1 mw gas used for sale

MWM TCG 2016 V 12 Exchange motor / short block with cylinder heads (biogas) Bücker + Essing short block with cylinder heads - crankcase in Exchange (tested according to manufacturer's specifications and repaired) - crankshaft in Exchange including new storage (tested according to manufacturer's specifications and repaired) - piston Squisch new -Liners with Coke wiper ring new -Connecting rods in Exchange including new storage (tested according to manufacturer's specifications and repaired) - cylinder heads in Exchange (tested according to manufacturer specifications and repaired) -Wheel drive including timing chest cover -Oil pump new including oil suction pipe -Oil pan -Oil cooler bundle (new) oil filter (new), closed oil circuit -Camshaft new incl. storage -Torsional vibration damper new -Flywheel housing and flywheel -including paint (RAL 5010) The here offered motor is ...

MWM TCG 2016 V 16 Exchange motor / short block with cylinder heads (biogas) Bücker + Essing short block with cylinder heads - crankcase in Exchange (tested according to manufacturer's specifications and repaired) - crankshaft in Exchange including new storage (tested according to manufacturer's specifications and repaired) - piston Squisch new -Liners with Coke wiper ring new -Connecting rods in Exchange including new storage (tested according to manufacturer's specifications and repaired) - cylinder heads in Exchange (tested according to manufacturer specifications and repaired) -Wheel drive including timing chest cover -Oil pump new including oil suction pipe -Oil pan -Oil cooler bundle (new) oil filter (new), closed oil circuit -Camshaft new incl. storage -Torsional vibration damper new -Flywheel housing and flywheel -including paint (RAL 5010) The here offered motor is ...

FOR SALE... OVERHAULED TURBOCHARGERS ABB VTR 254-11 & BBC VTR 214-11 TO WHOM IT MAY CONCERN; WE VE BELOW LISTED OVERHAULED & REPORTED TURBO CHARGERS AT OUR STOCK. READY TO TRANSPORT AND USE... ABB VTR 254-11 HZTL 428765P2 nNmax 523 nBmax 497 tMmax 680 C tBmax-650 C SFUSO1 YEAR OF BUILT 2010 MADE IN SWITZEWRLAND BBC VTR 214-11 NoHT 399285 their 635 Tmax 680 V 01113 R 012 H 04109 W 12206 E 03221 U 023 YEAR OF BUILT 2012 MADE IN SWITZERLAND IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CIONTACT WITH US. Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Agilent Gaschromatograph model 6890/G 1530A Detector FID/EPC, Injector S/SL /EPC HP-IB and Jetdirect card upon request with Autosampler and Agilent Chemstation

SUB: FOR SALE... USED 2 SET BBC COMPLATE VTR 714E-32 T/C AT TURKEY... EMERGENCY HAVE A GOOD DAY. .WE HAVE USED 2 SET BBC COMPLATE VTR 714E-32 T/C AT TURKEY. AND READY TO LOAD ON TRUCK. OUR T/C SPECIFICATION AS BELOW MOY 1988 SERIAL NO.: X. 140769 / 140770 V 01113 R - H 04010 W 05206 E 03010 U 03 I 01800 T 01100 BOTH T/C ARE IN VERY GOOD CONDATION. IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurlubay BEST of regards; Aliaga marine services E-mail: info@aliagamarine.com PHN/fax: + 90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

type RMG 980 200/100 Recon Part number: 1214 0250 Please note: We have various other RECON parts from different manufacturers and types available. We like to send you our current store reserves.

RECON Part number: 1214 1745 Please note: we also have other various RECON parts of different manufaturers / types in stock. We are pleased to provide you with our current stock list. ---------------------------------------------------------------------- ----------- If you have any further questions do not hesitate to contact us

MWM TCG 2016 V 12 Exchange unit with complete motor and generator overhauled on basic frame Payment by invoice warranty Bücker & Essing GmbH assumes the warranty exclusively for the delivery volumes supplied by it. A warranty for damages that are not directly related to the delivered and performed thing, as well as a warranty for consequential damages, are expressly not assumed. The warranty is assumed for a further 12 months at the most or until 8000 operating hours have been reached after commissioning, whichever of the two cases occurs first. Regardless of the commissioning date, the maximum warranty period is 15 months after delivery. The warranty case must be notified immediately in writing. Warranty claims can only be asserted if the commissioning and maintenance have been carried out and documented in accordance with the manufacturer's regulations. Commissioni ...

SUB: USED COMPLETE T/C BBC VTR 304-32 YOB 1996 HAVE A GDY SIR; WE VE COMPLETE USED COMPLETE T/C BBC VTR 304-32 AT OUR STOCK READY TO DELIVER AT IZMIR / TURKEY PLS FIND BACON AT BELOW VTR 304-32 NO. 5854 N MAX 450 C.. T MAX 620 C. YOB 08/1996 IF YOU INETEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

FOR SALE COMPLETE T/C ABB VTR 454-32 TO WHOM IT MAY CONCERN; WE ARE ABLE TO SUPPLY USED COMPLETE T/C ABB VTR 454-32 AT TURKEY PLS FIND SPECIFICATION T7C AT BELOW. TYPE VTR 454-32 HT 833511 N of Saad 290 Nbmax 276 t Saad 580 tbmax 550 YOB 2005 SWITZERLAND IF YOU'VE ANY QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

Further information on request

FOR SALE... 2 SET T/C TO TCR 18-42065 YOB 2010 AT TURKEY HAVE A GOOD DAY SIR. WE VE 2 SET COMPLETE T/C TO TCR 18 - 42065 AT OUR STOCK. PLS FIND TURBO CHARGER SPECT AT BELOW. TYPE: TCR 18 - 42065 WORK NO: 7642160 / 7642161 SPEED: 37300RPM T MAX: 650C. YOB: 2010 IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST of regards; Aliaga marine services E mail: info@aliagamarine

SUB: FOR SALE... BBC VTR 354A-32 COMPLETE T/C AND SPARE ROTOR AND SHAFT AT TURKEY HAVE A GOOD DAY SIR. WE VE COMPLETE USED BBC VTR 354A-32 T/C AT OUR STOCK WE VE SO ADDATIONALY SPARE 1 PCS COMPLETE ROTOR AND SHAFT. PLS FIND SPECT AND DETAILS AT BELOW.. BBC TYPE 354A-32 their 365 1/s No. HT 382239 tmax 620C. V 01116 R 012 H 04112 W 12108 E 03317 U 032 L 141 T 011 IF YOU'VE ANY QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best of regards; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

RECON Part number: C309460 ---------------------------------------------------------------------- ------- Please note: we also have other various RECON parts of different manufacturers / types in stock. We are pleased to provide you with our current stock list. If you have any further questions do not hesitate to contact us

HAVE A GOOD DAY SIR. WE VE NEW UNUSED. MITSUI MAN NA 57 TO 725 P IT STOWED AT FABRIQ WOODEN BOX. IT WILL NEVER MOUNTED AND USED. PLS FIND SPEC AT BELOW. READY TO TRANSPORT. EX STOCK. MITSUI MAN: NA 57 TO 725 P NO.: 2430 SPEC AD: 490 A4K : 404.3 REVOLUTION: 15000 RPM MAX TEMP: 600 C IF YOU'VE ANY FURTHER QUESTIONS PLS DO EMERGENCY HESITATE TO CONTACT WITH US. READY TO TRANSPORT. EX STOCK. Capt. Ayhan Ugurluba Best Regards ; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

Cylinder head for MWM TBG 620, TCG 2020 needed, not overhauled. Can we get over on request. Quantity: On request. Please note: We have various other parts of from different manufacturers and types available.

FOR SALE ...COMPLETE T/C NAPIER NA 457 AT TURKEY; HAVE A GDY SIR WE VE COMPLETE T/C NAPIER NA 457 AT STOCK. PLS FIND SPEC AT BELOW NA 457 701276 4FM157F 225 FJ 19500 650C. IF YOU HAVE ANY QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Kind Regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Electric pumping system for oil or diesel for controlled extraction of oil quantities from large containers such as oil barrels, tanks, etc. Consisting of electric motor with pump, pressure monitor, hose reel, pump gun with manual pass counter with rigid outlet. Display of the extracted quantity in litres Electric pump for fresh oil supply, suitable for barrel removal or as a tank pump, Closed hose reel for oil, hose length xxm xx" hose, with wall mount and pump gun. Special price

5,000 litre storage containers According to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. The tank has two saddle feet, a manhole DN 500 with domed lid, is used, inside empty and professionally cleaned and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube,. 1 sounding pipe provided with dip stick and sounding Rod seal, 1 vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fluid. The container is outside new primed and painted. L = 2.80 m / D = 1.60 m / weight CA. 1.3 tons. / free charged ex works. Description PTO pump: Non calibratable type eco-box-55- Capacity up to approx. 55 l / min. suitable for diesel fuel, incl. -Automated fuel dispenser with PC softwa ...

FOR SALE USED BBC VTR 2 354-11 P INLET COMPLETE TURBO CHARGER TO WHOM IT MAY CONCERN; WE VE COMPLETE USED BBC VTR 2 354-11 P AT OUR STOCK. TURBO DISMANTLED FROM MAK 8M 35 ENGINE ENGINE kW 4011 PLS FIND T/C AT SPEC BELOW BBC VTR 2 354-11 P 2 INLET HT 371508 V0111 3R011 H01111 W121 08E 03321 L181 CASING AA21 TURBO CHARGER IN GOOD WORKING CONDATION TURBO CHARGER READY TO TRANSPORT AT IZMIR TURKEY IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Make and Model: GE WHG-125 Year: 2011 Hours: 6000 approx. Year : 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: These units have been decommissioned and been in storage since May 2016. Unit 1 and 2 had a report of an MBC fault (magnetic bearing controller). Unit 3 has several parts missing due to a failure in the power electronics. Some parts of the Power electronics, PLC, speed drive for the refrigerant pump are missing. Unit 4 had a failed heat exchanger and filled the ORC with water, would need stripping to determine the full extent of the repairs needed. Extra: These units run on a working fluid (refri ...

Key data: 117

Make and Model: GE WHG-125 Year: 2011 Hours : 16,000 & 35,000 Capacity kW: 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: The containerised units were decommissioned towards the end of 2018. Both of the units were operational before decommissioning. Unit 1 has the upgraded 3600 MBC (magnetic bearing controller). Both of the units are containerised at present but can be removed. Extra: These units run on a working fluid (refrigerant R245Fa) that does not come with the units as this was sent for recycling after commissioning. This will need to be purchased and filled during installation and commissioning .  ...

Make and Model: GE WHG-125 Year: 2011 Hours : 7155 and 6849 Capacity kW: 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: These units have been decommissioned and been in storage since May 2016. Both of These units were operational at the time of decommission. Extra: These units run on a working fluid (refrigerant R245Fa) that does not come with the units as this was sent for recycling after commissioning. This will need to be purchased and filled during installation and commissioning. Price: €70,000 each

FOR SALE 2 SETS YOU NR 29 / S103A COMPLETE TURBO CHARGERS AT TURKEY... TO WHOM IT MAY CONCERN; WE VE 2 SETS COMPLETE TURBO CHARGERS TO NR 29 / S103A AT OUR STOCK TURBO CHARGERS DISMANTLED FM PROPOLSUION ENGINE. PLS FIND SPECT OF TURBO CHARGERS AT BELOW TYPE: ONE NR 29 / S103A WORK NO OF T/C: 1 150 804 / 805 PLANS NO.: H 09875 TURBO CHARGERS READY TO TRANSPORT AT IZMIR TURKEY IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

FOR SALE... OVERHAULED TURBOCHARGERS ABB VTR 254-11 & BBC VTR 214-11 TO WHOM IT MAY CONCERN; WE VE BELOW LISTED OVERHAULED & REPORTED TURBO CHARGERS AT OUR STOCK. READY TO TRANSPORT AND USE... ABB VTR 254-11 HZTL 428765P2 nNmax 523 nBmax 497 tMmax 680 C tBmax-650 C SFUSO1 YEAR OF BUILT 2010 BBC VTR 214-11 NoHT 399285 their 635 Tmax 680 V 01113 R 012 H 04109 W 12206 E 03221 U 023 YEAR OF BUILT 2012 IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CIONTACT WITH US. Capt. Ayhan Ugurluba BEST regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

We offer a generator set in a container with DEUTZ (MWM) engine - TBG 616 V12K. Engine is completely overhauled. Electrical power - 450 kW Built - 2001 Engine hours - approx. 63000 Bh Control - a new (approx. 2000 Bh) - Deif The complete CHP can be prepared and delivered at short notice. Without unit certificate!

Sealing plates 1.5 x 1.5 m from 2 to 8 mm thickness. Asbestos-free. Made in Germany Price â?¬ 2,00 / kg

10 tons Gaz hose (for house connection) 8 mm and 12 mm Complete roles Made in Germany â?¬ 2,00 / kg

GEA Plate heat exchanger NT50T CDS-10 with 10 plates in very good condition Material: 1.4405 Min./Max. permissible pressure: 0 bar / 6 bar (both sides) Min./Max. permissible temperature: 0.0 °C / 100 °C Test pressure: 7.8 bar Volume: 0.82 / 1.03 L Kerb weight: 83 kg Width: 320 mm Height: 670 mm Depth: 600 mm Connections: 2x Flange DN50 2x Flange DIN 11851 (milk pipe thread) Number of plates: 10 Last refrigeration/heat medium: water-glycol mixture Seals: EPDM

GEA Plate heat exchanger NT50T CDS-10 with 10 plates in very good condition Material: 1.4405 Built: 2007 Min./Max. permissible pressure: 0 bar / 6 bar (both sides) Min./Max. permissible temperature: 0.0 °C / 150 °C Test pressure: 7.8 bar Volume: 0.82 / 1.03 L Kerb weight: 88 kg Width: 320 mm Height: 670 mm Depth: 600 mm Connections: 2x Flange DN50 2x DIN 11851 (milk pipe thread) Last heat medium: steam Seals: EPDM

GEA plate heat exchanger VT10 CDS-16 with 10 plates in very good condition Built: 03/2006 Min/Max permissible pressure: 0 bar / 10 bar (both sides) Min./Max. permissible temperature: -10 °C / 100 °C Test pressure: 13 bar Volume: 3.0 / 3.3 L Kerb weight: 133 kg Width: 290 mm Height: 920 mm Depth: 570 mm Refrigeration/heat medium: propylene glycol Connections: 4x Pipe nipple DN 50 Device can be inspected at any time in 76694 Forest upon request.

We offer for fast CHP Scania DC12-16 motors/hull motors in exchange. MIW Motoren-Instandetzunsg-Werk GmbH North-West Ring 8 D-27404 Zeven/Germany E-mail= info at miw-zeven

We are stocked for CHP Fast with Scania Motor DC12/16 fuselage motors. MIW Engine Repair Plant GmbH North-West Ring 8 D-27404 Zeven/Germany e-mail: info at miw-zeven

WAUKESHA P9390GL 1 MW 400V / 50 Hz / 1000 rpm, only 6000 hrs, year 1996, dismantled from Landfill station

Fronius magicwave 2600, with wire feeder can be used for the robot welding. Machine is in great working condition, equipped with longines controls, wire feeder and welding gun connections for the robots.

Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 180 Connection voltage 1 x 230 volts Adjustment range 20 - 170 amperes Switch-on time 25% ED at 170 amperes 60% ED at 130 amperes 100% ED at 115 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 140 x 230 mm Weight 5 kg Age 12 months Condition workshop-tested, very good, as new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1 piece mains plug 230 V, ful ...

Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 160 Connection voltage 1 x 230 volts Adjustment range 15 - 160 amperes Switch-on time 25% ED at 150 amperes 60% ED at 90 amperes 100% ED at 80 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 150 x 240 mm Weight 6 kg Age 12 months Special accessories Carrying strap Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1  ...

Scania DC 12, complete engine It is a refurbished exchange engine. Repaired according to manufacturer's guidelines and according to RAL quality seals. - with exhaust manifold - with thermostat housing - with oil filler nozzles - Turbocharger as needed Installation, installation and service around engine and CHP optionally possible. Please contact us for a written offer.

Scania DC 12, fuselage engine It is a refurbished exchange engine. Repaired according to manufacturer's guidelines and according to RAL quality seals. - without exhaust manifold - without thermostat housing - without oil filler nozzles Installation, installation and service around engine and CHP optionally possible. Please contact us for a written offer.

MWM TCG 2016 V 12 exchange unit It is a complete, refurbished exchange unit (motor + generator + basic frame). Repaired according to manufacturer's guidelines and according to RAL quality seals. Further information on the scope and execution can be found on our homepage buecker-essing.de Installation, installation and service around engine and CHP optionally possible. Please contact us for a written offer. We also have other replacement engines, as well as AT cylinder heads, turbochargers, spare parts and other components in stock.

Sale MWM TCG3020V20 , 50 Hz, 10.5 kVA, standard scope of supply, unused , other questions/answers PM @

Capacity: 3000 kg Production capacity: 1500 kg/h degree: 1200 °c heating capacity: 1700 kcal/KW total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

MWM TCG 2016 V 8 Exchange Engine / Shortblock It is a refurbished replacement engine. Repaired according to manufacturer guidelines and RAL quality seal. Further information on the scope and design can be found on our homepage buecker-essing.de Out- and installation as well as service around engine and CHP can be optionally provided. Please contact us for a written quote. We also have other replacement engines, as well as AT cylinder heads, turbochargers, spare parts and other components in stock.

Power: 5000 kVA / 4000 kW Year of construction: 12/1992 Current: 275 A Voltage: 10.5 KV Frequency: 50 Hz Rotation: 1500 rpm Weight: Approx. 13.6 to. Protection class: IP 23 In 2017/2018, the following work was carried out: Stand winding in insulation class F completely renewed Inductor finely balanced and refurbished at nominal speed Reman refurbished plain bearings Other parts overhauled Tested and test run 2019 Prior sale reserved - errors possible

Recon Part number: 1230 0571 Attention: We also have various other RECON parts of different manufacturers / types available. We will be happy to send you our current stock list.

Specifications: - Welding current 600 A 45% ED 520 A 60% ED - 400 A 100% ED - Welding current adjustable - in 2 coarse stages and 10 fine steps from 50 A to 600 A - Digital Volt + Ampere display - 4 roller wire feed infinitely adjustable - Control M 100 for : - Two-stroke – four-stroke regulation - Interval welding - Spot welding - Stepless creep speed and wire backburn time - Intermediate package to the separate wire feed case approx. 4 lfm - Hose package approx. 4 lfm - Ground cable - Pressure reducer - Connection 400 V - Space requirement approx. W 650 x H 850 / 1250 x D 1100 mm - Weight approx. 280 kg

Control: P 2000 Technical data Max. temperature: 250 °C Execution: drying Working space: Width: 600 mm Height: 400 mm depth: 600 mm Power of the heating: 18 kW Ampere: 25 A Voltage 50 Hz 3x: 400 Volt Machine´s weight about: 250 kg External dimensions: Length: 800 mm Width: 800 mm Height: 1500 mm Various accessories: Ventilating / pulsated air

Technical data Max. temperature: 500 °C

Machine Type Electrode Inverter Welding Rectifier with bi-power setup Merkle brand Type MobiARC 284 cel Plant No. 106.539 Connection voltage 230/400 volts Setting range 20 – 280 amps Duty cycle 35 % ED at 280 Ampere 60% ED at 240 amps 100% ED at 210 amps Current adjustment infinitely variable weldable material thickness 7 mm Cooling inverter by built-in fan Special accessories Bi-Power setup Version portable mounting system Fuse 16 amps Dimensions L x W x H 485 x 200 x 435 mm Weight 17 kg Age 6 years Condition workshop tested, good, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece electrode cable 1 piece ground cable 1 piece hand shield 1 piece attachment glass 90 x 110 mm white 1 piece of protective glass 90 x 110 mm 10 DIN 1 pair of welder gloves with cuff 1 piece of ...