sheet width: 2100 mm plate thickness: 8 mm pre-bending: 6 mm upper roll diameter: 190 mm lower roll diameter: 170 mm side roll diameter: 150 mm total power requirement: 3 kW weight of the machine ca.: 3.450 kg Machine dimensions approx.: 4040x1380x1255 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
板材厚度：1.25 mm 滚筒体间距：250 mm 投影：260 mm 滚筒中心距离：62 mm 安装：26 mm 速度：6.3 m/min 总功率要求：0.7 kW 重量：170 kg 尺寸 L-W-H：1020x600x1500 mm 设备： - 电动串珠机 - 5 套渗流辊 - 脚踏开关 - 德国 - CE标志/符合性声明的 操作说明 ! !为您服务机器租赁长达60个月，无需首付，无残值， 个人建议和根据要求计算个人租赁费率。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。
bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
板材厚度：4 mm 滚筒体间距：260 mm 投影：500 mm 滚筒中心距：132 mm 安装：40 mm 速度：5 m/min 总功率要求：2.2+0.55 kW 机器重量约：450 kg 空间要求约：1800x700x1600 mm 设备： - 谐波可通过液压方式打开 和关闭- 3 套渗漏辊 - 脚开关 - 德国 - CE 标志/符合性声明上的 操作说明 ! !为您服务机器租赁长达60个月，无需首付，无残值， 个人建议和根据要求计算个人租赁费率。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。
sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 200 mm min. bending diameter: Ø 300 mm bending speed: 5 m/min total power requirement: 5,5 kW weight of the machine ca.: 4.000 kg dimensions of the machine ca.: 4800x1300x1270 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 4100 mm plate thickness: 35 mm pre-bending: 28 mm upper roll diameter: 540 mm lower roll diameter: 541 mm side roll diameter: 440 mm total power requirement: 37 kW weight of the machine ca.: 48.100 kg Machine dimensions approx.: 7670x3000x2930 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
板材厚度：2.5 mm 滚筒体间距：260 mm 投影：500 mm 滚筒中心距离：92 mm 安装：35 mm 速度：3.5 m/min 总功率要求：1.5 kW 机器重量约：295 kg 空间要求约：1200x700x1200 mm 设备： - 电动串珠机 - 3 套渗流辊 - 脚踏开关 - 德国 - CE 标志/符合性声明 上的操作说明 ! !为您服务机器租赁长达60个月，无需首付，无残值， 个人建议和根据要求计算个人租赁费率。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。
板材厚度：4 mm 辊筒体间距：260 mm 投影：500 mm 卷筒中心距离：132 mm 安装：40 mm 速度：5 m/min 总功率要求：2.2 kW 机器重量约：350 kg 空间要求约：1650x700x1280 mm 设备： - 电动串珠机 - 3 套渗流辊 - 脚踏开关 - 德国 - CE 标志/符合性声明上的 操作说明 ! !为您服务机器租赁长达60个月，无需首付，无残值， 个人建议和根据要求计算个人租赁费率。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。
table diameter: 1300 mm table load: 7.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M24 Tilt Angle: 90-180-100 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 3.050 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 25 mm pre-bending: 20 mm upper roll diameter: 390 mm lower roll diameter: 360 mm side roll diameter: 300 mm total power requirement: 18,5 kW weight of the machine ca.: 17.100 kg Machine dimensions approx.: 5800x2100x2000 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ...
round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
板材宽度：1050 mm 板材厚度：1 mm 卷直径：56 mm 空间要求约：1600 x 700 x 1050 mm 设备： - 顶部滚筒手动旋转 可选设备： - 硬化滚子 ! !为您服务机器租赁长达60个月，无需首付，无残值， 个人建议和根据要求计算个人租赁费率。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。
sheet width: 2100 mm plate thickness: 13 mm pre-bending: 10 mm upper roll diameter: 230 mm lower roll diameter: 210 mm side roll diameter: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4.620 kg dimensions of the machine ca.: 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...
table diameter: 960 mm table load: 3.500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M20 Tilt Angle: 70-90-180 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 1.500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
板材厚度：2.5 mm 滚筒体间距：260 mm 投影：500 mm 卷筒中心距离：92 mm 安装：35 mm 速度：3.5 m/min 总功率要求：1.5+0.55 kW 机器重量约：320 kg 空间要求约：1200x700x1200 mm 设备： - 谐波可液压上下切换 - 3 套珠辊 - 脚开关 - 德语 操作说明- CE 标志/符合性声明 ! !为您服务机器租赁长达60个月，无需首付，无残值， 个人建议和根据要求计算个人租赁费率。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。
table diameter: 715 mm table load: 500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-110 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 675 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 10 mm pre-bending: 8 mm upper roll diameter: 270 mm lower roll diameter: 250 mm side roll diameter: 210 mm total power requirement: 11 kW weight of the machine ca.: 7750 kg Overall size: 5600x1450x1600 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bending speed: 2.1 m/min Bending capacity - square: 30x30 mm bending capacity - flat iron: 80x15 mm Bending capacity - flat iron on edge: 50x10 mm tube diameter: 1 oder 60x2 mm Shaft diameter - upper: 35 mm Shaft diameter - lower: 30 mm total power requirement: 0,75 kw range L-W-H: 650 x 500 x 1300 mm weight: 170 kg Standard features: - hardened special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 900 mm table load: 1.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1,1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-105 ° Tilting Speed: 30 sn min./90° dimensions: 2100x920x1100 mm weight of the machine ca.: 930 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mm plate thickness: 4,5 mm pre-bending: 4,0 mm min. dia.: 210 mm roll diameter: 140 mm weight of the machine ca.: 1530 kg dimensions of the machine ca.: 3220x1200x900 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
：2100毫米：7毫米：6毫米卷径：190毫米。直径：285毫 ：4千瓦：3200公斤：4000x1350x1500毫米。设备：- 电动后滚轮调节 - 数字显示 - 自动锥形弯曲。 - 脚踏开关——安全装置本广告的数据由LogoTech oHG的软件解决方案ModulMWS创建
working length: 2050 mm : 2.0 mm max. wire thickness: 3.0 mm Underfloor: 110 mm motor strength: 165 mm motor strength: 22 kW bending speed: 5.2 mm/min length: 3150 mm height: 1150 mm width: 850 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
