We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
utilisé
Cave Soufflantes d’extraction 1.8kW
utilisé
Keller SMM 016,0 Soufflantes d’extraction Diamètre 160/160mm Débit d’air 1200 Nm³/h 1,5 kW
utilisé
Cave SMM 012.0 Soufflantes d’extraction Diamètre 120/120mm Débit d’air 700 Nm³/h 0.55kW
utilisé
Débit volumique 2 000 – 3 000 m³/h Niveau de pression acoustique < 75 dB L/W/H 1,4 m / 1,4 m / 2,0 m Poids 1 025 t Puissance requise 7,5 kW
utilisé
Description: Machine number: 502485 Operating voltage: 400 V Frequency: 50 Hz Connection: 5.5 kW Approx. Onsite Dimension. (l x w x h): 1,400 x 1,200 x 2,000 mm, weight approx.: 500 kg
utilisé
Two-roll corrugating machine - crimper, for the production of polyester staple fibers, manufactured by KELLER (USA) by order of KOBE STEEL (Japan). The width of the work rolls is 150 mm. It is equipped with a clamping pneumatic cylinder and a drive gearbox manufactured by SEISA REDUCTION GEARS with a capacity of 150 kW. Productivity is up to 50 tons / hour. Made of AISI 304 stainless steel. 4 pieces are available. The equipment was practically not used - an operating time of about 60 hours.
utilisé
Single screw degassing extruder CFE-699-A-04 for polymers manufactured by KELLER (USA) and KOBE STEEL (Japan) under a DUPONT license. The extruder has the following parameters: Overall dimensions of the extruder, taking into account the gearbox and motor - length 12 meters, width -2.5 meters, height -1.5 meters, the total diameter of the casing with a heating-cooling jacket is 950 mm, the diameter of the screw is 600 mm, screw length -7800 mm. The average screw speed is 22-25 rpm. The total weight of the extruder without spare parts is 40 tons. The working pressure in the casing is up to 300 bar, the working temperature of heating the melt is up to 300 degrees. The casing of the extruder is heated by high temperature oil supplied to it. The average productivity of polymers is 50-100 tons per hour. The extruder is equipped with a parallel reducer of POWER-TECH INTERNATIONAL (FOOT-JONES) ...
utilisé
Type: Vario T 1.0 L originates from LVD lasercutting machine power: 2,2 kW
utilisé
Données techniquesDévitesse de rotation : 1800 tr/minAssiner aspiré : 20 m3/minTension 50 Hz 3x : 400 VoltMoteur de conduite (puissance du moteur ) : 1,1 kWPuissance : 2,7 Poids : 100 kgDimensions : Longueur : 800 mmLargeur : 550 mmHauteur : 1100 mm
utilisé
Capacité (x): 0 Application de traitement: 0 Autres informations: 0 Données techniques Décision de broche: 2850 tr/min Asservent aspiré: 1000 m3/h Tension 50 Hz 3x: 400 Volt Moteur de conduite (puissance du moteur): 1,5 kW Dimensions: Détenance: 1200 mm Largeur: 800 mm Hauteur: 2300 mm
utilisé
Capacité (x): 0 Process Application: 0 Autres infos: 0 Données techniques Tension 50 Hz 3x: 400 Volt Puissance installée: 0.55 kW Poids: 60 kg Dimensions: Détendance: 650 mm Largeur: 500 mm Hauteur: 1100 mm
utilisé
sheet width: 480 mm plate thickness: 3 mm stations: 13 total power requirement: kW weight of the machine ca.: 11 t dimensions of the machine ca.: 15,x2 m Number of stations 13 Number of straightening stations 1 Waves 60 mm Center distance, horizontal 310 mm Center distance, vertical 110 - 250 mm Speed approx. 11 m / min. Connected load approx. 20 kW Uncoiler (without drive) - Coil- , inside 508/610 mm - Coil weight 3 t Flying hydraulic scissors Roller set for hat profile The techn. Data is manufacturer or operator information and therefore for us not binding. We reserve the right to make an interim sale, it applies exclusively our business and conditions of sale. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.