ge jenbacher used for sale

Single Stand - Eccentric Press MÜLLER GEFREES Type PDET 5 S/EK Masch. No. Year of construction 1988 Compressive force 5 ton. Projection 125 mm Stand passage 170 mm Table surface 280 x 220 mm Waste hole 90mm Ram surface 160 x 100 mm Stroke adjustment 4 to 40 mm Ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping pin bore 25 mm Table height above corridor 900 mm Motor power 0.55 kW Mains connection 380 Volt, 50 Hz - pneumatic clutch-brake combination - electric foot switches - Control cabinet on the machine Space requirement L x W x H 900 x 600 x 1700 mm Weight 530 kg very good condition; used

Mechanical NC machine vice GERARDI precision machine vice, clamp jaw width 150 mm jaw height 40 mm wingspan 0 to 200 mm clamping pressure approx. 3 ton. Guideway height 50 mm Guideway length 420 mm- Mechanical machine vice - Quick adjustment with clamping ball lock - Clamping range via trapezoidal spindle approx. 60 mm- Stable base body ground on all sides- Horizontal, vertical or laterally clampable - Guideway with 14 and 16 mm Guide groove Dimensions L x W x H 420 x 150 x 100 mm Weight: 27 kg very good condition; used

: gebraucht : 2021 : 9648 : prompt, Zwischenverkauf v : Spanien : 15900 € : 1 : 60 to : 250 mm : 5 : 40 x 11 mm : 32 1/min : 350 x 15 mm : 120 x 10 mm : 45 / 40 mm : 10 mm : max. 150x10 mm : 5 kW : 2100 mm : 1400 mm : 1600 mm : 1390 kg DEMO MACHINE with bending station 5 working stations flat steel shear with device to reduce deformation angle iron shear with round- and squarebars opening triangle notcher punching station press brake device for flat steel table at flat steel station table at notching station length stop 1000 mm with contact switch, for angle, flat or bar station hydraulic drive 2 foot release User Manual in german + CE The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 0280 mm saw band length: 3660 mm cutting width: 0,9 mm capacity 90 degrees: square: 260 x 260 mm capacity 90 degrees: flat: 210 x 340 mm feed length: 500/2000 mm total power requirement: 3 kW weight of the machine ca.: 0,65 t dimensions of the machine ca.: 1,3 x 1,27 x 1,9 m Fully automatic horizontal band saw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 870 mm turning length: 3000 mm control: Siemens type: 810 mm bed width: 620 mm turning diameter over slide: 560 mm 3 jaw chuck Forckrath: 630 mm type: 3KTN 630 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Powder coating booth fully automatic with 2 x 4 automatic guns Very good condition, fully functional, in use. Year of construction 2009, until 2011 only used as an exhibition machine, from 2012 in normal use Dimensions powder parts WxH: 800mm x 1600mm (powder height can be extended on request) Powder Management System OptiCenter - Year of construction 2013 Powder part detection scanner to optimize the powder process Cyclone plant Filter system Fire extinguishing system

One Way Filling line for Beer Capacity: 4000 bph Installed for 0,33 liter Stubby Bottle, 0,33 liter Steinie Bottle Holdefleiss 24 head counter pressure filler with 6 head crowner model early 70. Fimer Rinser 16 head 3-4000 bph. Year? (From kahl Schlichterle 2016) Gernep Labetta labeler 6-480 SK 3-4000 bph. Year 1996? Depall. Dansk Maskinmontasje 2016 Side Grib Conveyor, Carry Line 2016 Bottle conveyors. Dansk Maskinmontage 2016

Freight lift according to MRL ConVer 147.01 with instructed accompanying person. Payload 1.200kg. 2 stops 0-4117mm. Car size 2800x2860x2000mm. Colour framework RAL 7043 Rest RAL 7035. Access bottom front top front and rear. Price without assembly, TÜV and freight, pure only the machine. The machine can also be adjusted on request, e.g. conveying height. Here, the selling price would then have to be determined.

Specifications: Tube outer diameter 124-230mm (4" - 8") Wall thickness 1 - 10 mm Power supply 200 - 240 V / 50 Hz infinitely variable speed 40 - 215 rpm. Speed stages electronic 1 - 6 Power 1800 W Feed module AVM 0.1 - 2.3 rpm incl. feeding unit and auxiliary unit used, in good condition.

Well-preserved Gestetner 411CD with powder, plush moisturizing

Hot-dip galvanized stacking frame for the installation of a water pump or aggregate., , If you are interested, please do not hesitate to contact us for a quote., , = More information =, , Year of manufacture: 2018, Applicable material: Water, Empty weight: 75 kg, Technical condition: good, Visual appearance: good, Damages: none, Please contact John van Tongeren (+31620537017) for more information, , = Dealer information =, , Aroused your interest? . The sales team will be happy to answer any questions you may have. CALL or EMAIL us, we are here for you! We would like to be your supplier ! Also for spare parts, pipes, hoses , coupling systems and fittings. A physical visit to our location is very well possible! Make your visit known in advance to avoid disappointment. Visit : from Monday to Friday from 08.00 to 17.00 on Saturdays or in the evenings by appointment.; Accessories: NL: Direct ...

Grinding length: 1000 mm Grinding width: 500 mm Grinding height: 500 mm Wheel diameter: 400 mm Spindle power: 16 kW X - Travel:              1000mm Y - Travel:              500mm Z - Travel:              500mm Table Length:            1000mm Table Width:             500mm Table load:              500 Feed rate X-Axis:        28000mm/min. Feed rate Z-Axis:        1000mm/min. Grinding stone dimensions:400 x 100 x 127mm Power:                   16kW Speeds:                  1400Rpm Feed rate Y-Axis:        10000mm/min. Lengt ...

Turning diameter: 870 mm Turning length: 3000 mm Turret positions: 0 CNC Brand: Fagor CNC Model: Fagor 8055 Work load between centrers 2800 Kg Fixed steady rest 2 x  Coolant system Quick chnage tool post Swing over bed Ø:        870mm Swing over cross slide Ø:560mm Swing in the gap Ø:      910mm DBC Turning Length:      3000mm Gap length:              325mm Spindle bore:            105mm Spindle power:           37kW Bed width:               550mm Tailstock spindle Ø:     140Ø Spindle taper:           5Mk Speeds / ranges:         1400Rpm Length:                &nbs ...

Hand - Bending bench Manufacturer: GEKA

Product number: 2580 Type: PlatForm Serial number: E010990205253 Year of construction: 2019 Platform height: 600 mm Steps: 2 pieces Dimensions: 2100 x 750 x 1700 mm

cutting diameter: 660 mm saw band length: 9000 x 54 mm cutting width: 1,6 mm Capacity 90° - round: 660 mm Capacity 90° - square: 650 x 650 mm Capacity 90° - rectangle: 650 x 1080 mm Capacity 45° - round: 660 mm Capacity 45° - square: 650 x 650 mm Capacity 45° - rectangle: 650 x 670 mm Capacity 30° - round: 410 mm Capacity 30° - square: 410 x 410 mm Capacity 30° - rectangle: 650 x 410 mm total power requirement: 5,5 kW / 2775 Nm weight of the machine ca.: 7100 kg dimensions of the machine ca.: 2500 x 2200 x 4500 kg The KSY 2DT 650 is a semi-automatic and column-guided horizontal bandsaw. The machine also has a driven roller table, which is 2 metres long on the front has a spray mist has a spray mist cooling system. Equipped with a linear guided saw blade, the KSY 2DT 650 can perform precise and fast Mitre cuts. Standard Specifications - Swarf Brush - Hydraulic Blade Guide - Hydr ...

cutting diameter: 550 mm saw band length: 6850 x 41 mm cutting width: 1,3 mm Control: Halbautomatisch Cutting area - square: 550 x 550 mm Cutting area - flat: 550 x 700 mm total power requirement: 4 kW / 1580 Nm kW weight of the machine ca.: 3775 kg dimensions of the machine ca.: 1850 x 1500 x 3450 m TThe KSY 550 x 700 is a semi-automatic and column-guided horizontal bandsaw. In addition, the machine has a driven roller table which is 2 meters long on both the front and rear sides. Optional Specifications - Motorized System For Roller Table - Laser Line - Extra Double Roller Table - PLC-Screen - Anti-Vibration System The pictures are for orientation only and do not represent a true-to-scale image of the machine. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 650 mm saw band length: 7730 x 54 mm cutting width: 1,3 mm Control: halbautomatisch Cutting area - square: 650 x 650 Cutting area - flat: 650 x 750 total power requirement: 5,5 kW / 750 Nm weight of the machine ca.: 4550 kg dimensions of the machine ca.: 2100 x 1550 x 3900 mm The KSY 650 x 1050 is a semi-automatic and column-guided horizontal bandsaw. In addition, the machine has a driven roller table which is 2 meters long on both the front and rear sides. Optional Specifications - Motorized System For Roller Table - Laser Line - Extra Double Roller Table - PLC-Screen - Anti-Vibration System The pictures are for orientation only and do not represent a true-to-scale image of the machine. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

diameter: 150 mm workpiece length: 1300 mm work piece width: 800 mm max. dia. of grinding wheel: 150 mm turning speed range: 0 - 2830 U/min work height max.: 945 mm milling-head swivable +/-: 180° engine output: 1,5 kW weight of the machine ca.: 230 kg. dimensions of the machine ca.: 1435 x 1100 x 1510 mm The Easy T is the cost-effective alternative to the conventional ones grinding and deburring machines. His head consisting of a grinding wheel and a flap brush, can be swiveled by 180°. Thus, a faster Switching between the aggregates possible. Due to the weight-bearing arm the head can be easily moved over the workpiece. The result is one even edge rounding. The pad also prevents slipping of the smallest components. Furnishing : - Deburring and rounding of laser-cut or stamped sheet metal parts - Grinding head, consisting of a grinding wheel & a flap brush, can be swiveled by 180°  ...

Control and feed spindle lathe Manufacturer Geminis Type GE870 Turning diameter 870mm Turning length 4000mm the machine also has a face plate 900mm and a fine bezel. Guides are very good, no wear to see. 400mm Forkardt wedge bar chuck 3 axis digital display Machine was stored about 3 years ago and is no longer used.

cutting diameter: 1100 mm saw band length: 12000 x 67 mm cutting width: 1,6 mm Capacity 90° - round: 1100 mm Capacity 90° - rectangle: 1100 x 1100 mm Capacity 90° - square: 1100 x 1300 mm total power requirement: 7,5 kW / 3100 Nm weight of the machine ca.: 12.000 kg dimensions of the machine ca.: 3300 x 3000 x 5300 mm The KSS 1100 X 1300 is a semi-automatic and column-guided horizontal bandsaw. In addition, the machine has a driven roller table, which is 1 metre long. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 180 t stroke: 400 mm table surface area: 1550 X 550 mm total power requirement: 7,5 kW weight of the machine ca.: 2100 t required space: 1,2 X 2,2 X 2,8 m Standard Equipments -Chrome Plated Cylinder -Steel Welded Frame -Oil Pressure Gauge -Pressure Adjustment -User Manual -2 Years Warranty -CE The HD 180 is manufactured for our sales brand GERD WOLLF Maschinenfabrik, by a renowned manufacturer from Türkiye. The engine is above the press (see photos). The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Centrifuge New brand: GESTER, model: CG-1200V. Shaft length: 1.2 m and axis diameter: 0.5 cm. Engine: 50 hp at 3000 rpm. Pneumatic piston for cleaning on top. Electrical panel with triangle star.

weight: 540 kg diameter: 1200 mm height: 1100 mm 0: 350 l total power requirement: 1,9 kW voltage: 350/50 V length in total: 1820 mm - with integrated manual separation ramp - control panel - Dosing pump for liquids - Capacity 382 liters - A soundproofing cover is also offered at extra cost! Sound insulation cover for VKUE 200 + The cover is controlled by a pneumatic piston + While the machine is running, the soundproof cover ensures for significant noise reduction. + It also prevents splashing of water or abrasives + It reduces noise emissions to less than 80 decibels. + The connection requires 6 bar General description: Our vibratory finishing system is suitable for: roughening, removing paint, decoating, deburring, derusting, descaling, de-oiling/degreasing, grinding as well as polishing and smoothing. The can also be used for non-metallic materials machine are used. Depending on the  ...

Packaging thermoforming machine (thermoformer, roll packing machine) characterized by the production of packaging from two rolls of foil. Depending on the type of machine and the foil used, the packages may be soft or hard. Machines intended for packing food and non-food products. Producer: CFS; Model: TIROMAT Compact 420; Year of production 2001; Working with soft foil; Bottom foil: +/- 420 mm (approx); Upper foil: +/- 410 mm (approx); Molding length: 430mm; Forming width: 380mm; Molding depth: 130 mm; Formats: 2.2; Length: 6700 mm; Width: 1100 mm; Height: 2000 mm; Weight: 1600 kg

weight: 1350 kg diameter: 1760 mm height: 1240 mm 0: 1210 l Vibratory Surface Finishing Machines With Separator VKUE series machines can be used for surface finishing of metal and nonmetal work pieces. These type of machines have large screen area and allow easy separation of work pieces from the grindstones. Optional Accesories - Pneumatic Sound Lid - Pneumatic Flap Control - Frequency Control - Dossage Pump - Magnetic Valve - Control Panel Base - Rinsing Pipe (Different Types) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 1000 mm plate depth: 1000 mm plate height: 310 mm weight: 975 kg dimensions of the machine ca.: 1000 x 1000 x 310 mm Clamping plates - T-slot plates 1000 x 1000 x 310 mm If you have not found the size you are looking for, you can also send us an e-mail with the completed PDF form. With this form we can produce an individual plate for you. Number of grooves: 3 edge distance: 185mm groove spacing: 140mm Groove width: 14mm Material: HT250 cast iron. Flatness less than 0,12 mm. Surface machined according to DIN 876/III 4 x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 1500 mm plate depth: 1000 mm plate height: 310 mm weight: 1330 kg dimensions of the machine ca.: 1500x 1000 x 310 mm Clamping plates - T-slot plates 1500 x 1000 x 310 mm If you have not found the size you are looking for, you can also send us an e-mail with the completed PDF form. With this form we can produce an individual plate for you. Number of hookers: 5 Edge distance: 135mm Hook spacing: 270mm Hook width: 28mm cast qualtity HT250 Flatness less than 0.12 mm. Surface processed according to DIN 876 / III 2x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 4000 mm plate depth: 1500 mm plate height: 310 mm weight: 4400 kg dimensions of the machine ca.: 4000 x 1500 x 310 mm Clamping plates - T-slot plates 4000 x 1500 x 310 mm If you have not found the size you are looking for, you can also send us an e-mail with the completed PDF form. With this form we can produce an individual plate for you. Number of hookers: 5 Edge distance: 14mm Hook spacing: 270mm Hook width: 28mm Material: cast iron HT250. Flatness less than 0.12 mm. Surface processed according to DIN 876 / III The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 1500 mm plate depth: 1500 mm plate height: 150 mm weight: 1300 kg Clamping plates - T-slot plates 1500 x 1500 x 150 mm If you have not found your desired size, you can also send us an e-mail send us an e-mail with the completed PDF form. With this we can to produce a customised panel for you. T-slots - width: 22mm T-slot distance: 220mm Number of grooves: 6x6 Edge distance: 114mm Casting quality HT250 Flatness less than 0,12 mm. Surface machined according to DIN 876/III 5x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity: Ø 140 - 250 mm sawing motor: 30 kW hydraulic motor: 5,5 kW Saw Feeding Servo: 3 KW Siemens Material Feeding Motor: 3 KW Siemens Saw speed: 30-80 rpm /min saw-blade dia.: Ø750 x 3,8 x 3,2 x 80 mm cutting range min.: 1000 mm cutting range max.: 7000 mm control: Siemens hydraulic: Rexroth Valve coolant: Pulverisiertes Schneidöl required space: 3500 x 8000 mm Saw speed: 30-80 rpm / U pro min weight of the machine ca.: 9000 kg GERD WOLFF GLS-250 #High-performance circular Saw From 10 to 250 Millimeters round material, within seconds, they cut steal ofall kinds with precision an ease. Equipped with a material feed system and components from Germany, we combine german with turkish mechanical engineering. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 1500 mm plate depth: 1500 mm plate height: 600 mm weight: / kg Clamping plates - T-slot plates 1500 x 1500 x 600 mm If you have not found the size you are looking for, you can also send us an e-mail with the completed PDF form. With this form we can produce an individual plate for you. Parameters can be combined as desired. Clamping plate : 1500 x 1500 x 600 mm T-slots - width: 28mm T-slot spacing: 140mm Edge distance: 40mm Number of grooves: 10 Casting quality: HT250 Flatness less than 0,12 mm Surface machined according to DIN 876/III 3x in Stock Assembly field - Test field - Assembly platform - Clamping plate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SECOND HAND SANDING MACHINE FOR TURNED PIECES GENINI MOD. LAR 90 - With automatic loader - No. 2 abrasive belts -Brushes - No. 6 spindles - Working length 900 mm

plate width: 900 mm plate depth: 600 mm plate height: 55 mm weight: 55 kg dimensions of the machine ca.: 900 x 600 x 50 mm Clamping plates - T-slot plates - Plate field 900 x 600 x 55 mm If you have not found the size you need, you can also send us an e-mail send us an e-mail with the filled PDF form. With this we can an individually manufactured plate for you. Number of grooves: 3 edge distance: 140 mm groove spacing: 270 mm groove width: 14 mm Casting quality HT250 Flatness less than 0,12 mm Surface machined according to DIN 876/III 20x on stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: - Flat steel shears cut up to 350 x 6 mm - 200 x 12 mm - Profile steel shears - cuts - L-steel at 90° to 80 x 8 mm - Bar steel shears - cuts - round steel up to 30 mm - Square steel up to 25 mm - punching force 380 KN - radius 175 mm - perforates in steel up to 27 mm Ø in 10 mm - Drive 400 V / 2.2 kW - Space requirement approx. W 500 x H 1280 x D 1000 mm - Weight approx. 900 kg

plate width: 2000 mm plate depth: 4000 mm plate height: 600 mm weight: 6700 kg lamping plates - T-slot plates - Plate field 4000 x 2000 x 600 mm If you have not found the size you need, you can also send us an e-mail send us an e-mail with the filled PDF form. With this we can an individually manufactured plate for you. edge distance: 112 mm Groove spacing: 225 mm groove width: 28 mm Casting quality HT250 Flatness less than 0,12 mm. Surface machined according to DIN 876/III 2 x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Copy Shaper / Copy Lathe Brand: Geiger Model: 8CD Milling + Grinding Workpiece length max. 1500mm

plate width: 3000 mm plate depth: 1500 mm plate height: 300 mm weight: 3580 kg dimensions of the machine ca.: 3000 x 1500 x 300 mm Clamping plates - T-slot plates - plate field 3000 x 1500 x 300 mm If you have not found the size you need, you can also send us an e-mail send us an e-mail with the filled PDF form. With this we can an individually manufactured plate for you. Number of grooves: 5 edge distance: 135mm groove spacing: 270mm groove width: 28mm Casting quality HT250 Flatness less than 0,12mm. Surface machined according to DIN 876/III 2 x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 2000 mm plate depth: 2000 mm plate height: 310 mm weight: 2930 kg dimensions of the machine ca.: 2000 x 2000 x 300 mm Clamping plates - Clamping cube - Plate field 2000 x 2000 x 310 mm If you have not found the size you need, you can also send us an e-mail send us an e-mail with the filled PDF form. With this we can to produce an individual panel for you. Number of grooves: 7 edge distance: 85mm groove spacing: 270mm groove width: 28mm Casting quality HT250 Flatness less than 0,12mm. Surface machined according to DIN 876/III 2x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 1500 mm plate depth: 4000 mm plate height: 300 mm weight: 4800 kg dimensions of the machine ca.: 1,5 x 4,0 x 0,3 m Clamping plates - T-slot plates - plate field 4000 x 1500 x 300 mm If you have not found your desired size, you can also send us an e-mail send us an e-mail with the filled PDF form. With this we can an individually manufactured plate for you. Number of grooves: 10 edge distance: 66mm distance between grooves: 22mm Casting quality HT250 Flatness less than 0,12 mm. Surface machined according to DIN 876/III 2x in stock The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

GEA PowerGrind Grinder 280 Robust industrial grinder Suitable for coarse and fine grinding of fresh and frozen meat. Applications include ground meat for formed products, sausages, minced meat, pet food and ground frozen vegetables.

Type: screw/piston Type of refrigerant: R404A Condition: excellent Product quantity: 18 pcs. GELPHA 7X-GK-33,5 (+7/-40°С - 3,4 kW) GELPHA 10X-GK-35(3 pcs.) (+7/-40° - 5,8 kW) GELPHA 15X-GK-40 (+7/-40°С - 7,7 kW) GELPHA 20X-GL2 50,8(2 pcs.) (-20/-40°С - 5,4 kW) GELPHA 40X-GL2-54(2 pcs.) (+7/-40°С - 22,8 kW) GELPHA 40X-GL3-57,5(2 pcs.) (-5/-40°С - 17 kW) GELPHA 40X-GL3-61,9(3 pcs.) (+12,5/-20°С - 21,07 kW) GELPHA 51X-GMR3-65,1 (-10/-40°С - 18 kW) GELPHA 180X-G9RR-66 (+7/-40°С - 76,7 kW/9,8 kW) GELPHA 50X-GL3-61,9(2 pcs.) (+7/-40°С - 29,8 kW/3,7 kW)

Used piston homogenizer. Producer: Gea Niro Soavi Model: Ariete NS3075 Year. 2011 Maximum pressure: 20MPa Capacity: 10000l/h A complete control cabinet with inverters is included with the device.

GEA CFS FlowCook HLT6000/600  Electrically heated. Hot air and steam. Belt width: 600 mm; Cooking length: 6000 mm Has previously been used for cooking burgers and nuggets in one factory and then on rental to a customer who was roasting trays of nuts. 

Technical data stationary waste compactor with weatherproof operator cabin Manufacturer Geesink Kiggen B.V. Type PD 26/20 Year of construction 2003 Pressing force normal 320 kN Pressing force during post-pressing 405 kN Theoretical capacity 350 m³/hour Cycle time approx. 27 seconds Volume bale chamber 2,6 m³ Volume per pressing cycle 2.2 m³ Press plunger flow in the container 320 mm Dimensions press plunger 740 x 1950 mm Filling opening 1,630 x 1,850 mm (L x W) Standard press opening for container 1250 mm Max. working pressure 330 bar Volume hydraulic tank 225 L Drive cable 11 kW Connection cable 5 x 4mm² Installation dimensions 4,300 x 2,495 mm Weight 3.500 kg Comments: We will not assume liability for the given technical data and possible errors.

Fut preserved Gestetner 411 CD with powder machine

plate width: 2000 mm plate depth: 1000 mm plate height: 310 mm weight: 1650 kg dimensions of the machine ca.: 2000 x 1000 x 300 mm Clamping plates - T-slot plates - panel array 2000 x 1000 x 310 mm If you have not found the size you require, you can also send us an e-mail send us an e-mail with the completed PDF form. With this we can can produce an individually manufactured panel for you. Number of grooves: 3 edge distance: 185mm groove spacing: 270mm Groove width: 28mm Casting quality HT250 Flatness less than 0,12 mm Surface machined according to DIN 876 Edge distance: 185mm Groove spacing: 270mm Groove width: 28mm Casting quality HT250 Flatness less than 0,12 mm Surface machined according to DIN 876/III The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 4000 mm plate depth: 1000 mm plate height: 310 mm weight: 3100 kg dimensions of the machine ca.: 4000 x 1000 x 300 mm Clamping plates - T-slot plates - plate field 4000 x 1000 x 310 mm If you have not found the size you are looking for, you can also send us an e-mail with the completed PDF form. With this we can to have an individually manufactured panel made for you. Number of grooves: 3 edge distance: 190mm groove spacing: 270mm Groove width: 28mm Casting quality HT 250 Flatness less than 0.12 mm Surface machined according to DIN 876/III The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.