levage et d’inclinaison : Fabricant : Frontmatec Hygiene GmbH Type 27000 Pour accueillir des chariots de chargement standard de 200 et 300 litres pour le Utilisation rationnelle dans l’industrie alimentaire Année de construction : 2019
utilisé
Incomplete Cream separator (Skimmer). Self cleaning. Machine comes with the frame, bowl, hood, horizontal and vertical axle., Additional features:, Excludin g:, - Motor., - Motorcover., - Baseplate and feet, - Waterbox with water valves., - Inlet / outlet pipes., - Control panel., - Service tools for maintenance., Additional with this stocknumber several unused and used spare parts., Type of Machine: Cream Separator / Skimmer, Capacity: 12.000 liter per hour, Bowl speed: 4.450 rpm, Weight: 1.420 kg, Dimensions: 145 x 110 x 175 cm
utilisé
Automatic foil wrapping machine which can be used for packing products like margarine or butter into aluminium foil. The machine is in a good as condition with main control panel with Siemens S7-200 PLC and frequency converter and operation panel with Siemens TD200 Operator Interface. Previously used in a margarine factory. The machine is equiped with a rotating forming drum with 4x rectangular molding chambers. The format on the machine is 250 gram, 98 x 65 x ± 41 mm. SIG folding principle (folding flap on the side, for less foil usage). The margarine is feed with a direct connection with compensator and return line. The machine is equiped with a photocell on the paper infeed, to control the exact position of the print on the foil. The speed can be adjusted by a frequency converter between 30 - 120 packages per minute (depending on product, packaging material and surrounding conditions ...
utilisé
IMA P10K Automatic Butter Roll – Round – Log – portion wrapping machine in aluminium foil / parchment paper., The machine is included with the following pack format sets:, - Logs (or) Rolls (or) Round (or) Cylinder – ± 43 mm x 110 mm = 125 gram (complete), - Logs (or) Rolls (or) Round (or) Cylinder – ± 48 mm x 160 mm = 250 gram (complete including extra mouldset of ± 45 mm to reach ± 230 gram)., - Rectangular Blocks (or) Portions – 100 mm x 75 mm x 35 mm = 250 gram (filling nozzle and 1x guide for the bricks when they are upside down are missing)., - Rectangular Blocks (or) Portions – 160 mm x 105 mm x 65 mm = 1.000 gram (Guiding plate upside down, side guides and support level missing)., Product is fed through the hopper which includes a butter screw feeder., Maximum Speed: up to 60 packs per minute (Varies depending on the portion size), Products that can be packed ...
utilisé
Inspecteur de bouteilles vides HEUFT d’occasion 72000 BPHToches techniques et données de performance Cet inspecteur de bouteilles vides (EBI) est conçu pour la production rapide de boissons et les environnements d’emballage industriel. Fabriqué par HEUFT, le système combine un inspecteur HEUFT InLine reflexx Release 9 avec une unité de présélection HEUFT Spectrum SX TB 72, connectée en réseau pour un contrôle complet du débit en bouteille. Conçu pour être intégré dans une gamme d’embouteillage d’occasion, il offre des performances d’inspection robustes pour les bouteilles en verre retournables à des vitesses allant jusqu’à 72 000 bouteilles par heure. Fabricant : HEUFT Modèle de composition : InLine
utilisé
Complete powder plant existing out of Evaporator (4-effect, TVR), Spray Dryer, Fluidbed Dryer, 2x Crystallization Tanks and a Big Bag Filling Station. Previously used for skim milk / whole milk / whey / permeate or 35% protein powder. Still mounted on its original postion inside the factory in Spain. Line per direct available., Infeed capacities evaporator:, - Skim milk: 7.200 kg/h @ 9% TS., - Whole milk: 4.800 kg/h @ 12,5% TS., - Whey: 8.150 kg/h @ 6% TS., - Permeate: 8.835 kg/h @ 4,5% TS., - 35% Protein: 2.880 kg/h @ 10% TS., - Water for startup and CIP: 10.000 ltr/h @ 2 bar., - Water for cooling seals in vacuum pumps: 7.000 ltr/h @ 25 °C - 2 bar, demineralized., - Water for safety / firefighting should be available at 7.000 ltr/h @ 2 bar., - Water for condenser cooling: 30.000 ltr/h @ 28 °C - 2 bar., - Ice water for flash system: 2.000 ltr/h @ 3 °C - 2 bar., - Saturated dry steam: ...
utilisé
APV pilot UHT plant equipped with an indirect heating module using a plate heat exchanger and an aseptic homogeniser. The unit was previously used for R&D purposes in a dairy plant in Belgium. Capacity up to 400 litres per hour. Temperature profile: approx. 4 – 145 – 20 °C., The skid-mounted unit consists of a plate heat exchanger (APV T4) with 5 sections and a total of 127 plates (9-15-23-55-25), two regeneration sections, heating and cooling sections, hot water/steam section and indirect steam heating. The system is further equipped with three connectable holding tubes, balance tank (Ø 38 cm, height 75 cm, volume approx. 80 litres) with agitator for ingredient mixing, water circulation pump, centrifugal product pump feeding the balance tank and a high-pressure plunger pump (Cat) with variable speed control via frequency inverter. The installation includes all required valves and ...
utilisé
Cream separator (Skimmer). Self cleaning. Machine comes with the bowl, motor (15 kW), motor cover, base plate with feet, cyclone and all inlet / outlet pipes., Additional features:, Excluding:, - Waterbox with water valves., - Control panel., - Service tools for maintenance., Type of Machine: Cream Separator / Skimmer, Capacity: 15.000 liter per hour, Bowl speed: 5.000 rpm, Motor: 22 kW - 380 V - 42 A - 1.450 rpm - 50 Hz - 3 Ph, Weight: ± 1.650 kg, Dimensions: 145 x 110 x 175 cm
utilisé
État : utilisé, Fabricant : Gram Equipment, Remarques : Usine très efficace pour la production de glaces / glaces avec une capacité de 7 200 pièces jusqu’à 42 000 pièces par heure. La taille actuelle du moule installé est de 35 ml de produits à glace. Fabriqué en 2008. La gamme complète est à vendre, incluant le contrôle, l’inséreur automatique de sticks, le wrapper et d’autres composants. La documentation complète est disponible. Le système a été utilisé jusqu’en septembre 2023, puis a été démonté professionnellement pour une remise en service rapide. L’espace nécessaire pour l’installation : environ.
utilisé
État : utilisé, Fabricant : Gram Equipment, Hauteur totale : 1 850, Longueur totale : 2 100, Largeur totale : 630, Remarques : Le congélateur glacé continu GIF-2000 (fabriqué en 2008) de Gram Equipment est un congélateur haute performance pouvant fonctionner avec une capacité allant jusqu’à 2000 l/h. Le congélateur est principalement utilisé pour la glace ou la sorbet, mais peut aussi servir à refroidir ou congeler d’autres produits liquides comme le yaourt, la sauce, etc. Le système a été utilisé jusqu’en septembre 2023, puis a été inspecté professionnellement pour une rapidité
utilisé
Water connection: 1/2 inch RG, water pressure: 0.7-6bar, water connection temperature: 50°C, drain diameter: 40mm, wash tank capacity: 95l, wash water temperature: 60°C, wash pump power: 2kW, wash pump capacity: 600l/min, wash pressure in the nozzles: 1.4bar, rinse tank capacity: 13l, rinse water temperature: 85°C, rinse pump power: 0.37kW, rinse pump capacity: 350l/min, rinse pressure in nozzles with rinse pump: 0.8bar, wash programs: 2, 4 and 6min, washing volume: 635x690x610mm, noise level: 70dB(A), water consumption per wash cycle: approx. 6l, heating element power: 2x 6kW + 1x 4.5kW, fuse protection: 32A, working height: 906mm, internal opening dimension: 508.5mm, length: 1265mm, width: 805mm, height opened: 2030mm, net weight without water: 225kg, gross weight without water: 250kg. An on-site inspection is possible, without power.
utilisé
utilisé
Cream separator (Skimmer). Self cleaning. Machine comes with the bowl, motor (15 kW), motor cover, feet, cyclone and all inlet / outlet pipes., Additional features:, Excluding:, - Baseplate., - Waterbox with water valves., - Control panel., - Service tools for maintenance., Type of Machine: Cream Separator / Skimmer, Capacity: 12.000 liter per hour, Bowl speed: 4.450 rpm, Motor: 15 kW - 380 V - 50 Hz - 1.455 rpm - 29,1 A, Weight: 1.420 kg, Dimensions: 145 x 110 x 175 cm
1 système CIP complet pour les laiteries avec 5 CIP pression et conduites de retour et vannes automatiques NW 65 et 100 6 réservoirs horizontaux, debout sur 4 pieds, isolés, Diamètre 2,65 m, hauteur 3,40 m constamment mis à jour, avec le système de contrôle du Siemens S 7, dans 4 armoires de contrôle Année de fabrication 2001 avec 1 réservoir de stockage horizontal de soude caustique, double paroi, capacité 10 000 L avec une condensation noire en acide nitrique P100. Réservoir de stockage, double paroi, capacité 6 200 l
utilisé
Cream separator (Skimmer). Self cleaning. Machine comes with the bowl, motor (15 kW), motor cover, base plate with feet, outlet pipe instead of cyclone and all inlet / outlet pipes., Additional features:, Excluding:, - Cyclone, - Waterbox with water valves., - Control panel., - Service tools for maintenance., Type of Machine: Cream Separator / Skimmer, Capacity: 12.000 liter per hour, Bowl speed: 4.450 rpm, Motor: 15 kW - 380/400 V - 50 Hz - 1.460/1.465 rpm - 30 A, Weight: 1.420 kg, Dimensions: 145 x 110 x 175 cm
utilisé
This APV Gaulin 1056 MC 18-5TPSC homogeniser is a 3-cylinder machine which is designed for ± 4.500 liter per hour with a maximum pressure of 345 bar. The homogensier is equipped with 2-stages with puppet valve cylinder, both stages manual controlled. Manometer. Motor: 45 kW - 380 V - 98 Amp - 50 Hz - 1.465 rpm. Stainless steel cladded. Oil pumping system outside the machine., Type of Machine: Homogeniser, Capacity: 4.500 liter per hour, Stages: 2 Stages, Max. Pressure: 345 bar, Valve cylinder: Puppet valves, Product: Dairy, Piston diameter: 44 mm, Motor: 45 kW - 380 V - 98 Amp - 50 Hz - 1.465 rpm, Dimensions: 180 x 110 x 180 cm, Weight: 2.115 kg
utilisé
The testing device can measure even the smallest leaks in packaging (helium detection)., The device is little used and in good condition., Information from the manufacturer’s brochure:, The detection limit of < 10-8 mbar l/s of the CONTURA Z can only be determined by mass spectrometric, Analysis can be achieved with a test gas., However, when sensitive flexible packaging is exposed to such a pressure difference,, the sealing seams could be subjected to such severe stress that the package could even burst., Such stress is eliminated by the patented membrane chamber principle of the CONTURA Z²., Function:, The product to be tested is placed manually or automatically on the bottom membrane. When the lid, is closed, the test procedure is initiated automatically., During the evacuation, the pressure of the atmosphere pushes the highly elastic membranes against the, packaging, and the conto ...
utilisé
Le séparateur à tambour Eriez se compose d’un élément magnétique fixé sur un arbre en acier pour former une unité magnétique et qui reste immobile pendant le fonctionnement. L’unité magnétique est entièrement enfermée dans une coque cylindrique rotative en acier inoxydable.
utilisé
Séparateur de crème (écumeur). Autonettoyant. La machine est équipée de la cuve, du moteur (17 kW), du cache-moteur, de la plaque de base, des pieds et des tuyaux d’entrée/sortie avec indicateur de débit., Fonctionnalités supplémentaires : À l’exception : - Valves d’eau, - Panneau de contrôle, - Outils de maintenance pour l’entretien. Type de machine : Séparateur de crème / écumeur, Capacité : 7 000 litres par heure, Vitesse de la cuvette : 6,500 tr/min, Moteur : 17 kW - 380 V - 50 Hz - 1,445 tr/min - 34 A, Dimensions : 170 x 120 x 175 cm, Poids : 1,300 kg
utilisé
Carbide coating machine, carbide coating device -Manufacturer: Carbumatic, hard metal coating machine -Type: unfortunately without a type designation -Voltage: 3 x 220-380 V / 50 Hz -Power: 0.4 kWA -Transport dimensions: 470/470/H380 mm -Weight: 49 kg/piece