subcategorias
(terceiro nível de categoria)
Fabricante:
(Categoria: 1200)
Cleaning system, for ceramic flexo and ceramic flexo sleeves. Plastic media or sodium bicarbonate is sprayed at low pressure onto the the cylinder. This media is then recycled continuously about 8 times, depending granulometry. The machine consists of a cleaning and a cyclone/filtration filtration" section. Second-hand machine. Power supply: 230V 50/60Hz 3kW Compressed air: 5 bars Media consumption : 0.5kg/hour Find more here - / Contact us at -
2012 Envair CDC F 2G2D & 2012 REUKO Isolator and cleanroom Last filter change and last maintenance were on 09.01.2014 (see test report in the appendix) The air handling unit is designed for a room size of approx. 12 m2 (file room 3.46 in the appendix). The isolator has the complete documentation incl. test reports. It has been used very little (see current operating hours below) and is connected to an air handling unit (designed for approx. 12 m2). These are the technical parameters: REUKO climate service ENVAIR Isolator (Cytostatic isolator (CMR) 1.2m) a. Manufacturer: Envair Deutschland GmbH b. Type: CDC F 2G2D (2-Hand, Isolator clean room class A) c. Build: 06. 2012 d. Use: Reconstitution during 2 clinical trials (including cytostatics); idle operation for several months e. Details: isokinetic measuring probe, For the processing of: - Cytostatics - antivirals -hazardo ...
2019 WK Systemtechnik ILS 600 – HTL – Ionline Lubrication System Dickschickt preservation system. The oil is applied via nozzles The spray system is a minimum quantity spray system for high-precision dosing of preservative oil. With the spray system you can be coated or oiled reproducibly. By spraying using two-substance nozzles, the finest layer thicknesses can be applied without contact and a wide viscosity range can be covered. The forming medium is in a closed circuit; the excess pressure created by the spray air in the chamber is sucked off at the inlet and outlet using a vacuum lock, so there is no environmental pollution. General data Dimensions (WxHxD) without conveyor units 2486mmx2080mmx2722mm Dimensions with open doors 3265mmx3510mmx2722mm Weight approx. 2500 KG Electrical connection Supply voltage 400 Volt / 50 Hz Power 15kVA Fuse protection 35 A Control v ...
Windsor Klöckner W2700 - 27780 Injection Molding System Wittmann handling system included Injection Volume: - Strock volume: 20300 cm³ Clamping Force: - Schließkraft: 2700 kN Injection Pressure: - Einspritzdruck: 1360 bar Main Connection: - Network 1: - Voltage: 500 Volt - Frequency: 50 Hz - Total Power: 418 kW Cooling Water: - Volume: Not specified - Max Temperature: 32°C Weight: - Total Weight: Not specified Find more here - / Contact us at -
Manufacturer: BvL Series : Ocean RW Model: 1250 2T Year of Manufacture: 2019 General Data - Max Length: 1000 mm - Max Width: 750 mm - Max Height: 750 mm - Diagonal: 1250 mm - Max Load Capacity: 500 daN = 500 kg (even load distribution is required to avoid static issues) - Operating Voltage: 3 x 400 V, N+PE, 50 Hz Find more here - / Contact us at -
ALUKAP350 machine, manufactured in 2012 by K.SCHULTEN GMBH from Germany. The 2012 K. Schulten GmbH AluKap350 is a specialized industrial machine produced by K. Schulten GmbH, a German manufacturer known for its expertise in producing machinery and components for industrial applications, particularly in aluminum processing. The AluKap350 is typically associated with aluminum profile cutting and processing. Machines like this are designed to handle precision cutting and processing of aluminum parts, which are widely used in industries such as construction, automotive, and manufacturing. The model number, 350, might refer to specific technical characteristics, such as the cutting capacity, blade size, or processing capabilities. Key features of a machine like the AluKap350 could include: Precision Cutting: The ability to cut aluminum profiles accurately and efficiently. High Throughput ...
2019 Soft Energy Controls CES0007 Ranking machine End of line testing machine which sorts and grades cylindrical and prismatic battery cells. It is quite a specific piece of equipment, but it has some components that have value and could be repurposed in other machines. Originally from Japan. Main functions: DCIR testing and grading of cells Sorting of prismatic and cylindrical cells based on the cell grade into trays Find more here - / Contact us at -
SFC. Isolator SFC 10 CO2 Purification System manufactured by Thar Process. Purification SFC is a normal-phase chromatographic technique that uses CO2 as the main mobile phase. Find more here - / Contact us at -
2013 SEPARFLEX 250 A Automatic water separator Find more here - / Contact us at -
- SFE. Superfast 2x18L CO2 Extraction System manufactured by Thar Process. The supercritical fluid extraction system is designed to extract oil, oleoresins, and other ingredients which become soluble in supercritical CO2 at high pressure and temperature. SFC. Isolator SFC 20 CO2 Purification System manufactured by Thar Process. Purification SFC is a normal-phase chromatographic technique that uses CO2 as the main mobile phase. Find more here - / Contact us at -
Marver MV S-400 semi-automatic cutting table for flat glass Find more here - / Contact us at -
2008 Herco ACR SYSTEM 23-1000 ACTIVATED CARBON RECOVERY SYSTEM Gas recovery system The installation is 10 years old, has a max. adsorption capacity for 75 fridges per hour, with a suction capacity of 850 m³/h. It is a system with activated carbon adsorption, with desorption over a cryo-unit. Designated Application Scope of Application The delivered recovery plant is designed and manufactured for reclaiming propellants refrigerator recycling. The propellants, vaporized during the shredding process, are sucked off from the shredder and adsorbents in the recovery plant. Other applications are not provided. If the plant is used for other applications, only the user carries the whole risk for damages. General data Application : Propellant recovery Plant designation : Activated carbon recovery system Plant type : ACR-SYSTEM 23-1000 Year of construction : 2008 Technical data ...
"Lower piston press => table/stroke from bottom to top". Technical data Manufacturer: Hans Schoen Year of construction: 1997 pressing force: 500t table clamping area: 640mm x 800mm mounting height: 380mm stroke: 150mm Find more here - /
Intergas dosing unit DSD 500, type A, foaming unit and gas dosing station At the moment we have an intergas dosing unit for sale. This was a part of a project. Therefore the machine was used only very limited. - Operating hours: well below 100h - Weight: approx. 500kg Find more here - /
Painting line Dimensions: painting line with conveyor and PLC. inlet and ionization: 2300mm long x 1500mm wide x 1200mm high paint booth: 2000mm long x 4300mm wide x 3200mm high evaporation zone: 1600mm long x 1600mm wide x 1400mm high Oven: 4200mm long x 1600mm wide x 2300mm high supply air/exhaust air pipes: construction height approx. 1200mm Find more here - /
Demonstration system EVT AQUA - L for sale. Year of construction 2020 Equipped with the following options Goods movement Spraying device Surface drainage 2 x heated flood unit 2 x ultrasonic rod transducers 1.5 kW / 25 kHz each Return sieve 2 x fine filter 25 μm Hot air drying Vapour extraction via filter muck Automatic oil separation Technical data Cleaning medium: Water with cleaning additive Filling volume: 800 dm3 Heating capacity: 30 kW Connected load: 60 kW Compressed air: 6 bar Weight of the system: 3000 kg Throughput: 4 - 6 batches/h 250 kg/h Basket dimensions: 670 x 480 x 320 mm Plant dimensions: 2400 x 2000 x 2450 mm Operating mode: 1-3 shifts Possible Applications: - Water Treatment: - Industrial Water Purification: Designed for treating and recycling water in manufacturing or processing plants. - Wastewater Ma ...
2000 HAIDA INTERNATIONAL D-E 702-3000K40 Testing chamber Find more here - / Contact us at -
Screw diameter 30 mm Foundation plan / installation plan (see machine layout above in the appendix), an extra foundation for the plant was not poured here Operating hours 12455h on 28.01.2021 Automatic cycle counter 743558 processed material PBT-GF 30 Ultradur B4300 G6 Q16 black Find more here - /
Brand: Farmet Model: FE500 Condition: Used Extruder for soya, cereals and waste products for animal feed production. Extruder was used very little. Find more here - / Contact us at -
2012 Wachter Rotar 60 Back-up fuse: max. 65A Designation: Parts cleaning system E-connection 3x40v/50Hz Find more here - / Contact us at -
2012 Wächter ROTOR 60-2-Bad -- WACHTER CLEANING SYSTEMS Machine: Feeding height 9 5 0 m m Basket usable size LBH 600 x 400 x 300 mm width 1 300 mm Depth 1 600 mm Height2 200 mm ( other dimensions possible) 5. heating: Washing coils 6. drive Rhonrad: 7. belt skimmer drive 8. vapour condenser 9. Pneumatic lifting door 1 O. Automatic water level regulation 11. stainless steel basket with clamping cover VA 600x400x300mm. Mesh 6x6mm Oatum: 13.03.18 15kW 7,5kW 0,12 kW 0,04 0.45kW Basket optionally rotated, swivelled or without movement. Control system:SPS Kloeckner EASY Find more here - / Contact us at -
Three-phase oil transformer DIN 42500 The four impellers/ wheels are also exist and included the external dimensions are approx. Width 1.4 m Length 2.2 m Height to top edge of LV connection bolt 2.0 m Hermetic version with DGPT2 and Euromold plug connections Find more here - /
2010 Burkle RB A glue application machine purchased in 2010 The machine can either be resold or serve as a spare parts donor Space requirement: approx. 16x7.0m Connected loads: Nominal power 20Kw Main components: Heavy-duty chain conveyor, roller conveyor Gantry unit with vacuum pump Glue application rollers ALTEK lifting table type AEA-30.12 Machine list Basic equipment Item 10 Heavy-duty chain conveyor Item 20 Portal stacker Item 30 Roller conveyor with centring unit Item 40 Roller conveyor Item 50 Roller applicator Item 60 Platform for roller applicator Item 70 Roller conveyor Item 80 Angle transfer Item 90 Scissor lift Item 100 Working platform application area, manually adjustable Item 110 Glue feed Item 10 Heavy-duty chain conveyor Item 10 Heavy-duty chain conveyor For pallet feed A welded frame made of rectangular steel bars with height-adjustable feet. Th ...
Cold wall plasma system this system has only been put into operation and has not been in use since then. It is used to activate surfaces or can also be used for nitriding processes. The equipment is as good as new and has never been in full production Usable space diameter 800mm Usable space height 1100mm Max. load 1500kg Operating hours only approx. 250h. Technical data: Usable volume DM 800mm H1100mm Max. load 1500kg Max. process temperature 580°C Pressure sensors manufacturer Pfeiffer - Model: CCR 373 Mass flow controller manufacturer Alicat (Ar, N2, CH4, H2) Vacuum pump manufacturer Pfeiffer Duo 65M Plasma generator specification Find more here - / Contact us at -
2004 Kuka KR 125L90-2 TJ Operational hour: 36.700 Controller: KRC1 KR 125 L90-2 TJ | KR C1 Year of manufacturing: 2004 Controller type: KR C1 Maximum reach: 2.410 mm Payload: 125 kg External axes: Spare parts: robot type discontinued, spare parts availability limited Find more here - / Contact us at -
Resistance annealing machine This machine anneals (thermally straightens) stainless steel wires from 0.30 - 0.50mm). FUNCTIONAL DESCRIPTION: - The machine enables heating by direct passage of electric current through the wire through the wire (resistance annealing process). The device is equipped with 4 special power stabilisers for regulation, in combination with an optical pyrometer for temperature control and thermoregulation. - The simultaneous heating of the 4 wires takes place in a chamber saturated with inert gas by the electrical contact transmitted by two conductive V-shaped discs (short-circuit rollers). are transmitted. Two further V-shaped discs have the task of guiding the wires. - The system can be integrated into an existing automatic Scholl disc system, which, however, is not not included in the scope of delivery of the machine. Alternatively, the straightened ...
Plant for fire aluminizing steel wire The total length of the plant is about 56 meters A 01 Wire uncoiler Uncoiling device Uncoiling device A 02 Wire cleaning Electrochemical wire cleaning equipment Ultrasonic wire cleaning device A 03 Wire heating Inductive wire heating Control cabinet Inductive wire heating A 04 Melt preparation - preheating Pre-melting furnace Melting - low pressure furnace A 05 Wire coating Coating device view Coating device A 06 Wire cooling Cooling channel Wire . Quenching tank A 07 Wire - rewinding device Wire rewinding view Wire winder view 2 Total power in KW and total 631 KW 1 Current in A: 593 A Technical performance parameters: Steel wire: C < 1,0 %. Diameter 1,00mm . - 2,00mm Strengths < 1400 N/mm² Coating speed design: Wire diameter: 1,00mm -1,50 mm Maximum coating speed: 120 m/min Wire diameter: > 1,50mm - 2,00mm Maximum c ...
CTK 2200 Kaschieranlage: - Type: CTK 2200 - Nominal Width: 2,200 mm - Product Width: 2,200 mm - Working Height: 1,220 mm ± 50 mm - Processing Side: One-sided from above - Control Side: Right - Fixed Edge of Machine: Right - Machine Speed: 10 – 30 m/min - Max Production Speed: 25 m/min - Passage Height: 80 mm - Dimensions: - Total Width: 3,000 mm - Installation Length: 11,000 mm - Working Width: Max 2,150 mm - Height: 5,700 mm - Weight: Approximately 9,500 kg - Load Capacity: 80 kg - Maximum Cycle Speed: 10 cycles/min - Power Supply: 400 V / 50 Hz, 3 phases, and control voltage 230 V / 50 Hz + 24 V/DC In the event that the buyer wishes to laminate the panels on both sides, we can also offer a suitable stacking turner. Seen on the last picutre Find more here - / Contact us at -
