라운드 벤딩 머신 (49)

Key data: 3500 mm, 12 mm

셰퍼 SVRM 3500/12 - CNC 4롤 굽힘기 - 롤러 위치 지정 및 디지털 디스플레이를 위한 조이스틱이 장착된 지멘스 CNC 제어 (2006년 갱신) - 제어판을 통한 상부 롤러의 유압 틸팅 - 강도 900 N/mm²의 담질 및 강화 재료로 제작된 롤러 - 건설 연도 1989 기술 데이터 - 최대 판 폭: 3500 mm - 롤러 베일 길이: 3550 mm - 최대 시트 두께 굽힘: 12 mm - 최대 시트 두께 굽힘 4xS/3xS: 8 / 6 mm - 20% 작업 경화에서 시트의 최대 삽입 한계: 380 N/mm² - 상하 롤러 직경: 360 mm - 측면 롤러 직경: 290 mm - 달성 가능한 최소 반경: 220 mm - 하부 롤러 급여 속도: 200 mm/min - 피드 속도 사이드 롤러: 700 mm/min - 총 설치 용량: 22 kW - 일렉터. 제어: 380 V / 50 Hz / 3 pH - 바닥 아래: 900 mm - 기계 중량: 21100 kg

max. Sheet width: 1000mm Auction-ID: A7-46619-253

제안 26018 기술 데이터: - 최대 작업 거리: 500mm - 최대 시트 두께 1.5mm - 다양한 롤러 직경 - 구동 – 브레이크 모터 400V / 1.4 kW - 공간 요구량 대략 W 850 x D 1700 x H 1250 mm - 대략 무게 0.8 t - 롤러 부착물 42 ; 45 ; 50 ; 55 ; 60 ; 65 ; 70 ; 90 ; 135mm

Auction-ID: A1-46480-2193

Key data: 1020 mm, 1 mm

3롤 원형 굽힘 기계, 와이어 인서트, 솔기 홈 포함, 기계는 전문가가 수리, 점검, 청소를 거쳐 완전히 정상 작동합니다. 시험 운전이 진행됩니다. 작동 길이: 1020 mm 최대 강철 판 두께: 1.25 mm 색상: 초록색 무게: 220 kg 크기: 1290 x 600 x 1050 mm 원형 롤러 수: 3개 롤러 직경: 55 mm 기계 번호 1685

sheet width: 4000 mmplate thickness: 30 / 35 mmpre-bending: 30 mmdiameter of upper rolls: 570 mmside roll diameter: 450 mmdiameter of lower rolls: 540 mmbending speed: 4 m/minmin. bending diameter: 650 mmtotal power requirement: 60 kWweight of the machine ca.: 52 todimensions of the machine ca.: - mThe machine was overhauled in 2022Equipment:- Hydraulic 4-roller round bending machine- Roll material: 61 MnCrMo 43- Driven rolls: 2 Top-and bottom roll-- Drive: over 2 hydro motors direct flanged-- Adjustment speed bottom roll: 0-200 mm/min-- Adjustment speed side rolls: 0-700 mm/min- Speed compensation between top-and bottom roll: automatic- Operation of the tilting bearing: hydraulic- Tilting of the top roll: hydraulic- Bearing block: hydraulic- Indicator device of roll position: digitalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2540 mm, 8 mm

최대 굽힘 길이: 2540 mm 최대 판 두께: 8 mm 강철 상단 롤러 직경: 200 mm 풋스위치를 통한 시계 방향 및 반시계 방향 회전 안전 로프 호이스트 원뿔형 탄환 사용 가능 모터 구동 후방 롤 인피드 위치 표시기가 있는 핸드휠을 통한 하부 롤 공급 무게: 약 4,500 kg

sheet width: 3100 mmplate thickness: 6.0 mm STpre-bending: 4.0 mm STdiameter of upper rolls: 200 mmside roll diameter: 165 mmdiameter of lower rolls: 190 mmbending speed: ca. 5.0 m/minControl: DIGI oil volume: 80.0 Litervoltage: 380 Vtotal power requirement: 6.0 kWweight: 6000 kgrange L-W-H: 5250 x 1500 x 1400 mm very good condition () Current new price approx. 80,000 euros Special price on requestFeatures:- Robust electro-hydraulic 4-roll bending machine 4-roll concept offers a wide range of bending and rounding options- MG swivel control panel Operation - control of all rolls and machine axes Digital position display Manual operation via joysticks- Two central rolls are driven directly by hydraulic motors- Conical rolling possible via inclined position of the rolls- Parallelism of the side rollers via torsion shafts- Bending on both sides- Diameters of up to 1.1 times the upper roller ...

Inv. Num. : 8806 유형: XZMP 3150/16 제작자: 피에속 제작: 1982년 매개 변수: 작동 길이 롤러: 3150mm 최대 시트 두께: 16mm 구동 롤러 수: 3개 무게: 40000kg

Bending length: 4200 mmpre-bending: 34 mmBending strength: 38 mmpower capacity: kWNumber of rollers: 4 StkAdjustable rollers: Stkdiameter of upper rolls: 540 mmdiameter of lower rolls: 500 mmside roll diameter: 365 mmwork speed: 0 - 8 m/mintotal power requirement: 55 kWweight of the machine ca.: 35 tControl: Haeusler Bendtronic 2.0 dimensions of the machine ca.: 7.5 x 2.1 x 2.4 mEquipped with:- Haeusler BENDtronic 2.0 control system- Smallest possible bending diameter with upper roller Ø540mm: 595mm (depending onspringback)- Roller bearings: Self-adjusting roller bearings- Max. cylinder force against upper roller: 3,245kN- Roller material: 42CrMo4 (1.7225)- Speed compensation between upper and lower roller: automatic whenthe two-roller drive option is selected- Roller adjustment: hydraulic- Tilting of the lower roller and both side rollers for cone bending: infinitely variable from th ...

Inv. Num. : 8711 유형: MG 2000 x 25/20 생산자: 마크포트 제작: 1998년, GO 2016 매개 변수: 작동 길이 롤러: 2000mm 최대 시트 두께: 25mm

sheet width: 2600 mmplate thickness: 10,0 mmpre-bending: 8,0 mmdiameter of upper rolls: 230 mmside roll diameter: 190 mmdiameter of lower rolls: 210 mmtotal power requirement: 7,5 kWweight of the machine ca.: 5.560 kg.range L-W-H: 4.650x1.380x1.300 mmFurnishing:- electro-hydraulic 4-roller bending machine- 2x driven main rollers (upper & lower roller)- with hydraulic conical bending device- Induction hardened rollers- including straightening function for welded pipes- Control unit / display with touch screen function digital position display for the two side rollers- mobile control panel- 2x bending speeds selectable- hydraulic folding bearing- Safety device (safety line with switch unit)- Pressure gauge / pressure indicator for the rollers- CE mark + declaration of conformity- Operation manualThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

이 제안은 § 14 BGB의 의미 내에서 기업가만을 대상으로 합니다. 가격은 순 가격에 19% VAT를 더한 가격입니다. 제조사: LECHNER Maschinenbau e.K. 유형: 3100/110 제작 연도: 2020 전압: 400V 소비 전력: 1.5kW 전원 연결: 3상, 제로, PE 상부 롤러 직경: 60 – 100mm 최대 작동 길이: 1100mm 공칭 용량: 3.2mm(시트 두께) 피드 : 5m / min 모든 정보는 오류를 제외하고 우리가 아는 한 제공됩니다. 판매에는 보증이 제외됩니다. 이 예외는 판매자의 중과실 또는 고의적 의무 위반 또는 생명, 사지 및 건강에 대한 상해로 인해 발생하는 손해 배상 청구에는 적용되지 않습니다. 추가 법률 정보는 Witzenmann GmbH 웹사이트에서 "각인", "이용 약관" 및 "데이터 보호"라는 키워드로 확인할 수 있습니다.

sheet width: 3100 mmplate thickness: 13,0 mmpre-bending: 10,0 mmdiameter of upper rolls: 300 mmside roll diameter: 210 mmdiameter of lower rolls: 270 mmtotal power requirement: 11,0 kWFurnishing:- electro-hydraulic 4-roller bending machine- 2x driven main rollers (upper & lower roller)- with hydraulic conical bending device- Induction hardened rollers- including straightening function for welded pipes- Control unit / display with touch screen function digital position display for the two side rollers- mobile control panel- 2x bending speeds selectable- hydraulic folding bearing- Safety device (safety line with switch unit)- Pressure gauge / pressure indicator for the rollers- CE mark + declaration of conformity- Operation manualThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2040 mm, 1 mm

상부 샤프트의 리베이트 홈으로, 스틸 휠과 스케일, 견고하고 안정적인 구조, 와이어 인서트, 후면 롤러의 70mm 공급, 기계는 전문가에 의해 수리, 점검, 청소된 다음 완전히 작동합니다. 시운전이 수행됩니다. 시트 폭: 2040 mm 시트 두께: 1.0 mm 색상: 녹색 기계 무게: 600kg 크기 : 2200 x 650 mm 직경:. 70의 mm 기계 번호: 8413105

sheet width: 3100 mmplate thickness: 50 mmpre-bending: 40 mmtotal power requirement: kWweight of the machine ca.: 40 tdimensions of the machine ca.: 6,7 x 3,0 x 3,0 m4-ROLL Hydraulic Plate Rolling MachineWorking length 3100 mmMaximum thickness Pre-bending 40 mmBending 50 mmYield Point: 240 N/mm2Number of rolls 4Motor Power 55 kWMin. diameter mm - Ø Top Roll Diameter x 3Top roll Ø 540 mmBottom roll Ø 510 mmSide roll Ø 440 mmLength 6700 mmHeight 3000 mmWidth 3000 mmWeight 40.000 kgWith:Cone bending deviceInduction hardened rollsDigital readout for side rollsFully welded steel (St-52) frameSeparate moveable control panelDual bending speedsElectronic ParallelismAll rolls are mounted in spherical roller bearingsHydraulically opened/closed drop end controlled from control panelActivation of cone rolling function and position adjustment via buttons onthe control panelCentral rolls ...

Key data: 1000 mm, 1 mm

리베이트 홈과 와이어 삽입 홈이 있습니다 기계는 전문가에 의해 수리, 점검, 청소된 다음 완전히 작동합니다. 시운전이 수행됩니다. 장 폭: 1000 mm 시트 두께: 1.0 mm . 색상: 블루 기계 무게: 45kg 공간 요구 사항: 1200 x 400 x 1000mm 샤프트 직경: 50mm

플레이트 길이: 1550 mm플레이트 두께: 3,5 mm롤 수 : 3 롤 직경 : 120 mm총 전력 요구 사항 : 2,2 kW기계의 무게 ca.: 750 Kg기계 ca.의 치수: 2,2 x 1,5 x 1,6 m발 레버를 통해 전기로 운영한 둥근 롤러, 건장한, 용접된 건축 대, 원뿔 구부리기를 위해 조정가능한 후방 롤러, 롤러가 굳어지고,상단 롤러를 회전하여 공작물을 제거할 수 있습니다.

최대 굽힘 길이: 2000mm 최대 시트 두께: 8mm 스틸 시계 방향 및 시계 반대 방향 회전 전동식 후방 롤러 인피드 안전 킬 스위치 원뿔형 라운드 가능

시트 폭: 3000 mm 시트 두께: 50 mm 벤딩: 총 전력 요구 사항: kW 기계 중량 약: t공간 요구 사항 약: m4롤 라운드 벤딩 머신: 건설 연도: 1986작업 폭: 3000cm600 mm 롤러에서 가장 작은 파이프 직경: 720 mm 360 mm 롤에서 가장 작은 파이프 직경: 460 mm 시트 두께(재료에 따라 다름): 50 mm 재질 SA- 738 B 작업 폭: 2500 mm재질 SA- 738 B 재질 두께: 35mm이 광고의 데이터는 LogoTech oHG의 기계 관리 인 ModulMWS로 작성되었습니다.

사양: - 손으로 구부리고 구르고, 작업 폭 1020 mm - 물자 간격 St 40 1.25 mm - 엔드 스톱을 통한 벤딩 각도 조정 10 - 180 - 최대 허브 Oberwange 약. 85 밀리미터 - 조정 가능한 굽힘 뺨 20 mm - 샤프트 직경 55 mm - 고조파는 회전 할 수 있습니다. - 후방 샤프트 평행 + 대각선 조정 가능 - 대략적인 공간 요구 사항. W 1500 x H 1400 x D 750 mm - 대략 무게. 400 킬로그�

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 11 kWweight of the machine ca.: 4,450 tdimensions of the machine ca.: 3830 x 1160 x 1180 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

구부리는 길이: 1070 mm 굽힘 수용량: 3.0 mm 롤러: 95 mm 롤러 속도: 9 분당 회전수 모터 출력: 1.1 kW 무게: 370 kg 크기 : 1350 x 760 x 1250 mm

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 24mm total power requirement: 45+22 kWweight of the machine ca.: 43 tdimensions of the machine ca.: 6684 x 2280 x 2375mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

롤 길이: 1250 mm 최대 시트 두께: 1.25 mm 롤 직경: 60 mm 길이: 1780 mm 깊이: 550 mm 높이: 1030 mm 무게: 약 230 kg 가격은 그물, 플러스 부가가치세, 무료 주택 1 주소 독일 (섬없이).

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 25mm total power requirement: 37 kWweight of the machine ca.: 20,5 tdimensions of the machine ca.: 5560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 35mm total power requirement: 45+22 kWweight of the machine ca.: 35 tdimensions of the machine ca.: 5684 x 2280 x 2375mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 40mm total power requirement: 2x37+30 kWweight of the machine ca.: 45 tdimensions of the machine ca.: 6085 x 2630 x 2787mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 50mm total power requirement: 45+45 kWweight of the machine ca.: 72 tdimensions of the machine ca.: 6370 x 3240 x 3660mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 16mm total power requirement: 22 kWweight of the machine ca.: 16,65 tdimensions of the machine ca.: 5560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 10mm total power requirement: 15 kWweight of the machine ca.: 10,6 tdimensions of the machine ca.: 5310 x 1660 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 25mm total power requirement: 30 kWweight of the machine ca.: 15,15 tdimensions of the machine ca.: 5010 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 13 total power requirement: 15 kWweight of the machine ca.: 8,84 tdimensions of the machine ca.: 4760 x 1660 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 4mm total power requirement: 5,5 kWweight of the machine ca.: 2920 tdimensions of the machine ca.: 3600 x 970 x 1140mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 25mm (s) total power requirement: 30 kWweight of the machine ca.: 13950kg tdimensions of the machine ca.: 4510 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 16mm total power requirement: 18,5 kWweight of the machine ca.: 9,6 tdimensions of the machine ca.: 4760 x 1660 x 1140mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 20mm total power requirement: 30 kWweight of the machine ca.: 18,3 tdimensions of the machine ca.: 5560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 20mm total power requirement: 37+22 kWweight of the machine ca.: 39 tdimensions of the machine ca.: 6684 x 2280 x 2375mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 6mm total power requirement: 11 kWweight of the machine ca.: 5,8 tdimensions of the machine ca.: 4880 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 8mm total power requirement: 15 kWweight of the machine ca.: 14,1 tdimensions of the machine ca.: 6310 x 1660 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 13mm total power requirement: 22 kWweight of the machine ca.: 21,3 tdimensions of the machine ca.: 6560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 11 kWweight of the machine ca.: 4,570 tdimensions of the machine ca.: 3830 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 15 kWweight of the machine ca.: 8 tdimensions of the machine ca.: 4260 x 1160 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 30mm (S) total power requirement: 37 kWweight of the machine ca.: 15,3 tdimensions of the machine ca.: 4510 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 16 total power requirement: 37 kWweight of the machine ca.: 23,81 tdimensions of the machine ca.: 6560 x 2060 x 2050mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 6 total power requirement: 7,5 kWweight of the machine ca.: 4,340 tdimensions of the machine ca.: 3830 x 1160 x 1180mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: 8mm total power requirement: 15 kWweight of the machine ca.: 9,7 tdimensions of the machine ca.: 5310 x 1660 x 1590 mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD total power requirement: 18,5 kWweight of the machine ca.: 8,5 tdimensions of the machine ca.: 4260 x 1660 x 1590mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mmplate thickness: siehe TD mmpre-bending: siehe TD 0: 20mm (s) Ampullen/h0: mm0: mmtotal power requirement: 22 kWweight of the machine ca.: 9,2 tdimensions of the machine ca.: 4260 x 1660 x 1590 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.