Производитель: ARBURG Модель: ALLROUNDER 680 Год выпуска: 2016 Тип машины: Машина для литья под давлением Электрические характеристики: - Рабочее напряжение: 400 В, 3 фазы, 50 Гц - Управляющее напряжение: 230 В ~ / 24 В = - Номинальный ток двигателя/нагрева: 76 А / 18 А - Общий номинальный ток: 94 А - Общая потребляемая мощность: 56 кВт Машина уже демонтирована Время работы: около 29 000 часов Узнайте больше здесь - / Свяжитесь с нами по адресу -
clamping force: 1300 kN injection volume: -- cm³ screw diameter: 45 mm platen size: 470 x 470 mm Condition: used, Specification: Horizontal injection moulding machine, Type: Allrounder 470 S 1300-350 Injection unit: - Screw diameter: 45 mm - Centring ring diameter: 125 mm - Shot weight max.: 210 g (PS) - Injection pressure: 1,840 bar Clamping unit: - Clamping force: 1300 kN - Opening stroke max.: 850 mm - Mould installation height: min. 275 mm - Mould mounting platens: 470 x 470 mm - Operating hours approx.: 91,000 - Core pulls: 1x - Valve gate: 1x pneumatic - Hot runner control points: 12x - Temperature control unit interfaces: 6x (20 mA) - Conveyor belt in the machine - Selector unit. available - Release for high temperature up to 450°C - Communication card for ProSeS interface available - Robot interface available. Technical pr ...
clamping force: 350 kN injection volume: 59 cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power ...
clamping force: 1.300 kN injection volume: 230 cm³ screw diameter: 45 mm platen size: 685 x 685 mm Condition: used, Specification: injection moulding machine for TPE - used including Koch dosing unit clamping unit: - clamping force: 1.300 kN - heating platen size: 685 x 685 mm - Clear distance between tie bars: 470 x 470 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 225 mm Injection unit: - Screw diameter: 45 mm x 18D - Injection volume max.: 230 cm³ - Injection part weight: 210 g/hp - Max. injection pressure: 1,670 bar - Screw circumferential speed: 75 m/min - Cylinder heating: 4x 2,200 W - Nozzle heating: 600 W - Connection value: 3x 400 V, 50 Hz - Electrical connection (back-up fuse): 100 A - Weight approx.: 6,3 ...
clamping force: 500 kN injection volume: -- cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: horizontal injection molding machine, - used injection unit: - Screw diameter: 25 mm - shot volume max.: -- cm³ - injection pressure approx.: 1290 bar - heating zones: 4 - Heating power: 4 kW clamping unit: - clamping force: 500 kN - opening stroke max.: 325 mm - platen distance max.: 550 mm - clamping platen size approx.: 400 x 400 mm - tie bar distance: 270 x 270 mm - pump motor: 15 kW - total power: 19 kW - operating voltage: 380V, 50Hz - Weight approx.: 1.870 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 700 kN injection volume: 103 cm³ screw diameter: 30 mm platen size: 432 x 310 mm closing stroke: 650 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
