CONTROLS electronic controls PRESS DESIGN drive system: hydraulic frame design: C-frame, single sided number of suspensions: 1 number of slide actions: 1 PRESS FORCES total force (nominal): 25 toPRESS TABLE table surface (left-right): 645 mm table surface (front-back): 535 mmSLIDE slide force: 25 to table surface (left-right): 500 mm table surface (front-back): 430 mm stroke: 400 mmSLIDE (HYDR. PRESS) return force: 4 toTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 500 mmSTRIP-FEEDER feeder type: grip feeder sheet width max.: 76 mm sheet thickness max.: 3 mmELECTRICAL SPECIFICATIONS total power consumption: 7.5 kW mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS total weight approx.: 4000 kgMachine in like-new condition (lightly used)Optional with conveyor system and gripper feed:
CONTROLS electronic controls PRESS DESIGN drive system: hydraulic frame design: 4 column number of suspensions: 1 slide ejectors / cushion: yes table cushion: yes PRESS FORCES total force (nominal): 200 toPRESS TABLE table surface (left-right): 1330 mm table surface (front-back): 1150 mm height above floor level: 850 mm opening in bed (diameter): 250 mmSLIDE slide force: 200 to table surface (left-right): 1200 mm table surface (front-back): 1200 mm stroke: 800 mmSLIDE (HYDR. PRESS) approximation velocity max.: 300 mm/s working velocity min.: 30 mm/s return velocity max.: 400 mm/s return force: 200 toSLIDE EJECTOR / CUSHION working principle: hydraulical nominal force: 30 to stroke: 130 mmDIE CUSHION (TABLE CUSHION) cushion force: 30 to stroke: 850 mmELECTRICAL SPECIFICATIONS mains voltage: 400 V mains freq ...
压力 总力（名义）：1000 到 工作台 工作台表面（左右）1800 毫米 桌面（前后）1300 毫米 滑动行程：500 毫
CONTROLS PLC SIEMENS SIMATIC OP 27 PRESS DESIGN table cushion: yes PRESS FORCES total force (nominal): 300 toPRESS TABLE table surface (left-right): 1800 mm table surface (front-back): 1000 mmSLIDE stroke: 600 mmSLIDE (HYDR. PRESS) return force: 38 toDIE CUSHION (TABLE CUSHION) stroke: 200 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS total weight approx.: 43000 kgEl. cabinet (Ritta)Machine hours: 46131
CONTROLS PLC SIEMENS SIMATIC OP 27 PRESS DESIGN table cushion: yes PRESS FORCES total force (nominal): 300 toPRESS TABLE table surface (left-right): 1800 mm table surface (front-back): 1000 mmSLIDE stroke: 600 mmSLIDE (HYDR. PRESS) return force: 38 toDIE CUSHION (TABLE CUSHION) stroke: 200 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS total weight approx.: 43000 kgEl. cabinet (Ritta)Machine hours: 32510
CONTROLS PLC SIEMENS SIMATIC OP 27 PRESS DESIGN table cushion: yes PRESS FORCES total force (nominal): 300 toPRESS TABLE table surface (left-right): 1800 mm table surface (front-back): 1000 mmSLIDE stroke: 600 mmSLIDE (HYDR. PRESS) return force: 38 toSLIDE EJECTOR / CUSHION stroke: 200 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS total weight approx.: 43000 kgEl. cabinet (Ritta)Machine hours: 47037
控制 PLC 西门子SIMATIC面板冲压设计 桌面靠垫：是的 压力 总力（名义）：400 到 压 工作台 工作台表面（左右）：2000毫米 前后操作面：1300毫米 滑动行程：700毫米 模具缓冲（桌面缓冲） 行程：200毫米 刀具组件尺寸 关闭高度（行程向下，调节向上），BDC：1100毫米 机械工时：14060
控制 传统压力 总力（名义）：160 至 工作台 工作台表面（左右）：1000 毫米 前后工作台面：850毫米 滑动行程：705毫米 刀具组装尺寸 关闭高度（行程向下，调整上方），BDC：1205毫米 机时数：78571
LOIRE SAFE Hydraulic Press – High-Performance System for Tooling and Heavy Forming ApplicationsThis high-performance hydraulic press, designed in a rigid 4-column portal frame construction, is ideally suited for demanding applications in toolmaking (tryout / spotting) as well as large-scale forming operations. The stress-relieved welded structure ensures maximum rigidity and long-term process stability.The machine is equipped with three main cylinders and a multi-cylinder parallel control system, achieving high repeatability in the range of ±0.1 mm. The powerful hydraulic system, based on Bosch Rexroth components, operates at a maximum working pressure of approx. 450 bar, delivering both precision and high pressing force.Control is handled via a Siemens S7-317F PLC combined with servo-controlled axes (Rexroth MLC) and visualization through Siemens WinCC. This setup enables fully progr ...
压力：150 T行程：毫米 桌子/RAM间距离：660毫米 桌面表面积：1500 x 610毫米 桌面与地面高度：毫米 密封直径：150毫米 长度 L-W-H：1.7 x 1.5 x 2.3 m 机器重量 约：tC-框架-压孔 - 桌子上的孔 120 毫米本广告数据使用 ModulMWS——LogoTech oHG 的软件解决方案
PRESS DESIGN drive system: hydraulic frame design: C-frame, single sided table cushion: yes opening in table: yes PRESS FORCES total force (nominal): 100 toPRESS TABLE table surface (left-right): 710 mm table surface (front-back): 560 mmSLIDE slide force: 100 to table surface (left-right): 560 mm table surface (front-back): 450 mm spigot hole diameter: 50 mm stroke: 320 mm thickness of bolster plate: 150 mmSLIDE (HYDR. PRESS) approximation velocity max.: 340 mm/s working velocity max.: 32 mm/s return velocity max.: 330 mm/sSLIDE EJECTOR / CUSHION nominal force: 2 to stroke: 40 mmDIE CUSHION (TABLE CUSHION) cushion force: 10 to stroke: 80 mmTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 455 mmSTRIP-FEEDER feeder type: roll feeder sheet width max.: 300 mm sheet thickness max.: 20 mm spee ...
CONTROLS PLC SIEMENS S5 95U PRESS DESIGN drive system: hydraulic openings in uprights: yes PRESS FORCES total force (nominal): 350 toPRESS TABLE table surface (left-right): 1600 mm table surface (front-back): 1400 mmSLIDE stroke: 1200 mmSLIDE (HYDR. PRESS) approximation velocity max.: 250 mm/s working velocity min.: 14 mm/s working velocity max.: 50 mm/sTOOL ASSEMBLY DIMENSIONS distance table - slide max.: 1250 mm distance between columns (H-frame): 1650 mm passline opening (free passage in side columns): 630 mmELECTRICAL SPECIFICATIONS total power consumption: 60 kWDIMENSIONS / WEIGHTS height above floor level: 4300 mm height under floor level: 1000 mm total weight approx.: 24000 kgATTACHMENTS (PRESSES) European CE standards: yes
CONTROLS PLC SIEMENS S5 95U PRESS DESIGN drive system: hydraulic frame design: H-frame, monoblock openings in uprights: yes number of suspensions: 2 table cushion: yes PRESS FORCES total force (nominal): 650 toPRESS TABLE table surface (left-right): 3000 mm table surface (front-back): 1800 mmSLIDE slide force: 630 to table surface (left-right): 3000 mm table surface (front-back): 1800 mm stroke: 1000 mmSLIDE (HYDR. PRESS) approximation velocity max.: 200 mm/s working velocity min.: 7 mm/s working velocity max.: 15 mm/s return velocity max.: 120 mm/s return force: 65 toDIE CUSHION (TABLE CUSHION) cushion force: 250 to stroke: 400 mm cushion plate surface (left-right): 2500 mm cushion plate surface (front-back): 1450 mm working principle: hydraulical TOOL ASSEMBLY DIMENSIONS distance table - slide max.: 1250 mm ...
压力：630 t直径：320 mm行程：310 mm总功率要求：kW机器重量约：3500 t机器尺寸约：m此广告的数据是使用 ModulMWS 创建的 - LogoTech oHG 的软件解决方案
CONTROLS PLC SIEMENS S7 300 PRESS DESIGN drive system: hydraulic PRESS FORCES total force (nominal): 800 toPRESS TABLE table surface (left-right): 2600 mm table surface (front-back): 2000 mm height above floor level: 540 mmSLIDE stroke: 900 mmSLIDE (HYDR. PRESS) approximation velocity max.: 460 mm/s working velocity min.: 25 mm/s working velocity max.: 44 mm/s return velocity max.: 460 mm/sTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 1700 mmELECTRICAL SPECIFICATIONS total power consumption: 180 kWDIMENSIONS / WEIGHTS total weight approx.: 95000 kgATTACHMENTS (PRESSES) press automation: yes gripper transfer system: yes acc. to actual accident protection regulation: yes European CE standards: yes Complete hot forming line consisting of: Hydraulic press NEFF 800 to. Ruhstrat furnace system:- Natural gas heat ...
压力机设计 驱动系统：液压 框架设 ：C型框架，单面压力 总力（标称）：12至 动 行程：200毫米电气规格 电源电压 ：380 V 电源频率：50赫兹尺寸/重量总 重量 约：1000公斤小时计数器：30'181 hlast安全检查： 27.07.2023，超限时间 38 毫秒，超限距离 60 毫
压力：63 t支架宽度：0 mm行程：160 mm工作台面：630 x 500 mm安装高度：400 mm总功率要求：kW机器重量约：5 t空间要求约：m本广告的数据是使用ModulMWS创建的 - LogoTech oHG的机器管理
锁模力：4360 kN工作台尺寸：730 x 730 mm控制：B+R 工业电子 缩回力：190 kN进给速度：最大 60 mm/秒 缩回速度：最大 90 mm/秒机架之间的净宽：900 mm= 硫化机，带垂直夹紧装置和脱模装置的数据 ü，本广告是使用 ModulMWS 创建的 - LogoTech 的机器管理呵呵
