子类目
(三级类目)
生产厂家:
(品类: 301)
Hypet400HPP P100/120 E140 + 96腔赫斯基模具+百旺助剂 2010年 预计交付2023年7月 可以在生产中检查和查
Hypet400HPP P100/120 E140 + 96腔赫斯基模具+塑料系统助剂 2008年 预计交付2023年7月 可以在生产中检查和查看
赫斯基HPETL230E-RSE95D-95 + 48 腔式热流道 + 辅助式冷水机组 2015年12月 模具：包括（哈士奇）注意没有冷的一半包括在内 循环时间 ： 9 秒 包括配件 1.除湿干燥机 2.冷水机 3.料斗 4.机器人 5.防结露装置 快速交货 位于亚洲 频率为 50 和 60HZ
两周清算 赫斯基 HYPET AE 230 RSE 80D/80 + 模具 + 辅助公司冷水机组 2013年10月 模具：14克x 48（30毫米水颈）腔（赫斯基） 循环时间 ： 9 秒 包括配件 1.除湿干燥机 2.冷水机 3.料斗 4.机器人 5.防结露装置 最快的交货 必须去 索取视频 不会持续 位于亚洲 频率为 50 和 60HZ
住友德马格 系统科技 SP 280/630-840 制造年份 2014 280 吨 夹具 2800kn 拉杆区 630 注射单元 840 德国施韦格制造 400v 50赫兹 南美
2016 赫斯基PET瓶坯模具; 项目ID xxxxxx; 型号 96-50x120-HPP5.1; 34毫米行程; PV 14.6gr / 最大 96 腔 （96-50x120-HPPS-1） 最大电容231t / rec. 瓶盖201吨; 仪表读数 286.747; 带热流道系统; 冷半PCO 1881（51，594次循环aprox）20克瓶坯; 安装在赫斯基机器上的模
BMB高吨位注塑机 1000 吨 型号 KW 1000 / 7500 制造年份 2000 电压 400 频率 50hz 可用性，随时可以加载 请看图
内格里博西 - 萨克米 1300吨高吨注塑机 制造年份 2014 双电源 VH1300 型号 /12100 120mm 螺丝 计算注射体积 7351 cm3 注射重量 6689 克 HxV 拉杆之间的间距 1400 x 1200 状况良好，可在生产中检查和查
海佩特500出售 我们只出售带模具的机器 144腔完整模具 29/25 颈部完成 瓶坯重量 10.63 克由赫斯基制造 本机HPP 4.0和国际空间站，速度快。 循环 6.2 （每小时 83612 个预制棒） 每天 200 万份瓶坯 2011 年制造 安装于 2012 年 380v 50hz 良好条
赫斯基GL300系统48mm +3025 +食用油32mm + 2921模具机会 赫斯基GL300 1998年 模具 + 48mm水颈完成32腔完整模具（热流道），2套芯（81gr~85gr ~91gr） + 30/25水颈完成48腔完整模具（热流道），带1个芯组（16 〜18.2克） + 32mm 食用油 （卡扣式）（宽食用油） 颈部完成冷半模与芯集 （24~27gr.） + 29/21 食用油 25 gr 颈部完成瓶坯更换套件。 辅助设备：Piovan模具除湿机、带料斗的树脂干燥机、 T型输送机 400v 50赫兹 条件：正常条件，连接（可检查） 更多图片可根据要求 美国专线： +1 305 831 8888 什么应用 +5491157143569 j.plaul@optimisense
这把Kloeckner Desma PU D522/12-LDI于2017年制造。设计用于PU注入和热靴生产， 用12站位装置，夹持力为70千牛。它配备了反应式注 单元、自动模具滑块和23.16千瓦的电机容量。供暖能 为45.50千瓦。如需了解更多关于这台机器的信息，请 联系我们
For sale is an ENGEL Victory 330/80 Tech tie-bar-less injection moulding machine including 3-axis handling and conveyor belt. The machine was in ongoing production use until the CPU/controller failed and worked smoothly until then. Currently, the machine is not ready for operation due to a defect in the controller. The installed KEBA Kemro K2-200 CP 251/Z PLC/CPU controller is currently not booting and displays error message 8. Repair services and replacement devices are offered on the market for this CPU type. We did not carry out any further fault diagnosis or repair. Technical data / equipment: Manufacturer: ENGEL Model: Victory 330/80 Tech Year of Make: 2007 Tie-bar-less design Clamping force: 800 kN / 80 t Injection volume: 154 cm³ Injection pressure: 1,600 bar Mold opening stroke: 456 mm Ejector stroke: 100 mm Machine weight: approx. 5,300 kg 3-axis removal handling incl ...
Injection Unit Screw Diameter: Ø 50 Injection Volume: approx. 490 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 350 cm³/s Plasticizing Capacity: approx. 50 g/s (PS) Nozzle Contact Force: 65 kN Clamping Unit Clamping Force: 2,600 kN (260 t) Clamping System: ENGEL Victory tie-bar-less design Platen Size (H × V): approx. 1,000 × 950 mm Mould Opening Stroke: 600 mm Max. Daylight Opening: approx. 950 mm Min. Mould Height: 350 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 50 / 30 kN Drive & Control Drive Type: Hydraulic Hydraulic System Pressure: up to 160 bar Pump Motor Power: 22 kW Total Installed Power: approx. 30 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping Concept: Tie-bar-less design for improved mould accessibility and compact footprint Hydraulics: Energy-saving hydraulic ...
Injection Unit Screw Diameter: Ø 70 Injection Volume: approx. 1,540 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 500 cm³/s Plasticizing Capacity: approx. 95 g/s (PS) Nozzle Contact Force: 120 kN Clamping Unit Clamping Force: 6,500 kN (650 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,600 × 1,500 mm Mould Opening Stroke: 900 mm Max. Daylight Opening: approx. 1,600 mm Min. Mould Height: 450 mm Ejector Stroke: 250 mm Ejector Force (fwd / back): 110 / 70 kN Drive & Control Drive Type: Servo-hydraulic (ecodrive inside) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 45 kW Total Installed Power: approx. 65 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping System: Two-platen design for compact footprint and high stability Energy Efficiency: Servo-hy ...
Machine type: Injection moulding machine Manufacturer: ENGEL Model: Duo 3550/400 Pico Year of manufacture: 2013 Serial number: 191000 Clamping force: 400 t Clamping system: Two-platen Hydraulic system pressure: up to 160 bar Drive system: Servo-hydraulic ecodrive inside” Pump motor power: 30 kW Total installed power: approx. 45 kW Power supply: 400 V / 50 Hz / 3-phase Control system: ENGEL CC300 control unit Control features: Colour touchscreen, integrated process monitoring Equipment / Features: - Automatic central lubrication system - Safety interlocks on operator and service sides - Energy-efficient servo-hydraulic drive - Designed for large technical and automotive moulding applications Overall dimensions (L x W x H): approx. 6800 x 1900 x 2400 mm Own mass: approx. 11,000 kg Auction-ID: A7-49839-1
Injection Unit Screw Diameter: Ø 65 Injection Volume: approx. 1,075 cm³ Injection Pressure: up to 1,750 bar Injection Rate: approx. 400 cm³/s Plasticizing Capacity: approx. 85 g/s (PS) Nozzle Contact Force: 110 kN Clamping Unit Clamping Force: 5,500 kN (550 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,350 × 1,300 mm Mould Opening Stroke: 850 mm Max. Daylight Opening: approx. 1,450 mm Min. Mould Height: 400 mm Ejector Stroke: 220 mm Ejector Force (fwd / back): 95 / 65 kN Drive & Control Drive Type: Hydraulic (pre-ecodrive generation) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 45 kW Total Installed Power: approx. 65 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL EC88 digital control panel Equipment / Features Clamping System: Robust two-platen design for high rigidity and precision Platen Area: Large platen ...
Injection Unit Engine not working Screw Diameter: 65 Ø Injection Volume: approx. 1,025 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 450 cm³/s Plasticizing Capacity: approx. 80 g/s (PS) Nozzle Contact Force: 100 kN Clamping Unit Clamping Force: 5,000 kN (500 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,300 × 1,200 mm Mould Opening Stroke: 800 mm Max. Daylight Opening: approx. 1,400 mm Min. Mould Height: 400 mm Ejector Stroke: 200 mm Ejector Force (fwd / back): 90 / 60 kN Drive & Control Drive Type: Servo-hydraulic (ecodrive inside) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 37 kW Total Installed Power: approx. 55 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping System: Two-platen design for high rigidity and space efficiency Energy Efficie ...
Injection Unit Screw Diameter: Ø 55 Injection Volume: approx. 517 cm³ Injection Pressure: up to 2,000 bar Injection Rate: approx. 220 cm³/s Plasticizing Capacity: approx. 35 g/s (PS) Screw L/D Ratio: 22:1 Nozzle Contact Force: 60 kN Clamping Unit Clamping Force: 2,300 kN (230 t) Clamping System: Zhafir Zeres all-electric toggle system Platen Size (H × V): approx. 850 × 800 mm Mould Opening Stroke: 470 mm Max. Daylight Opening: approx. 940 mm Min. Mould Height: 220 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 50 / 30 kN Drive & Control Drive Type: All-electric servo drive Installed Power: 47 kW Full Load Current: 79 A Short Circuit Current: 25 kA Power Supply: 400 V / 50 Hz / 3-phase Control System: Zhafir SIGMATEK HMI touchscreen control Equipment / Features Drive Concept: Fully electric servo system for high precision and energy efficiency Operation: Quiet opera ...
Injection speed 330 mm/s, tie bar spacing 560x510 mm, plate size 800x750 mm, min. mold size 325x300 mm, total heating power 6.5 kW, power source 3-phase AC 200 V at 50/60 Hz, without injection molding tool Auction-ID: A1-49516-2
Injection speed 330 mm/s, tie bar spacing 460x410 mm, plate size 660x610 mm, min. mold size 265x240 mm, total heating power 6.5 kW, power source 3-phase AC 200 V at 50/60 Hz, without injection molding tool Auction-ID: A1-49516-1
Uniloy Milacron UR-110 16 Head Reciprocating Screw Intermittent-Extrusion Blow Molding Machine (2012)Extrusion systemTechnology: Reciprocating screw, intermittent extrusionMaterials: HDPE, PP (with flexibility for others)Output: High-volume monolayer productionApplications: Dairy, edible oils, juices, household chemicalsTypical bottle range: 100 mL to 2 LNumber of heads: 16Container types: Lightweight monolayer bottles, handleware & non-handleware, foil-seal compatible Auction-ID: A1-48805-89
clamping force: 600 kNinjection volume: 106 cm³screw diameter: 30 mmplaten size: 590 x 600 mmCondition: used,Specification: Horizontal injection moulding machine, type: System 60/420-200- Internat. Size specification: 600 - 200injection unit:- Screw diameter: 30 mm- L/D - ratio: 20D- Injection volume: 106 cm³- Injection pressure: 1995 bar- Cylinder heating: 8,3 kWclamping unit:- Clamping force: 600 kN- Max. opening stroke: 450 mm- Mould installation height: min. 250 mm- Max. platen distance: 700 mm- Mould clamping platens: 590 x 600 mm- Clear column distance: 420 x 420 mmTotal machine:- Oil tank filling: 180 ltr.- Pump capacity: 22 kW- Voltage: 3x 400V, 50 Hz- total power: 30,3 kW- Dimensions L/W/H: approx. 4200 x 1400 x 2000 mm- Weight without oil approx ...
clamping force: 600 kNinjection volume: 144 cm³screw diameter: 35 mmplaten size: 570 x 570 mmclosing stroke: 500 mmCondition: usedSpecification: Horizontal injection moulding machineclamping unit:- Clamping force max.: 600 kN- clamping platens: 570 x 570 mm- clear column distance: 370 x 370 mm- Distance between the mould mounting platens: 750 mm- Mould installation height: 250 mm- Opening stroke max.: 500 mm- Ejector travel hyd. Ejector stroke: 175 mm- Ejector force max.: 40 kNInjection unit:- Screw diameter: 35 mm- Screw length: 20D- Screw stroke max.: 150 mm- Max. dosing volume: 144 cm³- Moulded part weight: 121 g- Injection pressure: 1,820 bar- Injection flow max.: 154 cm³/s- Screw peripheral speed: 57 m/min- ...
clamping force: 450 kNinjection volume: 135 cm³screw diameter: 35 mmplaten size: 550 x 430 mmCondition: second-hand,Specification: Horizontal injection moulding machineInjection unit:- Screw diameter: 35 mm- Screw length L/D: 17.3D- Dosing stroke: 140 mm- Screw speed: 20 – 480 rpm- Moulding volume: 135 cm³- Injection pressure: 1,065 bar- Increased injection pressure: 1,620 bar- Heating power: 6.8 kW- Number of heating zones (including nozzle): 4Clamping unit:- Maximum clamping force: 450 kN- Platen dimensions: 550 x 330 mm- Extended clamping plates: 550 x 430 mm- Minimum mould installation height: 180 mm- Maximum plate spacing: 530 mm- Opening stroke: 350 mm- Control system: EC 100Drive:- Pump drive power: 11 kW- Approx. weight: 3,300 kg- ...
clamping force: 4.000 kNinjection volume: 2480 cm³screw diameter: 90 mmplaten size: 1.300 x 1.080 mmCondition: second-hand,Specification: Horizontal injection moulding machine Injection unit:- Screw diameter: 90 mm- Injection volume: 2,480 cm³- Maximum shot weight: 2,232 g- Injection pressure: 1,360 bar- Increased injection pressure: 1,600 bar- Heating capacity: 64 kWClamping unit:- Max. clamping force: 4,000 kN- Clamping plates: 1,300 x 740 mm- Extended clamping plates: 1,300 x 1,080 mm- Minimum mould installation height: 350 mm- Maximum platen spacing: 1,300 mm- Opening stroke: 950 mm- Core pull unit: 2-stage on BAP- Control system: EC 100Drive:- Pump drive power: 55 kW- Weight (clamping side) appr ...
Used SACMI OIMA 350T injection molding machine - Year 2010Technical Specifications & Performance DataThis injection molding machine for PET preforms is a high-output cell engineered for beverage production and industrial packaging applications. Manufactured by OiMA, it combines robust clamping performance with precise injection control and a complete set of auxiliaries for reliable second hand operation within a used bottling line context.Manufacturer: OiMA S.p.A.Model: 6500.350Application: PET preform production for beverage packagingClamping force: 350 tonInjection volume: 4500 cm³ per 100 MPaInstalled power: 436.58 kWPower supply: 400 V, 50 HzMachine mass: 20,000 kgPress year: 2014Mold: SACMI PPM 072 H, 72 cavities, 34 g preforms, neck type Alaska Blue PRE 342Year: 2010Mold temperature: 8–12 °CMold mass: 9,720 kgAuxiliaries included: Sytrama REV 156 PET take-out robot; Plastic Sys ...
100 € 
