troester 押 出 機 中古 販売のため

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

roll surface width: 450 mm roll diam. toproll: 203 mm roll diam. bottom roll: 203 mm output: 8,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

screw ø:: für Extruder 90 mm screw length:: -- screw speedl:: -- U/min drive power:: 13,6 kW Condition: little used, as good as new Specification: gear pump ZP 75/50 for extruder size 90 - SEW helical gear units: R 97 - Siemens direct current motor: 1 GG5 118 - Drive power: 13.6 kW, 57 A - curved tooth coupling - With clamp for the head connection, - Clamping flange for extruder and head connection, - Base plate with linear guide rails, - Tooth shaft diameter: 75 mm - tooth width: 50 mm - helical gearing, hardened steel bearings, right-hand drive - without control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

90s cold feed extruder, GE 90 x 16 D Vac, make Troester, with large hose / profile spray head, drive 52 KW Siemens AC, 4 TCU Siengle

cold feed extruder - 60 mm x 18 D vacuum, with feed roller, drive 22 KW, screw speed 10 to 60 rpm, with gear pump, 5 TCU,

cold feed vacuum extruder Troester 90 mm x 18 D, with feed roller, drive 46 kW, pie speed 10 to 60 rpm, 5 TCU,

screw ø:: 90 mm screw length:: 16D screw speedl:: ca. 40 U/min drive power:: 48,5 kW Condition: used, overhauled to order, including warranty, including CE marking Specification: extruder – used with feed roller - Screw diameter: 90 mm - Screw length: L = 12D - Screw speed approx.: 40 rpm - Motor rated power: 48.5 kW - Belt drive, number of belts: 5 - Number of heating/cooling zones: 4 - Voltage: 3x 380V, 50Hz, N For further details, please refer to the attachment. Price on request, depending on design and customer requirements The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

This grinder has 2 fixed knives and 15 rotating blades. The motor power is 2.2 kW. The grid is replaceable, so the grain size can be changed. Everything works perfectly, motor, bearings, rotor, knife are fine. It's ready to use. I have several of them. There are also other document shredders for sale. Please also see my other ads.

This shredder has a large diameter rotor (30 cm) and 12 rotating blades. The motor has an output of 4 kW. This shredder is equipped with a torque increase gear (reducing gear), so it is also suitable for shredding thicker plastic waste. The grid is interchangeable, so the grain size can be changed. Everything works fine, motor, bearings, gearbox, rotor, blade are all fine. It can be used immediately. I have several of them. Other shredders are also for sale. Please see my other ads.

This grinder has 1 fixed blade and 3 rotating blades. The motor power is 2.2 kW. The grid is replaceable, so the grain size can be changed. Everything works perfectly, motor, bearings, rotor, knife are fine. It's ready to use. I have several of them. There are also other document shredders for sale. Please also see my other ads.

Guillotine-type mechanical shear for cutting plastic sheet in industrial processes. Brand: Jwell Cutting width: 1440 mm Maximum thickness: up to 6 mm Geared motor: 7.5 hp (5.5 kW) Type: Mechanical Guillotine Applications: - Cutting rigid or flexible plastic sheet - Post-process extrusion - Plate and film production - Preparation for thermoforming