We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
utilisé
Type de machine : Cisailles à guillotine Fabricant : RAS Modèle : 54.30 Année de construction : 1975 État : très bon Type d’offre : Machine d’occasion Spécifications: Capacité : 1040 x 4,0 mm Type d’entraînement : él./méca. Propulsion : 7,3 kW Remarque: guide parallèle, Supports matériels et butée à l’avant, 2 lames de rechange Poids : 2000 kg La machine est en très bon état et prête à l’emploi et peut être vue et démontrée par nos soins. Nous serions heureux si vous êtes intéressé par notre offre. Sous réserve d’erreurs, de modifications et de vente antérieure.
utilisé
Key data: 2040 mm, 2 mm
Type de machine : Cintreuse pivotante Fabricant : RAS Modèle : 2003 M État : très bon Type d’offre : Machine d’occasion Spécifications: Capacité : 2040 x 2,5 mm Type d’entraînement : él./méca. Propulsion : 0,75 kW Remarque: butée arrière, 5 rails de cintrage supplémentaires Poids : 1800 kg La machine est en bon état et prête à l’emploi et peut être vue et démontrée par nos soins. Nous serions heureux si vous êtes intéressé par notre offre. Sous réserve d’erreurs, de modifications et de vente antérieure.
utilisé
Offre 23317 Spécifications: - Largeur de travail max. 2040 mm - Épaisseur max. du matériau à 40 kP/mm², résistance 3,5 mm - Réglage de l’angle de pliage présélectionnable électroniquement de 0 à 135 - Plus petit rayon de courbure : 1,25 x épaisseur de tôle - Hauteur intérieure minimale 6 x épaisseur de tôle - Contrôle séquentiel automatique pour un flux de travail complet - Commande par commande manuelle ou au pied - Largeur d’ouverture maximale / course de la poutre supérieure 200 mm - Réglage de la hauteur - poutre de flexion 80 mm - la poutre inférieure 80 mm - Entraînement des feux de route 400 V / 1,1 kW - Entraînement de la poutre de flexion 400 V / 1,5 kW - La butée arrière manuelle peut être actionnée par l’avant - Encombrement env. L 3300 x H 1350 x P 1500 mm - Poids env. 2600 kg
utilisé
Key data: 1040 mm, 2 mm
Longueur de coupe max. : 1040 mm Epaisseur max. de la tôle : acier de 2,5 mm La butée arrière manuelle peut être actionnée de l’avant jusqu’à 500 mm Butée latérale Aiguisé au couteau Poids : 750 kg
utilisé
Key data: 1040 mm, 2 mm
Modèle 52.70 Spécifications: Longueur de coupe 1040 mm Epaisseur de la tôle en St 2,5 mm Épaisseur de la tôle en acier inoxydable (700 N) 1,5 mm Butée arrière motorisée jusqu’à 500 mm Fréquence de course env. 60 tr/min
utilisé
Key data: 1020 mm, 1 mm
Type de machine : Cintreuse pivotante Fabricant : RAS Modèle : 61.1 Année de construction : 1965 État : bon Type d’offre : Machine d’occasion Spécifications: Capacité : 1020 x 1,5 mm Type d’entraînement : manuel Remarque : Support matériel à l’arrière Poids : 220 kg La machine est en bon état et prête à l’emploi et peut être vue et démontrée par nos soins. Nous serions heureux si vous êtes intéressé par notre offre. Sous réserve d’erreurs, de modifications et de vente antérieure.
utilisé
Longueur utile 2040 mm Epaisseur maximale du matériau 5 mm
utilisé
Formeuse de serrure RAS type 22.15 Puissance : 2,2 kW Epaisseur maxi : 1,5 mm Diamètre de la roue : Ø 85 mm x 40 mm Tension : 380 V Dimensions (L x l x H) : 1700 x 600 x 1100 mm Poids : environ 350 kg
utilisé
Max. épaisseur de tôle: acier de 1,5 mm 2 stations continues (voir vidéo) Poids: env. 500 kg
utilisé
Max. épaisseur de tôle: acier de 1,5 mm 2 stations continues (voir vidéo) Poids: env. 500 kg
utilisé
Key data: 2040 mm, 2 mm
Max. longueur de coupe: 2040 mm Max. épaisseur de tôle: acier de 2 mm Rétrojauge manuelle réglable de l’avant jusqu’à 550 mm Maintien pneumatique en tôle Couteau aiguisé Poids: 1100 kg
utilisé
Longueur de flexion max. : 3 200 mm Max. épaisseur de tôle: acier de 2,5 mm Attelle de faisceau supérieur segmentée Mode de flexion manuel et automatique possible Réglage de l’angle de flexion via potentiomètre Poids: 3800 kg
utilisé
Longueur de coupe: 1020 mm Epaisseur de la tôle: 1,25 mm Taille de la table: 700 x 1150 mm Poids, approx.: 290 kg Équipement: -Tenir - Butée latérale avec réglage de l’angle et volant
utilisé
Longueur de coupe: 3150 mm épaisseur de tôle: acier de 4 mm Rétrogabarit contrôlé jusqu’à 1000 mm Longueur des butées latérales et des tables Limitation de la longueur de coupe Éclairage de bord coupé Mode d’emploi Poids env. 4200 kg
utilisé
N° 5129 : 1 gebr. Fermetures de pliage Fabr. RAS, type 700 M
utilisé
Longueur de flexion max. : 3200 mm Épaisseur max. de tôle : 4 mm acier Poids : env. 5800 kg Mwauag Claque arrière à commande motrice avec des cliquet jusqu’à 1500 mm Réglage des joues de pliage motorisés Commande Multibend 9000 Un outil segmenté avec pince automatique d’outillage (hauteur 150 mm)
utilisé
Vendre une table ciseaux, qui a été utilisé exclusivement pour la coupe en plastique. Fabricant RAS Type: 50.20 Besoin d’espace 2,5 m 1,1 m de haut Longueur de coupe 1020mm Nmyhr (Nmyhr) Épaisseur de coupe 1.25mm Poids 220kg
utilisé
Machine pliante RAS 22.11 - voir photos, Stand fold / double-standing fold
utilisé
sheet width: 2040 mm plate thickness: 2.00 mm thickness at Niro-steel: 1.25 mm no. of strokes: 63 Hub/min cutting angle: 1.10 Grad table height: 750 mm distance between columns: 2120 mm back stop - adjustable: 0 - 550 mm column arm: 100 mm Control: manuell engine output: 2.8 kW weight of the machine ca.: 1100 kg. range L-W-H: 2650 x 1980 x 1400 mm Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display adjustable from the front Continuous adjustment over the entire travel range Adjustment range 0.0 - 550 mm - Machine side stand with projection .. 100 mm - 1x hold-down bar - 1x long side stop with mm scale - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - Connection cable including plug - original instruction man ...
utilisé
largeur de la tôle : 3200 mm épaisseur de la plaque : 2,5 mm poids de la machine env. : 3,5 t Outils récemment mis à la terre. Présélection de l’angle de pliage par potentiomètre
utilisé
sheet width: 1250 mm plate thickness: 1 mm pre-bending: - shaft diameter: 56 mm weight of the machine ca.: 170 kg dimensions of the machine ca.: 1,5 x 0,55 x 1 m Manual 3-roller round bending machine with asymmetrical roller arrangement operated with hand crank via wheel transmission, upper roller can be swung out, lower rollers with annular groove, rear shaft adjustable for conical bending, front shaft adjusted via eccentric lever, rear roller adjusted via adjusting lever, rollers crowned. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
utilisé
Description: - Machine number: 188/9 - Useful length: 1020 mm - Sheet thickness: max. 1.25 mm weight approx.: 200 kg, Approx. Onsite Dimension. (l x w x h): 1,570 x 450 x 920 mm
utilisé
sheet width: 4040 mm plate thickness: 5,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 9,20 t dimensions of the machine ca.: m • Angle stop 1700 mm • Support arms according to photo • Backgauge controlled 1000 mm • pneumatic sheet metal holding device • automatic cutting gap adjustment • Small parts switch to the front • Control System 2005 • Rear safety light barrier Dimensions: L 4.8 x W 2.20 (plus support arms) x H 1.75 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
utilisé
Description: Technical details: Working width 2040 mm, sheet thickness 3.5 mm, stand width 2100 mm, sheet width 2040 mm, power 3.7 kw weight approx.: 2,300 kg, Approx. Onsite Dimension. (l x w x h): 3,350 x 1,350 x 1,350 mm
utilisé
plate thickness: 1,5 mm roll diameter: 76 mm bending speed: 4,7/9,4 m/min total power requirement: 0,37/0,55 kW weight of the machine ca.: 160 kg dimensions of the machine ca.: 0,6 x 0,6 m Electric 380 Volt: Universal flanging machine for raising rectangular shelves on straight, round and rectangular sheet metal parts. It has two flaring rollers, which in stand at a small angle of inclination to each other. The drive takes place via a flange geared motor that regulates two speeds in a pole-reversible manner. As a special accessory is an additional device for pressing in the cams for the cam standing seam available. The bending performance refers to 400 N/mm² strength. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
utilisé
sheet width: 2540 mm plate thickness: 2 mm strokes per minute until: 63 throat: 100 mm cutting angle: 1,13 ° table height: 750 mm table width: 320 mm table height over floor: 750 mm total power requirement: 3 kW weight of the machine ca.: 1600 kg dimensions of the machine ca.: 3,1 x 2 x 1,3 m Electric 380 Volt: Rear register front operated: 15 - 550 Foot switch: Squaring arm: Support arms: 3 x Motorized guillotine shears in the swing cutting system with adjustable from the front manual backgauge with analogue display and reading optics. Power transmission via gearbox, eccentric shaft and connecting rod on the cutter bar. Less noise level because the gear is only switched on during the cutting process is. Hold-down beam with continuous pressure element made of elastomers material that ensures secure clamping of the sheet metal. The cutting performance refers to 400 N/mm² strength. Ma ...
utilisé
sheet width: 2040 mm plate thickness: 3.0 mm thickness at Niro-steel: 1.5 mm no. of strokes: 50 Hub/min cutting angle: 1.4 Grad table height: 750 mm distance between columns: 2120 mm back stop - adjustable: 1.0 - 550 mm column arm: 100 mm Control: manuell engine output: 5.5 kW weight of the machine ca.: 2050 kg. range L-W-H: 2600 x 1980 x 1400 mm Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display adjustable from the front Continuous adjustment over the entire travel range Adjustment range 1.0 - 550 mm - Machine side stand with projection .. 100 mm - manual cutting gap adjustment - 1x hold-down bar - 1x long side stop - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - 2x EMERGENCY stop buttons at the front - ...
utilisé
CNC-controlled edge bending machine, manufactured by RAS Germany-Reinhardt Maschinenebau GmbH type 64.12 - 1280 x 3.5 mm. Thickness of bent steel sheet (St40) 3.5 mm; bending length 1280 mm. Setting the bending angle up to 28 degrees from the desktop. Jaw opening 300 mm. 2.2 kW drive. Weight 1180 kg. Full DTR documentation. Lots of additional tools, strips for flattening sheet metal.
utilisé
Edge bending machine manufactured by RAS GmbH Germany -type 74.40 4060 x 3 mm. Multibend 901 control, color, 2D graphics, bending simulation. Automatic setting of the bending radius depending on the material thickness. Super simple and intuitive control operation. Jaw opening 300 mm. Large bumper departure up to 1500 mm. 7.5 kW drives. Weight 6800 kg. Full O&M documentation, diagrams.
utilisé
This RAS FLEXIbend 73.40 Bending machine was manufactured in the year 2005 in Germany. It is equipped with a SYSTEM 6000 TOUCH control unit. The machine has a bending length of 4060 mm.