bending speed: 2.1 m/min Bending capacity - square: 30x30 mm bending capacity - flat iron: 80x15 mm Bending capacity - flat iron on edge: 50x10 mm tube diameter: 1 oder 60x2 mm Shaft diameter - upper: 35 mm Shaft diameter - lower: 30 mm total power requirement: 0,75 kw range L-W-H: 650 x 500 x 1300 mm weight: 170 kg Standard features: - hardened special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 900 mm table load: 1.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1,1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-105 ° Tilting Speed: 30 sn min./90° dimensions: 2100x920x1100 mm weight of the machine ca.: 930 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mm plate thickness: 4,5 mm pre-bending: 4,0 mm min. dia.: 210 mm roll diameter: 140 mm weight of the machine ca.: 1530 kg dimensions of the machine ca.: 3220x1200x900 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 2100 мм: 7 мм: 6 мм, диаметр рулона: 190 мммин. Диаметр: 285 мм: 4 кВт: 3200 кг: 4000x1350x1500 мм Оборудование: моторизованная задняя регулировка ролика — цифровой дисплей — автоматическое коническое изгибание. - Ножный переключатель — устройства безопасности. Данные для этой рекламы были созданы с помощью ModulMWS — программного решения LogoTech oHG.
working length: 2050 mm : 2.0 mm max. wire thickness: 3.0 mm Underfloor: 110 mm motor strength: 165 mm motor strength: 22 kW bending speed: 5.2 mm/min length: 3150 mm height: 1150 mm width: 850 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 4100 mm plate thickness: 8,0 mm ST pre-bending: 6,0 mm ST diameter of upper rolls: 300 mm side roll diameter: 210 mm diameter of lower rolls: 270 mm total power requirement: 7,5 kW weight of the machine ca.: 9.930 kg. dimensions of the machine ca.: 6532 x 1730 x 1489 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMW ...
sheet width: 2600 mm plate thickness: 10,0 mm pre-bending: 8,0 mm diameter of upper rolls: 230 mm side roll diameter: 190 mm diameter of lower rolls: 210 mm total power requirement: 7,5 kW weight of the machine ca.: 5.560 kg. range L-W-H: 4.650x1.380x1.300 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMWS - the software solutio ...
sheet width: 2100 mm plate thickness: 8,0 mm ST pre-bending: 6,0 mm ST diameter of upper rolls: 190 mm side roll diameter: 150 mm diameter of lower rolls: 170 mm total power requirement: 3,0 kW weight of the machine ca.: 3.290 kg. dimensions of the machine ca.: 4042 x 1380 x 1254 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMW ...
sheet width: 1600 mm plate thickness: 15,0 mm ST pre-bending: 13,0 mm ST diameter of upper rolls: 230 mm side roll diameter: 210 mm diameter of lower rolls: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4225 kg. dimensions of the machine ca.: 4000 x 1300 x 1440 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulM ...
sheet width: 3100 mm plate thickness: 13,0 mm pre-bending: 10,0 mm diameter of upper rolls: 300 mm side roll diameter: 210 mm diameter of lower rolls: 270 mm total power requirement: 11,0 kW Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I - beam section - flat steel: 120 x 15 (d 750) mm I-beam section - upend: 60 x 10 (d 800) mm L-beam: 50 x 5 (d 1200) mm round material: 35,0 (d 800) mm bar material dia. max.: 70 x 2 (d 1200) mm square material: 50 x 40 x 3 mm bending speed: 4,3 m/min roll diam. toproll: 155 mm bore: 50,0 mm total power requirement: 1,5 kW weight: 320 kg range L-W-H: 730 x 830 x 1350 mm Exhibition machine from 2023 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-motorized ring/profile bending machine - machine base frame, with rear shelf - horizontal and vertical work possible - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conform ...
plate thickness: 2.5 mm throat: 260 mm distance between roll centers: 92.0 mm weight: 295 kg range L-W-H: 1200 x 700 x 1200 mm Exhibition machine from 2021 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - 3x pairs of beading and flanging rollers included in delivery - robust beading machine with motor-driven rollers - Lower shaft with adjustable stop - for the economical production of a wide variety of bead types - high accuracy thanks to precision-mounted shafts - Clearly arranged switching elements - Base frame equipped with storage compartment - powerful drive motor, even under continuous load - mobile foot switch for clockwise and counterclockwise rotation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 4.0 mm throat: 260 mm distance between roll centers: 132 mm stroke: 55.0 OW mm tool adaptor: Ø 35 mm, 12 mm Nut mm total power requirement: 3.0 kW weight of the machine ca.: 450 kg. range L-W-H: 1600 x 900 x 1200 mm Exhibition machine from 2022 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - 3x pairs of beading and flanging rollers included in delivery - robust beading machine with motor-driven rollers - hydraulic adjustment of the upper roller, with pressure gauge - Lower shaft with adjustable stop - for the economical production of a wide variety of bead types - high accuracy thanks to precision-mounted shafts - Clearly arranged switching elements - Base frame equipped with storage compartment - powerful drive motor, even under continuous load - mobile foot switch for clockwise and counterclockwise rotation The data fo ...
weight max. in kg: max. 1000 kg turning speeds: 0,18 - 0,58 U/min height: 976 - 1436 mm inclination: 0 - 115 ° table diameter: 895 mm voltage: 380 V total power requirement: 2,0 kW weight: 685 kg range L-W-H: 2414 x 920 x 1436 mm Exhibition machine from 2024 with only approx. 2x operating hours Condition NEW Special price on request The AK BEND SRH hydraulic welding positioner is ideal for welding, assembly and maintenance work. Positioning is done via a hydraulic rotation and tilting function. Description: - electro-hydraulic turning and tilting function - Fast handling of workpieces - Maximum productivity thanks to optimal working position - Lifting, tilting and turning workpieces in one clamping - Low idle times thanks to turning components - Maximum work performance thanks to comfortable working - Back-friendly working for the user Equipment: - Continuously variable speed adjust ...
I-beam section - upend: 120 x 25 (d 1600) mm bar material dia. max.: 140 x 3 (d 3000) mm L-beam: 100x100x10 (d 1600) mm square material: 140 x 40 x 3 (d 4000) mm I - beam section - flat steel: 200 x 35 (d 1000) mm bar material - diameter: 70,0 (d 800) mm tool taper: 100,0 mm 0: 315 mm turning speeds: 5,4 m/min. total power requirement: 11,0 kW weight: 2.240 kg range L-W-H: 1500 x 1650 x 2100 mm Furnishing: - electro-hydraulic ring/profile bending machine - Hydraulic lower/side roller adjustment for extra small bending radii - Lower/side roller can be delivered individually - 3x powered rollers - divided roller segments - Digital position display of the bottom/side rollers Display with TouchScree function - hardened tool holder (42CrMo4) - Machine base - 2x hydraulically adjustable side guides - Horizontal and vertical work possible - freely movable control panel - Pressure gauge / pres ...
I-beam section - upend: 100 x 20 (d 2100) mm bar material dia. max.: 100 x 3 (d 3000) mm L-beam: 80x80x8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm I - beam section - flat steel: 120 x 30 (d 600) max.140b mm bar material - diameter: 60.0 (d 1000) mm tool taper: 80.0 mm oil volume: 100 Liter turning speeds: 4.2 m/min. weight: 1600 kg range L-W-H: 1240 x 1375 x 1540 mm Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x hydraulically adjustable side guides - ...
sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll length: 1050 mm roll diameter: 90,0 mm min. dia.: 130,0 mm engine output: 1,1 kW weight: 570 kg range L-W-H: 1.800 x 800 x 1.130 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller The data for this ad was created with ModulMWS - the software solution of LogoTech ...
sheet width: 1250 mm plate thickness: 5.5 mm pre-bending: 5.0 mm roll diam. toproll: 140 mm min. dia.: 210 mm turning speeds: 5.7 U/min engine output: 2.2 kW weight: 1365 kg range L-W-H: 2020 x 900 x 1.200 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller The data for this ad was created with ModulMWS - the software solution of L ...
sheet width: 4100 mm plate thickness: 13,0 mm ST pre-bending: 10,0 mm ST diameter of upper rolls: 360 mm side roll diameter: 250 mm diameter of lower rolls: 330 mm total power requirement: 11,0 kW weight of the machine ca.: 16.000 kg. dimensions of the machine ca.: 6542 x 1677 x 1900 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with Mod ...
sheet width: 3100 mm plate thickness: 16,0 mm ST pre-bending: 20,0 mm ST diameter of upper rolls: 360 mm side roll diameter: 250 mm diameter of lower rolls: 330 mm total power requirement: 15,0 kW weight of the machine ca.: 13.200 kg. dimensions of the machine ca.: 5542 x 2100 x 1983 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with Mod ...
L-beam: 40 x 5.0 (d 500) mm I - beam section - flat steel: 80 x 15 (d 700) mm I-beam section - upend: 50 x 10 (d 800) mm round material: 30.0 (d 700) mm bar material dia. max.: 60 x 2 (d 1200) mm square material: 50 x 30 x 3 mm range L-W-H: 670 x 530 x 1350 mm weight: 185 kg total power requirement: 0.75 kW Exhibition machine from 2021 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-motorized ring/profile bending machine - horizontal and vertical work possible Machine head can be folded 90° - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conformity - Operating instructions in German The data for this ad was crea ...
sheet width: 2050 mm plate thickness: 4,5 mm max. plate thickness: 4,0 mm anbiegen roll length: 2050 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1530 kg range L-W-H: 3220 x 1200 x 900 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller The data for this ad was created with ModulMWS - the software solution of LogoTech oH ...
I - beam section - flat steel: 80 x 20 (d 1200) mm I-beam section - upend: 80 x 25 (d 2100) mm L-beam: 50 x 50 x 6 (d 1000) mm bar material - diameter: 40.0 (d 800) mm square material: 60x60x3 ( d 4000 ) mm rectangle: 80x30x3 ( d 6000 ) mm roll surface width: 177x60 (18x5 Nut) mm bar material dia. max.: 70 x 2.0 (d 1600) mm tool adaptor: 60.0 mm turning speeds: 6.4 m/min. oil volume: 80.0 Liter total power requirement: 4.75 kW weight: 1080 kg range L-W-H: 940 x 1260 x 1390 mm Exhibition machine from 2022 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscree ...
sheet width: 3100 mm plate thickness: 8,0 mm ST pre-bending: 6,0 mm ST diameter of upper rolls: 230 mm side roll diameter: 210 mm diameter of lower rolls: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 6.020 kg. dimensions of the machine ca.: 5142 x 1390 x 1300 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMW ...
I - beam section - flat steel: 80 x 16 (d 1200) mm I-beam section - upend: 50 x 15 (d 1000) mm L-beam: 50 x 5 (d 1200) mm round material: 40.0 (d 800) mm bar material dia. max.: 70 x 2.0 (d 1600 ) mm square material: 80x30x3 (d 4000) mm channels - flange: UNP 80 (d 800 ) mm bending speed: 4.4 m/min roll diam. toproll: 157 mm bore: 50.0 mm oil volume: 18.0 Liter total power requirement: 1.1 kW weight: 485 kg Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x manual ...
: 1050 mm : 5,5 mm : 5,0 mm roll diameter: 130 / 195 mm : 2,2 kW : 1050 kg : 2150 x 900 x 1200 mm - 2 central rollers driven by an electric motor - Swing-out upper beam - Conical bending device - separate control panel - self-braking main motor - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized rear roller adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Ширина листа: 2100 мм Толщина листа: 40 мм Предварительная гибка: 30 мм Диаметр верхнего вала: 390 мм Диаметр нижнего вала: 360 мм Диаметр бокового вала: 300 мм Общая потребляемая мощность: 22 кВт Вес машины: 17200 кг Габаритные размеры: 5060 x 2200 x 2180 мм
sheet width: 1050 mm plate thickness: 1,8 mm pre-bending: 1,5 upper roll diameter: 70 mm min. dia.: 105 mm total power requirement: 1,1 kW weight of the machine ca.: 320 kg dimensions of the machine ca.: 1700x700x1100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1550 mm plate thickness: 4,5 mm pre-bending: 4,0 mm roll length: 1550 mm min. dia.: 190 mm roll diam. toproll: 130 mm weight: 1265 kg dimensions: 2670x1110x1050 mm Domestic equipments: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - induction hardened rolls - motorized rear roller adjustment - Digital display for back roller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 16 mm pre-bending: 13 mm upper roll diameter: 330 mm lower roll diameter: 300 mm side roll diameter: 240 mm total power requirement: 11 kW Overall size: 5600x1650x1900 mm weight of the machine ca.: 10.600 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
