We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
utilisé
80001350 de tour SMT La machine a été conçue et fabriquée pour produire des arbres de rotor pour les outils électriques. La machine est conçue et fabriquée pour effectuer automatiquement les opérations suivantes. - Chargez / déchargez automatiquement les pièces de / vers la ligne de porte-outils avec une unité de ramassage et de placement entre les extrémités de l’arbre. - Rotation du siège annulaire + commutateur rotatif plat + commutateur rotatif. - Montage en anneau - Côté commutateur - Montage en anneau - Côté roue motrice La machine dispose de plusieurs programmes de production pour produire différentes pièces. Chaque programme correspond de manière unique à un type d’onde Spécifications Longueur d’onde d’ancrage allant jusqu’à 92,5 - 163,1 mm Diamètre de la broche de roulement côté commutateur 8; 10; 12,5 mm Côté lecteu ...
utilisé
Tables pour presser hydrsulique pour le clampage sur la souche ou pour l’édition sur la table. Plusieurs disponibles. Les tables sont d’une presse 420to avec hauteur d’installation 1,250mm Les tables rondes ont une ouverture continue au milieu. Plus de données et de photos sur demande Prix spécial
utilisé
Description: Machine number: 1317-657 Basic functions: 4 zones (3 preheating zones, peak 1-stage with underside heating) Condensate trap in the bottom cooling zone Control system type C-Dias Technical data: Process chamber: Length: 3304 mm Preheating zones: 3 Peak zone (top / bottom): 2 heating modules / double peak (1 / 1) Bottom heating preheating zone (option): 2 Heated process length, total: 2081 mm Active convection section: 1533 mm Cooling zone length: 1223 mm Temperature detection: NiCr-Ni sensor in the gas flow Heating time: approx. 30 min Heat-up time with power limitation: approx. 60 min Heat transfer: 100 % forced convection Process temp. (preheating zone / peak zone): max. 300 °C / 350 °C (peak) Transport chain: Usable working width with LP support: 60 - 460 mm Usable working height LP support: Cam level / PIN level ... - 10 mm Free passage height (top / b ...
utilisé
Colored Steel Roll Forming Machine is mainly used in the production of colored steel sheets. The machine is artistically made and transmits smoothly at a low noise. It is a kind of very welcomed modern building material with better anti-press and anti-bending performance, and is widely used in the building of garden like factories, civil-construction and mansions, etc. Its length is set according to customerâs requirements and transportation situation. Its color is selected from the color code of the steel factory.
utilisé
Capacity: 700 t Table length: 5000 mm Table width: 5000 mm Stroke: 2000 mm CNC Brand: Siemens CNC Model: Siemens Simatic Playback Max. product5000 Ø Max. plaatdikte28 mm Max. bordel radius700 mm Min. product Ø800 Min.plaatdikte4 mm Min. bordel radius35 mm Werksnelheid190000 mm/min. Vermogen kW140 kW
utilisé
Capacity: 50 t Table length: 2200 mm Table width: 2200 mm Stroke: 800 mm Max. product2200 Ø Max. plaatdikte10 mm Max. bordel radius150 mm Min. product Ø800 Min.plaatdikte3 mm Min. bordel radius25 mm CNC Controll MIPC Q Playback with GAP control Large package TOP rolls 5 units Large package forming & pressure rolls 5 units Loading attachment Unloading attachment Under power out put 6 units Controllable forming roll drive Hydraulic displacement drive Clamping device without hole Basket bottem Knocker bottom Pressure vessel bottom Boiler bottoms Flat floor Plate base diffuser bottom Tank bottom Tank bottom Radar reflectors Engine parts Dispense air Silo hoppers Cooker hoods Container parts Hemispheres
utilisé
Épaisseur du matériau: 0 mmThroat: 7000 mm
utilisé
turning diameter: 720 mm turning length: 2250 mm control: CNCN 300 turning diameter over bed slide: 480 mm 3-jaw-chuck diameter: 650 mm total power requirement: 44 kW weight of the machine ca.: t dimensions of the machine ca.: m Voltage 380VHertz 503-jaw chuck ø (mm) 650 Including: Turret, 9 positionChip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
utilisé
diamètre de tournage: 720 mm dépendeur de rotation: 2250 mm contrôle: CNCN 300 diamètre de tournement sur glissière de lit: 480 mm 3-mâchoire-mandrin diamètre: 650 mm pousse totale requise: 44 kW poids de la machine ca.: t dimensions de la machine ca.: m Tension 380VHertz Mandrin 503 mâchoires ø (mm) 650 Comprenant: Tourelle, 9 positionsChante conveteur