切割直径：约 250 mm 切割直径：方形 230 mm 切割直径：扁平 280 x 200 mm 带锯片尺寸：2950 x 27 x 0.9 mm 锯行程：290 mm 机器重量约：610 kg 切割区域 0：圆形 250 mm，方形 230 mm，扁平 280 x 200 mm 切割区域 45：约 190 mm，方形 180 mm，扁平 180 x 210 mm 切割区域 60： 约 120 毫米，方形 120 毫米，扁平 120 x 130 毫米 2 锯切速度 本广告的数据是使用 ModulMWS 创建的 - LogoTech oHG 的机器管理。
MEP Multimatic SA8，1995年建造年份 钢筋矫直切割系统，全自动，功能齐全的系统，可立 使用 工厂仍在运行，可以演示
saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 105 mm capacity 90 degrees: flat: 180 x 70 mm capacity 45 degrees: round: 120 mm capacity 45 degrees: square: 100 mm capacity 45 degrees: square: 135 x 60 mm saw blade turning speeds: 1700 / 3400 U/min total power requirement: 1,5/2,2 kW weight of the machine ca.: 0,210 t dimensions: 0,9 x 1,4 x 1,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 230 mm : 230 x 230 mm saw band length: 2950 x 27 x 0,9 mm table height: mm band speed: 15 - 100 m/min total power requirement: 2,2 kW weight of the machine ca.: 1,2 t dimensions: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting diameter: 300 mm capacity 90 degrees: flat: 330 x 260 mm capacity 90 degrees: square: 260 x 260 mm capacity 45 degrees: flat: 270 x 200 mm capacity 45 degrees: round: 260 mm capacity 45 degrees: square: 250 x 250 mm capacity 60 degrees: flat: 170 x 170 mm capacity 60 degrees: square: 170 x 170 mm capacity 60 degrees: round: 180 mm turning speed range:: 40 / 80 m/min dimensions of saw-band: 3320 x 27 x 0,9 mm engine output: 1,5 / 1,8 kW weight: 670 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 355 mm : 350 x 350 mm saw band length: 4640 x 34 x 1,1 mm table height: mm band speed: 15 - 115 m/min total power requirement: 4,0 kW weight of the machine ca.: 2,8 t dimensions: 3,1 x 2,2 x 2,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 370 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 110 mm : 180 x 100 mm Working height: 925 mm saw blade turning speeds: 15 - 150 U/min total power requirement: 5,5 kW weight of the machine ca.: 0,615 t dimensions of the machine ca.: 1,4 x 1,4 x 2,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350 mm capacity 90 degrees: round: 115 mm capacity 90 degrees: square: 95 mm : 180 x 95 mm Working height: 925 mm saw blade turning speeds: 15 - 90 U/min total power requirement: 3,0 kW weight of the machine ca.: 0,68 t dimensions of the machine ca.: 0,8 x 1,0 x 1,85 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting diameter: 300 mm saw band length: 3320 x 27 x 0,9 mm table height: mm band speed: 40/80 m/min total power requirement: 1,5/1,8 kW weight of the machine ca.: 670 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 355 mm : 350 x 350 mm saw band length: 4640 x 34 x 1,1 mm band speed: 15 - 115 m/min total power requirement: 5,5 kW weight of the machine ca.: 2,8 t dimensions: 3,2 x 2,2 x 2,7 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350 mm capacity 90 degrees: round: 115 mm capacity 90 degrees: square: 100 mm capacity 90 degrees: flat: 130 x 80 mm capacity 45 degrees: round: 100 mm capacity 45 degrees: square: 85 mm capacity 60 degrees: flat: 90 x 80 mm clamping range: 130 mm turning speeds: 30 / 60 U/min dimensions of saw-blade: 350 x 32 x 2,5 mm total power requirement: 1,1 / 2,2 kW weight of the machine ca.: 0,22 t dimensions of the machine ca.: 1200 x 860 x 900 m Special price: instead of 3997, -EUR now 3399, -EUR Manual miter saw for miter cuts from 45 ° right to 45 ° left, with high sawing performance. Made of robust cast iron, practical and safe for every cut. Basic equipment: externally adjustable coupling Locking device with a vice Can be moved on a prismatic guide with an adjustable bar Fixed clamps of the vice with axial adjustment for clamping the workpiece in the immediate vicinity ...
saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 105 mm capacity 90 degrees: flat: 180x70 mm capacity 45 degrees: round: 120/110 mm capacity 45 degrees: square: 10/95 mm capacity 45 degrees: flat: 135x60 mm engine: 2,5 0: 1700 / 3400 U/min weight of the machine ca.: 600 kg dimensions: 2,0 x 1,5 x 1,7 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
规格： - 锯片尺寸 300 x 3.4 x 32 mm - 锯片转速 - 切割范围 - 在 90 左右 90 mm 或正方形 80 mm - 气动夹紧杆 - 物料补给机定位控制 - 单冲程可达约 1000 毫米 - 多冲程 - 带数控控制机电的旋转臂控制面板 - 莫特。除尘+移动式排屑 - 驱动 400 V / 1.1 kW - 空间要求约为 宽 2750 x 高 1800 x 深 2000 mm - 重量约 600公
MEP Shark 282 CCS 带锯 三速400V，两级电机，运行平顺。 从0到72转/分钟可以无限变速。 斜切角度可从-45度到+60度。 CCS（切割控制系统）液压下降辅助装置。 锯片压力表。 制造年份：2005年 意大利制造。 最大切割能力弹药：250毫米 最大切割能力方格：220毫米 最大夹紧开口：285毫米 锯片尺寸：2950 x 27 x 0.9 毫米 冷却泵带滤网放在底柜里。 机器尺寸：125 x 70 x 190 厘米 进料输送机尺寸：200 x 53 x 90 厘米 附带如图所示的配件
自动锯机MEP 320 AXI，技术信息不具约束力，机器需提前销售，圆切能 ：260毫米，矩形切割能力：320x000毫米，锯片尺寸：3 150x27x0.9毫米，速度范围：20 - 100米/1（无级），重量：1.000公
SEGATRICE AUTOMATICA a Doppia Colonna SHARK 350 NC HS 5.0 + Evacuatore Motorizzato a Paletta Segatrice a nastro automatica, a doppio montante, per eseguire tagli a 0° su acciai da costruzione, inox e legati, pieni e profilati, con dimensioni comprese in 350x350 mm. Di serie completa di: Evacuatore di trucioli motorizzato dragante, applicabile a destra o a sinistra della macchina. Regolazione della pressione delle morse. Alimentatore con rulli verticali per il contenimento delle barre. Macchina a controllo numerico CNC MEP 50-Windows CE” Based, progettato da MEP per l’automazione delle macchine di propria produzione. Ciclo di taglio taglio pulito” - L’alimentatore arretra la barra per evitare delle rigature sulla superficie tagliata quando il nastro torna in alto. Sistema di controllo a bus di campo con doppio microprocessore con collegamento seriale. Interfaccia uten ...
带锯床 MEP SHARK 281， 技术数据信息不具约束力， 机器需提前销售， 最大切割能力Ã： 250 mm， 最大切割能力： 280x200 mm， 锯片尺寸： 2950x27x0,9 mm， 锯条速度范围： 36 - 72 m/1， 锯片电机功率： 1,5 - 1,8 Kw， 工作平面高度： 950 mm， 重量： 370 Kg
COBRA 352 SX evo 半自动电动气动锯床，使用带电焊硬质合金板 （HM） 的刀片切割铝和轻合金。机器从右侧 45 个角度切割到左侧 45 个角度，头部从向左倾斜 0 到 45 个角度进行倾斜切割。带受控单轴微处理器的锯床， 有由MEP设计的最新一代半自动锯床控制器。操作： 过相对按钮启动循环，执行以下步骤：– 台钳关闭，电机启动 – 磁头向下执行切割 – 电机停止 – 磁头返回顶部位置，虎钳打开。 欧洲最优惠的价格为机电机器！索取报价！
SHARK 512 SXI evo，半自动电液锯切机，带4640x34x1，1 mm，× 可在0.极其通用的机器，可进行左切和右 60 次之间的切割。切割周期：定位棒材后，启动循环， 行以下操作：副关闭 - 电机启动 - 切割头下降 - 电机停止 - 头返回 - 副打开。CYLCE DOWN UP：在半自动循环中操作，新功能DOWN使头部和刀片电 在切割完成后停止，通过按下UP按钮，头部升回其起 点，然后打开虎钳。 要求每种型号的MEP机器，我们有欧洲最优惠的价
SHARK 281，手动带锯床从0到60左侧切割。几个特点：电气面 （接线完全可识别，备用，松键安全开关，主开关 变极开关，紧急停止，电机磁热过载，最小张力线圈 ，防止缺相，低张力安全装置（LTSD 24 V）.- IP55控制手柄。 欧洲所有机电设备的最优惠价格！索取报价！
SHARK 281 CCS（切割控制系统）手动带锯机从0到60左侧切割。除 手动切割模式外，锯切机还可以在没有操作员的情 下进行单次切割，使用头部重量控制 - 由液压制动器引导：切割后带停止。此时的框架被手 提升到所需的位置，以便重新定位杆以进行切割。 带气动虎钳 （MA） 的版本中，阀钳由手动控制阀（可选配踏板控制）打 /关闭。 欧洲最优惠的价格！
MEP AVT400 旋盖机 型号： 271221 2021， 不锈钢封盖机， 坚固且易于使用的封盖机，适用于将 ROPP、螺帽拧到带有螺纹颈的瓶子上。最大瓶子直径 195 毫米，最大瓶子高度 355 毫米，每小时可达 400 - 600 瓶，移动式，1 相
dimensions of saw-band: 3320x27x0,9 mm : 40/80 m/min : 335 mm capacity 90 degrees: round: 300 mm capacity 90 degrees: square: 260 mm capacity 90 degrees: flat: 330x260 mm : 260 mm : 250 : 270x200 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: square: 170 mm capacity 60 degrees: flat: 170x170 mm : 200 mm : 180 mm : 200x160 mm weight of the machine ca.: 640 kg dimensions of the machine ca.: 2140x1300x1950 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350x32x2,5 mm : 15-90 U/min vice: 190 mm capacity 90 degrees: round: 115 mm capacity 90 degrees: square: 95 mm capacity 90 degrees: flat: 180x95 mm : 90 mm : 90 mm : 90x90 mm : 110 mm : 95 mm : 125x95 mm : 110 mm : 95 mm : 125x95 mm total power requirement: 3 kW weight: 685 kg Overall size: 2050x1100x1800 mm turning speeds: 15/90 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350 mm dimensions of saw-blade: 350 x 32 x 2,5 mm cutting diameter: 115 mm stroke: 100 mm capacity 90 degrees: square: 95 mm capacity 90 degrees: flat: 180 x 95 mm capacity 45 degrees: round: rechts & links 110 mm capacity 45 degrees: square: rechts & links 95 mm capacity 45 degrees: flat: rechts & links 125 x 95 mm capacity 60 degrees: round: 90 mm capacity 60 degrees: square: 80 mm capacity 60 degrees: flat: 90 x 95 mm cutting speed: 15 / 30 / 45 / 90 m/min total power requirement: 2,6 kW weight of the machine ca.: 375 kg dimensions of the machine ca.: 1000 x 950 x 1800 mm Features: - With miter adjustment 60° left / 45° right - Coolant device - 2 speeds - Machine base - Operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
dimensions of saw-band: 3650 x 27 x 0,9 mm speed: 15 - 100 m/min vice: 335 mm capacity 90 degrees: round: 300 mm capacity 90 degrees: square: 260 mm capacity 90 degrees: flat: 330 x 260 mm capacity 45 degrees: round: 260 / 200 mm capacity 45 degrees: square: 250 / 180 mm capacity 45 degrees: flat: 270 x 200 / 200 x 160 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: square: 170 mm capacity 60 degrees: flat: 170 x 170 mm total power requirement: 2,2 kW weight: 1.105 kg dimensions: 2700 x 2300 x 1800 mm Fully automatic electro-hydraulic band saw with multi-micro processors and additionally semi-automatic, semi-automatic-dynamic and manual Function. - Automatic cycle (cuts from 0 ° to 60 ° link). CNC machine with two controlled axes that allow for the same material thickness 1000 various editing programs, each with a different cutting length and quantity, too program. - Semi-au ...
: 36/72 m/min : 285 mm dimensions of saw-band: 2950 x 27 x 0,9 mm capacity 90 degrees: round: 250 mm capacity 90 degrees: square: 220 mm capacity 90 degrees: flat: 280x220 mm capacity 60 degrees: round: 120 mm capacity 60 degrees: square: 80 mm capacity 60 degrees: flat: 140x100 mm capacity 45 degrees: round: 230/200 mm capacity 45 degrees: square: 200/170 mm capacity 45 degrees: flat: 220x200/200x140 mm total power requirement: 1,5/1,8 kW Weight: 485 kg Overall size: 1970x1150x1840 mm Semi-automatic function: - Vice closes and engine starts - Saw head lowers for the cut - Engine shuts off - Saw head lifts, vice opens Semiautomatic dynamic system: Manual lowering of the saw blade to the desired Position and cycle start via the manual button. Upper position is saved automatically. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350 x 32 x 2,5 mm : 15/30/45/90 U/min vice: 190 mm capacity 90 degrees: round: 115 mm capacity 90 degrees: square: 95 mm capacity 90 degrees: flat: 180x95 mm : 90 mm : 90 mm : 110 mm : 95 mm : 125x95 mm : 110 mm : 95 mm : 125x95 mm total power requirement: 1,8/2,5 kW weight: 375 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350 mm dimensions of saw-blade: 350 x 32 x 2,5 mm cutting diameter: 115 mm capacity 90 degrees: square: 95 mm capacity 90 degrees: flat: 180 x 95 mm capacity 45 degrees: round: rechts & links 110 mm capacity 45 degrees: square: rechts & links 95 mm capacity 45 degrees: flat: rechts & links 125 x 95 mm capacity 60 degrees: round: 90 mm capacity 60 degrees: square: 80 mm capacity 60 degrees: flat: 90 x 95 mm cutting speed: 15 - 90 m/min total power requirement: 2,5 kW weight of the machine ca.: 400 kg dimensions of the machine ca.: 1000 x 950 x 1800 mm Features: - With miter adjustment 60° left / 45° right - Machine base The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
