Maszyna do kształtowania przekładni TOS OHA 50A ze zmianą biegów
max. wheel diameter: 1000 mmgear width: 200 mmmax. module: 10 min. module: 0,5 max. dia. of teeth cutting: 1000 mmmin. dia. of teeth cutting: 75 mmtable diameter: 1000 mmboring diameter: 400 mmspindle stroke: 0 - 230 mmstroke position adjustment: 250 mmdistance between table / ram: 480 / 730 mmdia. of shaper cutter: 8 Zolltaper: Morse 5 tool taper: 1 3/4 Zolltotal power requirement: ca. 20 kWweight of the machine ca.: 11 tStandard version- Chip conveyor- Two additional tables with diameters of 850 mm and 1,500 mm- Several cutting tools- Set of interchangeable gears- Program for cutting in 1-2-3-4 passes/cycles- Program for spiral cutting- Several holders and clamps for workpiecesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Automat do przekładania zębat, 5A140
Maksymalna średnica koła: 1000 mm, szerokość przekładni: 180 mm, maksymalnie. moduł: 7 min. moduł: 0,5 min. skok taranu: maksymalnie 16 mm. Skok powietrza: 180 mm, otwór do zagrania: 160 mm, całkowite zapotrzebowanie mocy: 4 kWweight maszyny: ok.: 5,2 t×� średnicy maszyny: - mDane do tej reklamy zostały stworzone za pomocą ModulMWS – rozwiązania programowego LogoTech oHG.
Maszyna do cięcia zębatki STANKO 5140
max. dia. of teeth cutting: 2000 mmworkpiece dia.: 2700 mmmax. module: 22 mmRing thickness for internal gearing max.: 500 Control: Siemens 840D table diameter: 1500 mmtable hole: 500 mmTable rpm: 3,5 1/mintable load: 200 kNStroke length: 30-330 mmno. of strokes doubel-strokes per min.: 10 - 200 1/min.axis distance: 70 ... 1220 mmmax. radial velocity: 3000 mm/minweight of the machine ca.: 38000 kgEquipment/ accessories:- Intermediate plate between head and column: Center distance modified min. 0 mm max. 1500mm- column increased for axial stroke 1200 mm max. - Shaping head drive power 30 kW- spindle diameter 160mm- max. tool diameter 300mm- max. cutter wheel speed 10 1/min- Cutting speed 5 ... 45m/min- max. lateral offset 50mm- coolant device coolant tank capacity 2500 l- documentationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 630 mm, 8
Max. średnica zewnętrzna (przekładnia): 630 mm Max. średnica wewnętrzna (koło zębate): ok. 750 mm Max. szerokość zębów: 180–200 mm Max. moduł: 8 Skok udaru: do 220 mm Częstotliwość skoków: 47–300 uderzeń/min Uchwyt narzędziowy: MK 4 Moc napędu: ok. 8 kW Całkowita moc przyłączeniowa: ok. 10–12 kW njbmsww er hompw sjwk Masa maszyny: ok. 5.500–5.800
Max. średnica koła: 420 mmSzerokość przekładni: 120 mmMax. moduł: 8 min. moduł: 0,5 sterowanie: BWO 783 nr Liczba uderzeń: 32 - 800 Hub/minskok: 0-137 mmśrednica stołu: 400 mm średnica otworu stołu: 125 mmcałkowite zapotrzebowanie na moc: 50 kWwaga maszyny ok.: 9 twymiary maszyny ok.: 5,3 x 3,9 x 3,5 mSterowanie CNC Heckler und Koch BWO 783Dane do tej reklamy zostały utworzone za pomocą ModulMWS - rozwiązania programowego firmy LogoTech oHG.
Key data: 630 mm, 8
Używany popychacz biegów Lorenz S8/630 z wymiennymi kołami.
gear hobbing diameter - external: 1200 mmgear hobbing diameter - internal: 1200 mmgear hobbing width -max.: 260 mmcontrol: Liebherr PC-NC max. workpiece diameter: 1500 mmtable diameter: 900 mmtable bore diameter: 320 mmmax. table load: 95 kNpower capacity: 30 kWcoolant pump: 120 l/minAxial distance between thrust spindle - table: 0-820 mmShaping spindle diameter: 125 mmtool taper: SK 45 DIN weight of the machine ca.: 26 tdimensions of the machine ca.: 8,073 x 6,183 x 4,375 mStrokes: - Stroke length min./max. - 0 mm / 270 mm - Stroke length adjustability - 270 mm - Stroke rate (double strokes) - 10 to 270 DH/minEquipment/accessories: - Chip conveyor - Cutting wheel holder SK 45 DIN - Cooler - Technical documentationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 500 mm, 8
MASZYNA CNC .
max. wheel diameter: 380 mmgear width: 200 mmmax. module: 6 min. module: Control: SIEMENS Sinumerik 840D working area: - max. gear diameter: 380 mmmax. workpiece diameter: 400/ 600 (800) Außen innen begmax. gear width: 200 mmCenter distance between gear head and table center: -50 / 450 mmTravel range of the lifting position: 250 mmMax. module for straight gearing: 6 mmMax. axial travel: 250 mmwork table:: - table diameter: 400 mmtable hole: 150 mmmax. table speed: 30 1/mno. of T-slots: 6 St.Table equipped with hydraulic clamping device: - Multi-interface for pallet loading and zero-point: - clamping system in the working area: Shaping Head and Lift-off Cam:: - Drive power of face milling head: 37 kWMax. stroke rate: 600 DH/minFace milling head axis angle adjustment: +/- 0,5 °spindle cone: HSK-B100 DIN 69893 taper of shaper cutter: 60 work-spindle diameter: 110 mmStroke length, automa ...
Key data: 320 mm, 110 mm, 6
MAKSYMALNA ŚREDNICA 320
gear hobbing diameter - external: 1200 mmgear hobbing diameter - internal: 1200 mmgear hobbing width -max.: 260 mmcontrol: Liebherr PC-NC max. workpiece diameter: 1500 mmtable diameter: 900 mmtable bore diameter: 320 mmmax. table load: 95 kNpower capacity: 30 kWcoolant pump: 120 l/minAxial distance between thrust spindle - table: 0-820 mmShaping spindle diameter: 125 mmtool taper: SK 45 DIN weight of the machine ca.: 26 tdimensions of the machine ca.: 8,073 x 6,183 x 4,375 mStrokes: - Stroke length min./max. - 0 mm / 270 mm - Stroke length adjustability - 270 mm - Stroke rate (double strokes) - 10 to 270 DH/minEquipment/accessories: - Chip conveyor - Cutting wheel holder SK 45 DIN - Cooler - Technical documentationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
model to 5B 150P - średnica stołu wynosi 800mm - Maksymalny skok: 160 mm - sterowanie to Omron NS12 - osprzęt logiczny i czujniki: karty sterujące procesorami serii CS1 firmy Omron Rysunki elektryczne oraz instrukcje bezpieczeństwa i użytkowania zostały zaktualizowane w 2004 r. tak samo jak modernizacja
max. wheel diameter: 780 mmgear width: 130 mmmax. module: 8 / 10 table diameter: 510 mmtable bore diameter: 160 mmnumber of strokes (double strokes): 30 - 1500 DH/minControl: Siemens Sinumerik 3 distance table - lower edge of ram: 650 mmtable-size: 500 mmtotal power requirement: 36 kVAweight of the machine ca.: 8,5 tdimensions of the machine ca.: 4,9 x 3,65 x 3,8 mThe machine is suitable for:- Internal and external gear teeth in small quantities- Internal gear teeth in blind holes (non-through holes)- External gear teeth without run-out, as hobbing would not be possibleExamples of components are: Internal gear rings for planetary gears, drive shafts, clutch hubs...- Siemens Sinumerik 3 CNC control- Chip conveyorMachine was only used sporadicallyThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
1996 sinumerik 840C dostępne wideo
max. wheel diameter: 500 mmgear width: 125 mmmax. module: 8 ram stroke range: 135 mmmax.helical angle: 41 °table diameter: 500 mmno. of teeth: 12 - 300 total power requirement: 7,5 kWweight of the machine ca.: 6 t2021 completely overhauled and equipped with controls and new motors.suitable for internal & external gear shapingwith:- Control unit- chip conveyor- coolant- change gearsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
MAX DIAM 500, MAX MODUL 8 , MAX STROCE 125 , SINUMERYCZNY 840 D
max. wheel diameter: 100 mmgear width: 26 mmmax. module: 31 min. module: 0,1 Control: Siemens 840 D SLtotal power requirement: 45 kWweight of the machine ca.: 7 tdimensions of the machine ca.: 4x3x2,5 mGleason 100S gear shaping machinefor the production of internally and externally toothed cylindrical gears andother cylindrical workpiece circumference regularly occurringprofiles and moulds as well as for the production of profiles using thesingle part process.Technical data:Nominal workpiece diameter 100 mmLargest circumferential diameter 150 mmMachine nominal module approx. 3 mm(Guide value depending on the respective machining task.)Shaping spindle stroke speed range 0 - 3,000 1/minStroke position adjustment range (manual) 20 mmLargest toothing width 26 mmSmallest pitch height of the hydrostaticinclined guide 400 mmSmallest/largest distance between tool axis - 20/+ 180 mmand workpiece ...
Rowek zębatych 5140, produkcja w Rosji, z przekładniami zmiennymi
max. wheel diameter: 180 mmgear width: 45 mmmax. module: 4 min. module: 0,5 stroke length max.: 0 - 52 mmspindle taper: innen MK 4 table diameter: 160 mmtable bore diameter: 75 mmno. of strokes: 355 - 630 Hub/minfeed range: 0,008 - 0,4 mm/Hubdimensions of the machine ca.: 2,30 x 1,50 x 2,36 mpower capacity: 6 kWweight of the machine ca.: 2.500 kgYear of construction: Approx. 1970The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
MAX ŚREDNICA 750,MAX MODUŁ 10
Max. Pitch circle diameter External gearing: 300 mmMax. Pitch circle diameter internal gearing: 300 mmMax. Outer diameter of workpiece (equipment): 450 mmmax. module: 6 gear hobbing width -max.: 100 mmMax. Helix angle (with tool Ø 125 mm): +/- 45 °strokes - infinitely variable: 130 - 1300 Hub/minworkpiece weight: 1000 kgMinimum distance table top - tool spindle: -55 / +300 mmMaximum distance table top - tool spindle: 200 mmMaximum distance table top - tool spindle: 350 mmManual Upright side shift: +/- 25 mmManual swivelling angle of the tool spindle: +/- 0,5 °Max. Tool speed: 15 UpMMax. Workpiece speed: 27 UpMMax. Tool diameter: 7 Zollvoltage: 400 Vfrequency: 50 HzMax. Line power: 70 Atotal power requirement: 48 kWweight of the machine ca.: 11 tdimensions of the machine ca.: 4,27 x 3,11 x 2,87 mcontrol: Siemens Sinumerik 840 C table hole: 40 mmtaper in main spindle: SK 45 Gleason PFAU ...
max. wheel diameter: 180 mmgear width: 45 mmmax. module: 4 min. module: 0,5 stroke length max.: 0 - 52 mmspindle taper: innen MK 4 table diameter: 160 mmtable bore diameter: 75 mmno. of strokes: 355 - 630 Hub/minfeed range: 0,008 - 0,4 mm/Hubdimensions of the machine ca.: 2,30 x 1,50 x 2,36 mpower capacity: 6 kWweight of the machine ca.: 2.500 kgWith rack and pinion unitChange gear setYear of construction: Approx. 1981The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
2000 zł Max. średnica koła 750 mm szerokość koła zębatego 200 mm Max. moduł 10 min. moduł 1 min. średnica koła 30 mm Max. liczba zębów 300 min. liczba zębów 6 kąt spiralny zęba min/max 0 / 60 min. skok barana 0 mm Max. skok barana 225 mm średnica stołu 500 mm obciążenie stołu 0,8 t №. uderzeń 23,5 - 150 Piasta/min otwór stołowy 90 mm całkowite zapotrzebowanie na moc 7 kW masa maszyny około 3,8 t wymiary maszyny ok.
max. wheel diameter: 130 mmgear width: 25 mmmax. module: 4 min. module: 0,5 Control: Siemens 840 Dstrokes - infinitely variable: 500-2500 Hub/minstroke: 30 mmwork-spindle diameter: 85 mmtotal power requirement: 49 kWweight of the machine ca.: 11,5 tdimensions of the machine ca.: 6,4x4,5x4,4 mCounterhold without centerhydraulically operated counter arm andLinear guides.For automatic ring loader, with 4 stations The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 420 mmgear width: 120 mmmax. module: 8 min. module: 0,5 control: BWO CNCno. of strokes: 32-800 Hub/mintotal power requirement: 50 kWweight of the machine ca.: 9 tdimensions of the machine ca.: 5,3 x 3,9 x 3,4 mMachines increase 100 mm intermediate plateautomatic Hublageverstellung automatic Hublängeverstellung 5 axis controlled machine BWO last type C, D, X, Z, L axes are CNCThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
