sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 170 mm min. bending diameter: Ø 255 mm bending speed: 4,5 m/min total power requirement: 4 kW weight of the machine ca.: 2300 kg dimensions of the machine ca.: 3800x1100x1130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - upend: 100 x 20 (d 2100) mm tube diameter max.: 100 x 3 (d 3000) mm L-beam: 80 x 80 x 8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm bar material - diameter: 60,0 (d 1000) mm I-beam section - flat steel: 120 x 30 (d 600) max. 140 mm tool taper: 80,0 turning speeds: 4,2 U/min weight: 1600 kg dimensions: 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according ...
sheet width: 3100 mm plate thickness: 6 mm pre-bending: 4 mm upper roll diameter: 210 mm lower roll diameter: 190 mm side roll diameter: 170 mm total power requirement: 7,5 kW Overall size: 5200x1400x1300 mm machine weight ab.: 5.400 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2100 mm plate thickness: 6 mm pre-bending: 4 mm upper roll diameter: 160 mm lower roll diameter: 140 mm side roll diameter: 120 mm total power requirement: 2,2 kW Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll diameter: 90 mm min. dia.: 130 mm total power requirement: 1,1 kw weight of the machine ca.: 570 kg dimensions of the machine ca.: 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2100 mm plate thickness: 8 mm pre-bending: 6 mm upper roll diameter: 190 mm lower roll diameter: 170 mm side roll diameter: 150 mm total power requirement: 3 kW weight of the machine ca.: 3.450 kg Machine dimensions approx.: 4040x1380x1255 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
シートの厚さ:1.25 mmローラー本体間隔:250 mm投影:260 mmローラー中心距離:62 mm取り付け:26 mm 速度:6.3 m /分 総電力要件:0.7 kW 重量:170 kg 寸法L-W-H:1020x600x1500 mm 機器: - 電動ビーズマシン - 浸透ローラー5 セット - フットスイッチ - ドイツ語 の取扱説明書 - CEマーク/適合宣言書 ! サービスとしてのあなたのための!前払い金、残余価 値、個人的なアドバイス、および要求に応じて個々 リース率の計算なしで、 最大60ヶ月の機械リース。 この広告のデータは、LogoTech oHGのマシン管理であるModulMWSで作成されました。
bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
シートの厚さ:4 mmローラー本体間隔:260 mm投影:500 mm ローラー中心距離:132 mm 取り付け:40 mm 速度:5 m/分 総電力要件:2.2 + 0.55 kW 機械重量約:450 kg スペース要件約:1800x700x1600 mm 機器: - 高調波は油圧でオンとオフを切り替える ことができます - 浸透ローラー3 セット - フットスイッチ - ドイツ語 の取扱説明書 - CEマーク/適合宣言書 ! サービスとしてのあなたのための!前払い金、残余価 値、個人的なアドバイス、および要求に応じて個々 リース率の計算なしで、 最大60ヶ月の機械リース。 この広告のデータは、LogoTech oHGのマシン管理であるModulMWSで作成されました。
sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 200 mm min. bending diameter: Ø 300 mm bending speed: 5 m/min total power requirement: 5,5 kW weight of the machine ca.: 4.000 kg dimensions of the machine ca.: 4800x1300x1270 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 4100 mm plate thickness: 35 mm pre-bending: 28 mm upper roll diameter: 540 mm lower roll diameter: 541 mm side roll diameter: 440 mm total power requirement: 37 kW weight of the machine ca.: 48.100 kg Machine dimensions approx.: 7670x3000x2930 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
シート厚さ:2.5 mm ローラー本体間隔:260 mm 投影:500 mm ローラー中心距離:92 mm 取り付け: 35 mm 速度:3.5 m/分 総所要電力: 1.5 kW 機械重量約: 295 kg 所要スペース 約: 1200x700x1200 mm 設備: - 電動ビーズマシン - 浸透ローラー3 セット - フットスイッチ - ドイツの 取扱説明書 - CEマーク/適合宣言書 ! サービスとしてのあなたのための!前払い金、残余価 値、個人的なアドバイス、および要求に応じて個々 リース率の計算なしで、 最大60ヶ月の機械リース。 この広告のデータは、LogoTech oHGのマシン管理であるModulMWSで作成されました。
シート厚さ:4 mmローラー本体間隔:260 mm投影:500 mm ロール中心距離:132 mm 取り付け:40 mm 速度:5 m /分 総電力要件:2.2 kW 機械重量約:350 kg 所要スペース約:1650x700x1280 mm 機器: -電動ビーズマシン -浸透ローラー3 セット-フットスイッチ -ドイツ語 の取扱説明書-CEマーク/適合宣言 ! サービスとしてのあなたのための!前払い金、残余価 値、個人的なアドバイス、および要求に応じて個々 リース率の計算なしで、 最大60ヶ月の機械リース。 この広告のデータは、LogoTech oHGのマシン管理であるModulMWSで作成されました。
table diameter: 1300 mm table load: 7.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M24 Tilt Angle: 90-180-100 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 3.050 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 25 mm pre-bending: 20 mm upper roll diameter: 390 mm lower roll diameter: 360 mm side roll diameter: 300 mm total power requirement: 18,5 kW weight of the machine ca.: 17.100 kg Machine dimensions approx.: 5800x2100x2000 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ...
round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
シート幅:1050 mm シート厚さ:1 mm ロール直径:56 mm 所要スペース 約:1600 x 700 x 1050 mm 機器: - トップローラー手動回転 オプション装備: - 硬化ローラー! サービスとしてのあなたのための!前払い金、残余価 値、個人的なアドバイス、および要求に応じて個々 リース率の計算なしで、 最大60ヶ月の機械リース。 この広告のデータは、LogoTech oHGのマシン管理であるModulMWSで作成されました。
sheet width: 2100 mm plate thickness: 13 mm pre-bending: 10 mm upper roll diameter: 230 mm lower roll diameter: 210 mm side roll diameter: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4.620 kg dimensions of the machine ca.: 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...
table diameter: 960 mm table load: 3.500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M20 Tilt Angle: 70-90-180 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 1.500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
シート厚さ:2.5 mmローラー本体間隔:260 mm投影:500 mmロール中心距離:92 mm取り付け:35 mm 速度:3.5 m /分 総電力要件:1.5 + 0.55 kW機械 重量約:320 kg スペース要件約:1200x700x1200 mm 機器: -高調波は油圧で上下に切り替え ることができます-ビードローラー3 セット-フットスイッチ -ドイツ語 の取扱説明書-CEマーク/適合宣言書 ! サービスとしてのあなたのための!前払い金、残余価 値、個人的なアドバイス、および要求に応じて個々 リース率の計算なしで、 最大60ヶ月の機械リース。 この広告のデータは、LogoTech oHGのマシン管理であるModulMWSで作成されました。
table diameter: 715 mm table load: 500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-110 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 675 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 10 mm pre-bending: 8 mm upper roll diameter: 270 mm lower roll diameter: 250 mm side roll diameter: 210 mm total power requirement: 11 kW weight of the machine ca.: 7750 kg Overall size: 5600x1450x1600 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
