hbm 판금 가공 사용 판매를 위해

0: 680 x 450 x 430 mm operating pressure: 3 - 6 bar Air consumption: 250 l/min. weight of the machine ca.: 28 Kg : 0,76 x 0,5 x ,75 cm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 915 mm dimensions of grinding wheel: 200 mm work table:: 170x125 / 265x150 mm total power requirement: 0,5 kW weight of the machine ca.: 26 Kg dimensions of the machine ca.: 0,6 x 0,5 x 0,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Measuring amplifier, for flow meter, vibration measurement, display device, vibration measurement, monitor display -Manufacturer: HBM, industrial measuring amplifier -Type: PME MP60 -Number: 2 measuring amplifiers available -Price: per piece -Dimensions: 160/60/H145 mm -Weight: 0.9 kg

weight max. in kg: 800/400 kg stroke: 6/12 mm stroke speed: 5/8 m/min output: 1,25 kw connected load frequency: 230 V weight: 21 kg dimensions: 420 x 180 x 280 mm Due to the low installation height, the maximum lifting height remains available. Control with emergency stop. (required by law) Suspension with safety hook. Overload protection with slip clutch. Built-in limit switch. Collection bag for chain. Control console with 1.6 m cable. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 320 mm turning diameter over slide rest: 220 mm turning length: 600 mm turning diameter in the gap: 320 mm turning speeds: 60 - 1650 U/min centre height: 160 mm spindle bore: 38 mm tailstock quill taper MT: 3 MK connected load frequency: 400 V total power requirement: 1,1 kW weight of the machine ca.: 340 Kg dimensions of the machine ca.: 1,4 x 0,75 x 0,7 m Center lathe with: 3-jaw chuck 160 mm. 4-jaw chuck 200 mm. Faceplate 200mm Fixed bezel Continuous bezel 4-way steel holder. Halogen machine light Chip tray, chip protection wall Hardened and ground bed tracks Longitudinal and cross feed Complete coolant system Forage protection Set of change gears Machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 150 mm band length: 2000 mm band speed: 33 m/sec total power requirement: 4 kW weight of the machine ca.: 100 t dimensions of the machine ca.: 1,2 x 0,5 x 0,85 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 780 x 480 x 1050 mm weight: 79,5 kg : 6 St. The tool trolley is equipped with 6 storage drawers. The tool trolley is equipped with 2 normal and 2 swivel wheels, one of them with a brake. The tool trolley is fully lockable thanks to an integrated lock. Drawers can be locked per drawer. All drawers are equipped with a quick release and a cushioning fitted. Height-adjustable storage compartment behind the door. Central locking with 2 keys. Tool trolley is equipped with 155 pieces of tool parts: 3 pcs. Socket sets: 1/4 , 3/8, 1/2 . Ratchet ring spanner set from 6 - 22mm, Extension for socket sets, different allen keys from 1 - 10mm, Various screwdriver sets. Pliers assortment. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 780x480x105 mm weight: 79,5 kg : 7 St. Tool trolley filled with: 3 pcs. Different socket sets, double end wrench, Double ended ring spanners, wrenches, pliers different, Screwdrivers, Allen screwdrivers, files, hammersSaw, etc. Tool Steel: Chrome Vanadium 5 pcs. Drawers filled with tools 2 pcs. Drawers empty The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 745 x 525 x 915 mm weight: 93,5 kg : 7 St. Tool trolley filled with: 3 pcs. Different socket sets, double end wrench, Double ended ring spanners, wrenches, pliers different, Screwdrivers, Allen screwdrivers, files, hammersSaw, etc. Tool Steel: Chrome Vanadium 5 pcs. Drawers filled with tools 2 pcs. Drawers empty The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 16 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK2 spindle turning speed range: 50 - 2250 U/min : 320 mm : 145 mm table surface area: 500 x 140 mm connected load frequency: 230 V total power requirement: 0,5 kW weight of the machine ca.: 90 Kg dimensions of the machine ca.: 0,5 x 0,45 x 0,84 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content but without digital display The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding range: 2 - 20 mm sharp cornered angle min./max.: 90 - 135 Grad connected load: 230 V weight of the machine ca.: 8,6 Kg dimensions of the machine ca.: 0,35 x 0,2 x 0,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 780x480x105 mm weight: 79,5 kg : 7 St. Tool trolley filled with: 3 pcs. Different socket sets, double end wrench, Double ended ring spanners, wrenches, pliers different, Screwdrivers, Allen screwdrivers, files, hammersSaw, etc. Tool Steel: Chrome Vanadium 5 pcs. Drawers filled with tools 2 pcs. Drawers empty The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 1220 mm band speed: 1140 m/min. : 0,62 x 0,4 x 0,35 cm total power requirement: 1,5 kW weight of the machine ca.: 0,04 t dimensions: 0,97 x 0,67 x 0,37 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 1045 x 5050 x 1010 mm weight: 100 kg : 7 St. Tool trolley filled with: 3 pcs. Different socket sets, double end wrench, Double ended ring spanners, wrenches, pliers different, Screwdrivers, Allen screwdrivers, files, hammersSaw, etc. Tool Steel: Chrome Vanadium 5 pcs. Drawers filled with tools 2 pcs. Drawers empty The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 35 mm throat: 230 mm bore stroke: 125 mm spindle taper: ISO 40 spindle turning speed range: 115 - 1750 U/min : 560 mm : 175 mm table surface area: 1000 x 240 mm max. distance between table and spindle-nose: 375 mm connected load frequency: 400 V total power requirement: 0,85/1,5 kW weight of the machine ca.: 0,95 t dimensions of the machine ca.: 1,3 x 1,2 x 2,1 m Domestic equipments: automatic feed and handwheel. Drill chuck with MK4 holder Digital depth display Left / right switch. Emergency stop switch Pivot head swiveling Spindle protection. Small toolbox Machine base and X-axis feed optional. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 915 mm dimensions of grinding wheel: 100 x 915 mm work table:: 225 x 155 mm total power requirement: 0,44 kW weight of the machine ca.: 0,018 t dimensions of the machine ca.: 0,56 x 0,26 x 0,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 25 mm throat: 175 mm bore stroke: 50 mm : 16 mm spindle taper: ISO 30 spindle turning speed range: 50 - 3000 U/min : 380 mm : 175 mm table surface area: 700 x 180 mm connected load frequency: 230 V max. distance between table and spindle-nose: max. 320 mm total power requirement: 0,75 kW weight of the machine ca.: 150 Kg dimensions of the machine ca.: 670 x 550 x 910 m Drilling and milling machine with large table Digital display SINO 3-axis. Digital display quill stroke. 2 speed levels. Left/Right switch Pan head left/right 90° spindle protection. incl. tool box with various tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width: 300 mm material thickness: 2,0 mm : max. 90° Grad weight: 12 Kg dimensions: 400 x 250 x 100 m Combined sheet metal working machine with: - Bending, tool widths 25 - 50 - 75 - 75 - 105 mm. - Rolls, roll diameter 38 mm - scissors, max. 1015 x 1mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 30 mm throat: 200 mm bore stroke: 70 mm : 16 mm spindle taper: MK3 spindle turning speed range: 50 - 3000 U/min : 565 mm : 220 mm table surface area: 840 x 210 mm connected load frequency: 400 V max. distance between table and spindle-nose: max. 470 mm total power requirement: 1,1 kW weight of the machine ca.: 230 Kg dimensions of the machine ca.: 0,75 x 1,05 x 1,3 m Drilling and milling machine with large table Digital display SINO 3-axis. Digital display quill stroke. 2 speed levels. Left/Right switch Pan head left/right 90° Recording MC 3 - B16. Drill chuck 3 - 16 mm. spindle protection. Machine stand. incl. tool box with various tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 355 mm dimensions of saw-band: 3770 x 34 x 1,1 mm cutting speed: 20 - 80 m/min cutting width: 490 x 280 mm : 290 mm Impact energy: 250 mm : 230 mm : 180 mm connected load frequency: 400 Volt total power requirement: 2,2 kW weight of the machine ca.: 0,7 t dimensions: 1,43 x 0,72 x 1,7 m Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 790 x 460 x 960 mm weight: 70 kg : 7 St. Tool trolley with 7 drawers equipped with tools - The pull-out drawers are all ball-bearing. - The entire workshop trolley is lockable. - Drawer 1 1/4 premium ratchet. 1/4 knee joint 45 mm. 1/4 extension 100mm. 1/4 socket wrench 4, 4.5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13, 14 mm. 1/4 long buttons 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 mm. 3/8 premium ratchet. 3/8 knee joint 55 mm. 3/8 extension 150mm. 3/8 socket wrench 8, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19 mm. 3/8 long socket wrenches 10, 11, 12, 13, 14, 15, 17, 19 mm. 1/2 premium ratchet. 1/2 knee joint 75 mm. 1/2 extension 125mm. 1/2 Sockets 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 19, 21, 22, 24, 27, 30, 32mm. 1/2 Long Sockets 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 22mm. - DRAWER 2 Ring, ratchet and socket wrench set consisting of. Sockets 8, 9, 10, 11, 12, 14, 15, 16, 17, 19, 21, 22 ...

welding current: 20 - 60 A cutting capacity: 1 - 20 mm open-circuit voltage: 104 V Required air-pressure: min. 4 bar connected load: 7,9 kW connected load frequency: 400 V weight: 16 kg Dimensions (LxWxH): 480 x 260 x 360 mm Digital display. Surge protection. Plasma torch. Earth cable. Reducing valve with moisture separator. Equipped with IGBT technology Delivered without CEE plug. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 32 mm throat: 200 mm bore stroke: 70 mm : 16 mm spindle taper: MK3 spindle turning speed range: 50 - 3000 U/min : 220 mm : 425 mm table surface area: 700 x 210 mm connected load frequency: V max. distance between table and spindle-nose: 470 mm total power requirement: 1,5 kW weight of the machine ca.: 230 Kg dimensions of the machine ca.: 0,75 x 1,05 x 1,2 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,3 x 0,6 x 0,65 m Benchtop lathe with base cabinet 3-axis LCD digital display system fully assembled. Longitudinal feed. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. Clamping plate. 4-way steel holder. Clock for thread cutting. Drip tray Hardened bed tracks. Emergency stop switch. Forage protection Set of wheels. Appropriate tools. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 320 mm turning diameter over slide rest: 200 mm turning length: 900 mm turning diameter in the gap: mm turning speeds: 75 - 2000 U/min centre height: 160 mm spindle bore: 50 mm tailstock quill taper MT: 3 MK connected load frequency: 230 V total power requirement: 1,5 kW weight of the machine ca.: 0,29 t dimensions of the machine ca.: 2,0 x 0,8 x 1,56 m Professional lathe 3-jaw chuck 4-jaw chuck faceplate bezel fixed running bezel Quick-change steel holder with 4 cassettes Halogen machine light Chip tray, chip protection wall Hardened and ground bed tracks Complete coolant system feed protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 300 mm bore stroke: 120 mm spindle taper MT: 4 MK table:: 500 x 460 mm column diameter: 115 mm turning speeds: 75- 3200 U/min feeds: 0,1 - 0,18 - 0,26 mm/U total power requirement: 1,5 kW weight of the machine ca.: 350 kg range L-W-H: 2,2 x 0,8 x 0,7 mm Column drilling machine with: Thread cutting function. Digital depth display Coolant system 2 stage motor Spindle protection Swivel table Pivoting drill head LED lighting Packaging dimensions: 730x760x188mm Weight 340kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 320 mm turning diameter over slide rest: 200 mm turning length: 900 mm turning diameter in the gap: mm turning speeds: 75 - 2000 U/min centre height: 160 mm spindle bore: 50 mm tailstock quill taper MT: 3 MK connected load frequency: 230 V total power requirement: 1,5 kW weight of the machine ca.: 0,29 t dimensions of the machine ca.: 2,0 x 0,8 x 1,56 m Professional lathe 3-jaw chuck 4-jaw chuck faceplate bezel fixed running bezel Quick-change steel holder with 4 cassettes Halogen machine light Chip tray, chip protection wall Hardened and ground bed tracks Complete coolant system feed protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 290 mm turning diameter over slide rest: 170 mm turning length: 750 mm turning speeds: 75 - 2000 U/min centre height: 145 mm spindle bore: 38 mm tailstock quill taper MT: 3 MK tailstock quill stroke: 80 mm connected load frequency: 230 V total power requirement: 1,5 kW weight of the machine ca.: 0,34 t dimensions of the machine ca.: 1,3 x 0,75 x 0,7 m Longitudinal and transverse feed. 3-jaw chuck 160 mm. 4-jaw chuck 160 mm. faceplate 4-way steel holder with 4 pcs tool holders 2 pcs. bezels Machine light Drip tray Hardened bed tracks. Emergency stop switch. Feed protection Set of wheels. Machine tools. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 360 mm turning diameter over slide rest: 220 mm turning length: 1000 mm turning diameter in the gap: 380 mm turning speeds: 70 - 2000 U/min centre height: 180 mm spindle bore: 50 mm tailstock quill taper MT: 3 MK connected load frequency: 230 oder 400 V total power requirement: 1,8 kW weight of the machine ca.: 0.65 t dimensions of the machine ca.: 2,0 x 0,8 x 1,56 m Professional industrial machine 3-axis digital display 3-jaw chuck 180 mm. 4-jaw chuck 200 mm. Faceplate 280mm Bezel fixed Bezel rotating 4-fold steel holder. Halogen machine light Machine light Foot brake removable chip tray, chip protection wall Hardened and ground bed rails Complete coolant system Feed protection Machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 75 t stroke: 250 mm daylight longitudinal/sideways: 800 x 215 mm dayligth: 170 - 885 mm working pressure: 7,5 - 8.5 bar weight of the machine ca.: 0,45 t dimensions: 1,2 x 0,8 x 2,1 mm Hydraulic/pneumatic workshop press Cylinder can be moved sideways pneumatic foot pedal Winch for table height adjustment 2 pcs. pressing blocks CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 80 - 700 mm workpiece-spindlehead motor: 0,25 kW grinding wheel diameter: 125 mm turning speeds: 2850 U/min grinding range: -20 bis +20 Grad weight of the machine ca.: 12 Kg dimensions of the machine ca.: 700 x 400 x 300 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 300 mm bore stroke: 120 mm spindle taper MT: 4 MK table:: 500 x 460 mm column diameter: 115 mm turning speeds: 75- 3200 U/min feeds: 0,1 - 0,18 - 0,26 mm/U total power requirement: 1,5 kW weight of the machine ca.: 350 kg range L-W-H: 2,2 x 0,8 x 0,7 mm Column drilling machine with: automatic feed Thread cutting function. Digital depth display Coolant system 2 stage motor Spindle protection Swivel table Pivoting drill head LED lighting Packaging dimensions: 730x760x188mm Weight 340kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1020 mm plate thickness: 2,5 mm distance between columns: 1050 mm daylight opening: mm : 135 ° total power requirement: Handbetrieben kW weight of the machine ca.: 0,32 t dimensions of the machine ca.: 1,4 x 0,6 x 1,3 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: 125 mm clamping range: 220 mm clamping height: 46 mm clamping force max.: 4500 Kg weight: 42 kg dimensions: 670x185x120 mm Hydraulic machine vise The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

welding current: 30 - 200 A connected load frequency: 230 V weight: 3,6 kg Dimensions (LxWxH): 290 x 135 x 2600 mm Scope of delivery: TIG welding machine Buddy TIG 160 Electrode and earth cable 3m TIG torch ET 17 4m Gas hose with union nut The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 780x480x105 mm weight: 79,5 kg : 7 St. Tool trolley with 7 drawers. Tool trolley has two normal and two swivel castors with brakes. Tool trolley completely lockable with an integrated lock. Drawers can be locked per compartment. All drawers equipped with quick lock and soft-closing mechanism. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding range: 8 - 32 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 16 Kg dimensions of the machine ca.: 0,43 x 0,24 x 0,24 m Drill grinding machine: Additional station for grinding back the drilling cutting surface (clearance angle) 25tk. Collets ER 40 are included in the scope of delivery, these are also suitable for clamping intermediate sizes. For grinding twist drills made of HSS and Hard metals with a TiN layer of 8 - 32 mm. Rotor with precision ball bearings guarantees smooth running. Vibration-free running thanks to its heavy weight and rubber feet. Sharpening angle adjustable for all common twist drills. Package dimensions: 430 x 240 x 240mm. Weight 16kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

welding current: 15 - 40 A cutting capacity: 1 - 16 mm open-circuit voltage: 96 V Required air-pressure: min. 4 bar connected load: 3,6 kW connected load frequency: 230 V weight: 9,0 kg Dimensions (LxWxH): 371 x 153 x 232 mm Exhibition machine Inverter plasma cutter with accessories: Cutting torch with 4 m cable, earthing clamp with 2.5 m cable, air pressure gauge, Mask and brush. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 915 mm plate thickness: 1,0 mm distance between columns: 920 mm daylight opening: mm : 135 ° total power requirement: Handbetrieben weight of the machine ca.: 96 Kg dimensions of the machine ca.: 1170 x 400 x 480 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 225 mm dimensions of saw-band: 2480 x 27 x 0,9 mm table height: 935 mm cutting speed: 45 + 90 m/min : 225 mm : 145 mm : 90 mm : 150 x 245 mm : 190 x 150 mm capacity 60 degrees: flat: 120 x 90 mm total power requirement: 1,1 kW weight of the machine ca.: 0,24 t Dimensions (LxWxH): 1380 x 580 x 930 mm - With an output of 1100 watts, the device is ideal for processing hard types of metal. - Thanks to the emergency stop and automatic switch-off, you can work safely - The low-noise electric motor ensures a quiet working atmosphere - Comfortable buttons guarantee pleasant operation of the device. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

diameter: 150 mm height: 80 mm centre height: 105 mm weight of the machine ca.: 18 kg dimensions of the machine ca.: 300 x 80 x 200 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 199,5 x 67,5 x 64 mm operating pressure: 2,5 - 8,0 bar air consumption at 6 bar: 350 l/min weight of the machine ca.: 0,23 t dimensions: 2,10 x 1,30 x 0,88 m Duo blast cabinet 10 PET sheets to protect the windows 10 PET sheets to protect the fluorescent lighting 2 foot pedals 2 jet guns 6 ceramic nozzle inserts (6 mm diameter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 350 mm bore stroke: 180 mm spindle taper MT: 4 MK table:: 560 x 560 mm column diameter: 140 mm turning speeds: 50 - 1450 U/min feeds: 0,1 - 0,2 mm/U total power requirement: 1,5 kW weight of the machine ca.: 580 kg range L-W-H: 2,27 x 0,7 x 1,1 mm • machine base for clamping high workpieces • Digital Depth Gauge • Gearbox swivels 180 ° • silent running through geärtete, ground oil-cooled gears • Tapping Function • electromagnetic clutch for drill feed • automatic feed • electric drive for table height adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 915 mm dimensions of grinding wheel: 200 x 32 mm grinding wheel hole diameter: 30 mm total power requirement: 0,9 kW weight of the machine ca.: 35 Kg dimensions of the machine ca.: 620 x 540 x 300 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding wheel diameter: 250 mm connected load frequency: 230 V : 90 - 180 U/min weight of the machine ca.: 18 Kg dimensions: 470 x 300 x 440 m Knife sharpening device with variable speed Grinding wheel 250 x 50 x 12mm, grit 220 Leather disc 200 x 30 x 12mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

diameter: 200 mm height: 105/265 mm centre height: 105 mm weight of the machine ca.: 41 kg dimensions of the machine ca.: 400 x 330 x 310 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 610 mm work table:: 170x125 / 265x150 mm : 16 mm turning speeds: 2000 U/min roll diameter: 16, 23, 29, 41 und 53 mm total power requirement: 0,45 kW weight of the machine ca.: 114 Kg dimensions of the machine ca.: 0,6 x 0,5 x 0,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

range L-W-H: 780x480x105 mm weight: 79,5 kg : 7 St. Tool trolley with 7 drawers. Tool trolley has two normal and two swivel castors with brakes. Tool trolley completely lockable with an integrated lock. Drawers can be locked per compartment. All drawers equipped with quick lock and soft-closing mechanism. Tool trolley is equipped with 196 pieces of tool parts: 3 pcs socket wrench sets: 1/4 from 4 - 14mm, 3/8 from 6 - 22mm and Torx from E10 - E20, 1/2 from 8 - 32mm. Various screwdriver sets. Extension for socket wrench sets, various Allen keys from 1 - 10mm, various files. Ratchet ring spanner set from 6 - 22mm, ring spanner set from 6 - 22mm. Pliers range. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 150 mm band length: 1220 mm dimensions of grinding wheel: 225 mm work table:: 150 x 400 mm Table tiltable up to: 90 Grad table surface area: 150 x 130 mm connected load frequency: 230 V total power requirement: 0,75 kW weight of the machine ca.: 35 Kg dimensions of the machine ca.: 650 x 360 x 400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 16 mm throat: 180 mm bore stroke: 85 mm spindle taper: MK 2 spindle diameter: 47 mm spindle turning speed range: 320 - 3300 U/min : 230 mm : 100 mm table surface area: 420 x 155 mm connected load frequency: 230 V : 900 x 600 x 300 cm total power requirement: 0,75 kW weight of the machine ca.: 8o Kg dimensions: 0,7 x 0,7 x 0,8 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 75 mm band length: 2000 mm band speed: 30 m/sec total power requirement: 3 kW weight of the machine ca.: 70 t dimensions of the machine ca.: 1,2 x 0,5 x 0,75 m Belt sander with - Contact disc: 600 x 75 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding range: 2 - 13 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 10 Kg dimensions of the machine ca.: 0,35 x 0,2 x 0,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 1170 x 880 x 825 mm operating pressure: 2,5 - 8,0 bar dimensions: 1,33 x 1,24 x 1,77 m air consumption at 6 bar: 350 l/min weight of the machine ca.: 0,16 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 1170 x 580 x 580 mm operating pressure: 2,2 - 8,0 bar dimensions: 1,22 x 0,93 x 1,70 m air consumption at 6 bar: 350 l/min weight of the machine ca.: 0,15 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width: 1015 mm material thickness: 1 mm speed: von Hand weight: 240 Kg dimensions: 1420 x 600 x 750 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding range: 3 -28 mm angle adjustable from - to: horizontal 0-180 Grad angle adjustable from - to: vertikal 0-45 Grad angle adjustable from - to: negativ 0-52 Grad clamping range: 3 - 28mm mm 0: 5200 U/min connected load: 230 / 250 Volt / Watt wheel diameter: 100 x 50 x 20 mm weight of the machine ca.: 45 Kg dimensions: 0,5 x 0,4 x 0,4 m This grinder is ideal for regrinding tools such as end mills, drills, TIG welding needles and much more. comes standard with: Lathe tool accessories Drill accessories Accessories for milling 5C spring collet (4-6-8-10-12 mm) Clutch key 38-42 Grinding wheel wrench Allen key M3-M8 screwdriver Diamond grinding disc Ø 100 x 50 x 20 Grinding wheel: Ø 100 x 50 x 20 Diamond pen Spring collet: 3/16 - 5/16 - 3/8 - 1/2 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 45 mm throat: 230 mm bore stroke: 125 mm spindle taper: ISO 30 spindle turning speed range: 75 - 1600 U/min max. milling cutter diameter: 80 mm : 560 mm : 230 mm table surface area: 800 x 240 mm max. distance between table and spindle-nose: 460 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 320 Kg dimensions of the machine ca.: 1,0 x 0,8 x 1,45 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 130 mm capacity 90 degrees: square: 127 x 127 mm dimensions of saw-band: 1140 x 13 x 0,65 mm band speed: max. 144 m/min total power requirement: 1,1 kW weight of the machine ca.: 15 kg dimensions: 500 x 300 x 400 m Portable and removable metal band saw Special features Powerful with 1100 watts. Including 2 saw bands, work table and integrated LED lighting. With adjustable, variable handle. Light and handy. For universal work in the workshop, on the construction site or for private use. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 2000 mm band speed: 15/30 m/sec tube diameter: 20 - 76 mm angle adjustable from - to: 30 - 90 Grad connected load frequency: 400 V total power requirement: 2,5 /3,3 kW weight of the machine ca.: 0,19 t dimensions of the machine ca.: 1,2 x 0,75 x 0,7 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 125 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 0,75 kW weight of the machine ca.: 0,135 t dimensions of the machine ca.: 1,25 x 0,6 x 0,6 m Speed in 6 levels 125 - 2000rpm. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. (Independent) Fixed bezel. Revolving bezel. 4-fold steel holder. chip tray. back panel. spindle protection. Hardened bed rails. Longitudinal feed with left / right switching. Set of change gears. Associated Tools. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1270 mm plate thickness: 2,0 mm distance between columns: 1300 mm daylight opening: 48 mm : 135 ° total power requirement: Handbetrieben weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,6 x 0,9 x 1,2 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 275 mm bore stroke: 120 mm spindle taper: MK 4 turning speed range: 75 - 3200 U/min : 190 mm : 490 mm table surface area: 700 x 210 mm connected load frequency: 400 V diameter of hob: max. 80 mm total power requirement: 1,1/1,5 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 0,8 x 0,75 x 1,85 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,3 x 0,6 x 0,65 m Benchtop lathe 3-axis LCD digital display system fully assembled. Longitudinal feed. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. Clamping plate. 4-way steel holder. Clock for thread cutting. Drip tray Hardened bed tracks. Emergency stop switch. Forage protection Set of wheels. Appropriate tools. Base cabinet is optional The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 30 mm throat: 250 mm bore stroke: 130 mm spindle taper MT: 3 MK table:: 380 x 380 mm column diameter: 98 mm turning speeds: 75 - 3200 U/min feeds: mm/U total power requirement: 1,1 kW weight of the machine ca.: 220 kg. range L-W-H: 0,5 x 0,6 x 2,05 mm Gear drill Thread cutting device Left/right barrel Tilting work table. Lighting. 2 electric Speed levels. Depth stop. Gears run in oil. Packaging dimensions: 2100x400x710mm Weight 260kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 945 x 605 x 605 mm operating pressure: 2,2 - 5,5 bar dimensions: 1,0 x 0,61 x 1,65 m : 1300 x 1000 x 750 cm Air consumption: 250 l/min. weight of the machine ca.: 0,09 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

connected load frequency: 230 V weight: 4,7 kg range L-W-H: 620 x 240 x 180 mm output: 0,8 KW grinding band dimension: 40 x 760 mm tube diameter max.: 180 mm band speed: 2,4 - 9,1 m/s Pipe grinding/finishing machine The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 32 mm throat: 200 mm bore stroke: 120 mm spindle taper MT: 4 MK table:: 290 x 270 mm column diameter: 92 mm turning speeds: 150 - 2450 U/min feeds: 0 mm/U total power requirement: 1,1 kW weight of the machine ca.: 95 kg range L-W-H: 0,66 x 0,8 x 1,7 m Column drilling machine with: ARBO / CE approved protective cover. Quick release chuck with pin. Tiltable work table. Deep stop. Ejector wedge. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 830 x 530 x 530 mm operating pressure: 2,2 - 5,5 bar Air consumption: 250 l/min. weight of the machine ca.: 50 Kg : 0,95 x 0,65 x ,7 cm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 125 mm capacity 90 degrees: square: 125 mm : 127 x 125 mm dimensions of saw-band: 1435 x 12,7 x 0,65 mm band speed: 38 - 80 m/min total power requirement: 0,95 kW weight of the machine ca.: 18 kg dimensions: 720 x 380 x 450 m Both straight and miter cuts can be made at angles between 45 and 90 degrees. With the metal band saw you not only work precisely, but also quickly: the band speed can be variably adjusted between 38 and 80 meters per minute. With a weight of only 25 kilograms, the saw can be used mobile. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 25 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK 3 spindle turning speed range: 50 - 3000 U/min : 280 mm : 155 mm table surface area: 500 x 180 mm connected load frequency: 230 V max. distance between table and spindle-nose: max. 320 mm total power requirement: 0,8 kW weight of the machine ca.: 150 Kg dimensions of the machine ca.: 670 x 550 x 910 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 45 mm quill stroke: 125 mm : 560 mm : 230 mm table surface area: 800 x 240 mm spindle turning speed range: 75 - 3200 U/min max. milling cutter diameter: 80 mm spindle taper: ISO 30 max. distance between table and spindle-nose: 460 mm throat: 230 mm connected load frequency: 400 V total power requirement: 1,5 kW weight of the machine ca.: 580 Kg dimensions of the machine ca.: 1,2 x 1,0 x 2,1 m Equipment: All axes with 3-digital display. Quill travel has separate digit display. Automatic feed in X-axis and quill. Motorized Z-axis. tapping device. coolant system. machine base. Collet set, SK tool holder. Further machine accessories in box. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 275 mm bore stroke: 120 mm spindle taper: MK 4 turning speed range: 75 - 3200 U/min : 190 mm : 490 mm table surface area: 730 x 210 mm connected load frequency: 400 V boring feeds:: 0,1 - 0,18 - 0,26 mm/U total power requirement: 1,1/1,5 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 0,8 x 0,75 x 1,85 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding wheel diameter: 250 mm connected load frequency: 230 V turning speeds: 90 U/min total power requirement: 0,2 kW weight of the machine ca.: 18 Kg dimensions: 470 x 300 x 440 m Knife sharpening machine Grinding wheel 250 x 50 x 12mm, grit 220 Leather disc 200 x 30 x 12mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 400 mm turning diameter over slide rest: 264 mm turning length: 1000 mm turning diameter in the gap: 550 mm turning speeds: 44 - 2000 U/min centre height: 200 mm spindle bore: 52 mm tailstock quill taper MT: 4 MK connected load frequency: 400 V total power requirement: 1,5 / 2,4 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,9 x 0,8 x 1,56 m 3-axis digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 320mm bezel fixed running bezel 4-fold steel holder. Halogen machine light machine light foot brake removable chip tray, chip protection wall Hardened and ground bed tracks Complete coolant system lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This 6-axis ERGOMAT TBC-42 Swiss Turning Machine was manufactured in 2012. It features a maximum material diameter of 42 mm and a spindle speed up to 5000 rpm. Equipped with a Fanuc 18i-TB Dual Path control, it offers precision and versatility with 8 tool positions and rapid feed rates up to 30 m/min. If you are looking to get high-quality turning capabilities consider the ERGOMAT TBC-42 machine we have for sale.Contact us for more information.

This ESCO Escomatic EC12 was manufactured in 2010. A Swiss type turning machine, its ideal for precision and efficiency in small part production. Contact us for more information about this machine.

This Gildemeister Sprint 20-8 was manufactured in 2010. It features a cooling system with a 600l capacity and 50µm filter, alongside a high-pressure pump option of 8 or 20 bar. The machine includes a Bristol B270/E oil mist separator and an IEMCA Boss 332E bar loader for 3m bars. With a chip discharge height of 1,250mm, its designed for efficient operation. Contact us for more information about this machine.

This Gildemeister Sprint 42 linear Lathe was made in the year 2006. It is equipped with a Fanuc 160i control unit. The machine has a spindle speed of 6500 rpm.

This TORNOS DECO 2000/13 was manufactured in 1999. It features a bar passage of 16 mm and supports up to 20 fixed and 16 rotating tools. Equipped with an IEMCA loader, CONVEYORS IND. ASS. conveyor, and additional oil filter tank, this machine ensures efficient operation. Consider the opportunity to buy this TORNOS DECO 2000/13 swiss type turning machine. Contact us for more information about this machine.

This STAR SR-20 R II Lathe was manufactured in the year 2004. It is equipped with a Fanuc Series 18i-TB control unit and has 7 axis. The machine has a spindle speed of 500-10000 rpm.

This 6-axis Citizen Cincom A20 was manufactured in 2018 and features a main spindle with a maximum bar diameter of 20 mm and a speed range up to 10,000 rpm. It includes a sub spindle and driven tools with a tool system supporting up to 21 tools. The machine offers rapid traverse rates up to 32 m/min and comes with an LNS Express 220 bar feeder. Consider the opportunity to buy this Citizen Cincom A20 swiss type turning machine. Contact us for more information.