We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
123,281 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
This DOOSAN HP 6300 Horizontal Machining center was made in 2007 in Korea. It is equipped with a Fanuc Series 18i-MB control unit.
used
Film imagesetter Linotronic 630 Post Script RIP 50 exposure format: 483x450mm (19x17.7inch) without register option 483x428mm (19x16.9inch) with register option Material width film: 280,310,340,370,400,430,460 mm Min. width and length not specified Dimensions (W x H x D) 820 x 890 x 960 mm (32.2 x 35 x 37.8 inch)
used
wheel alignment scissor lift 5t, galvanized, Specifications: Stroke underfloor 1,800mm, stroke above-ground 2,160 mm Overall length 5,200 mm, overall width 2,300 mm, ramp height 360 mm, platform length 5,200 mm, Platform width 729 mm, motor power 3 kW, electrical connection 230/400V, 50 Hz, compressed air connection 6-8 bar, Lifting time 45 sec., lowering time 45 sec. Characteristics: Electro-hydraulic drive,2 maintenance-free hydraulic cylinders, No mechanical connections between the rails,Maintenance-free roller lafers, HD unit integrated in the control panel, operation via push buttons with integrated storage option, Integrated hand pump and emergency lowering in case of power failure, Hydraulic synchronization system with automatic level compensation (master-slave system)Pneumatic set-down device with automatic pressure system. Unlocking, non-contact inductive proximity swit ...
used
used
This AP&T HP 630 Stamping machine was made in 1992. It is equipped with an APT S5 control unit.
used
used
Nominal effort: 630 tons Course stroke: 420 mm Number of strokes in a minute: 20 Bolster plate-to-ram adjustable stroke: 180 mm Max. distance plate-to-ram (in lower position of slider): 750 mm Slider dimensions 1000x1000 mm Table size: 1250x1250 mm Dimensions of the hole in the table 800x800mm Thickness of the sub-stamp plate 180 mm Height above floor level 600 mm Main motor power: 56 kW hydropneumatic pillow in the table Press overall dimensions: -Length: 3280 mm -Width: 3470 mm -Height: 6190 mm Press weight: 52650 kg
used
Type: 9375 Retrofitted in 2017 with Siemens 840D - max diameter to be turned to centre: 6100 mm - max workpiece height under arm: 2600 mm - vertical travel of ram: 1250 mm - horizontal travel of ram: 1250 mm - swivelangle of tooldhead: 45° + 30° - turntable is movable in order to accomodate workpieces up to 6 meter in diameter - max load on table: 50 ton Chuck dia.: 3300 mm Max turningdia -- passage: 6300 mm Power on the spindle: 75 HP Max hight of workpiece Z-axis: 2600 mm Command: Siemens 840D Number of speeds: 0.60 > 60 rpm Weight: 93 ton TOOLING: yes
used
Type: HPDb 630-2500/1400 factory number H/7447, year of production 2000 Double-column press Pressing force 630-6300 KN Lifting force 750 KN Stroke 1000 mm Lifting speed from 450 mm/s Load 16-50 mm/s up to 450 mm/s Drive power 2x 55 kW Blanking shock dampers Damping force 6300 kN Damping stroke 15 mm Spindle adjustment path 400 mm Auxiliary unit 35 kW Bed area 2500 X 1400 mm Press data Press weight approx. 100,500 kg Tool weight max. 10,000 kg Hydraulic oil weight approx. 3420 kg Foundation load static approx. 1140 KN dynamic approx. 230 kN maximum load = Fstat. + Fdyn. Oil tank capacity approx. 4020 liters Installed power approx. 155 kW Current consumption approx. 275 A Control cabinet Length approx. 2400 mm Depth 500mm Height 2200 mm
used
Mobile
used
new
: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 67700 € : 1374.31 € : 63 to : 750 mm : 500 mm : 170 mm : 4 - 102 mm : 54 1/min : 490x325 mm : 90 mm : 270 mm : 440 mm : 7,5 kW : 1800 mm : 1150 mm : 2750 mm : 4100 kg 8-fold ram guide front protection by light guard manual stroke adjustment ram adjustment witch ratchet drive over gear combined clutch brake unit with pneumatic control fix table single and continuous stroke foot pedal and 2 hand control mech. overload safety device automatic central lubrication user manual in GERMAN and ENGLISH according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Magnetic clamping table 600x350mm Machine already ready for transport, machine can be viewed on viewing day for correct assessment.
used
A used dough sheeter from Fritsch Model Rollfix 3-630 with 60cm bandwidth is currently for sale and immediately available in our warehouse. Dough sheeter Fritsch Rollfix - used Fritsch Rollfix sheeting machine - with 60cm bandwidth - right left rotation - with manual and foot switch - Band length 116cm each External dimensions approx.: Length: 244cm Width approx.: 80cm Height: 110cm
used
Machine already ready for transport, machine can be viewed on viewing day for correct assessment.
used
Mobile
used
rated capacity: . kVA capacity in kVA: . kVA Heating capacity: . kW power fuel: . 0 weight of the machine ca.: . t dimensions of the machine ca.: . m Construction site electricity distributor 550 x 400 x 1350 The techn. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
WMW - Cylindrical grinding machine Type SA 5x630 Center height approx. 140mm Center width approx. 630mm Grinding wheel puller Measuring device Coolant device B0pegjgotf Switchboard Work lamp Dimensions LxWxH approx. 3x2x2 meters Weightapprox. 4000Kg EXTENSIVE RANGE OF GRINDING WHEELS AND MOUNTING FLANGES. COMPLETE TECHNICAL DATA CAN BE EMAILED ON REQUEST BECOME.
used
Description Electrical drawing machine 12 zone mold heating software package n ° 1 and 2: extensive control of the mechanical mold functions for complex applications, extended movements software package n ° 3: production control software package n ° 5: optimization helps the operator software package n ° 6: quality assurance software package n ° 7: documentation with real value protocol
used
Used Band Saw Manufacturer: HEMA Type UH 630 YOC 1990 Roll diameter 630 mm Cutting height 570 mm Cutting width 610 mm Motor power 1.5/2.2 kW 2 speeds Belt length 4,950 mm Table swivel by handwheel Scale and Zero Lock Transport height with pallet approx. 2.50 m Weight approx. 380 kg With large Pos. saw blades Rriy9e2lqn With brake & instructions Item location: 59425 Unna The machine can be viewed under power. A forklift for loading is available. Prior sale is reserved. It is possible to professionally examine the items for sale on site. Specific questions should be clarified in advance. The information, such as technical data, dimensions, year of construction, condition, is non-binding and has been shown to the best of our knowledge and belief. Errors are therefore reserved. The warranty / guarantee is excluded. The goods are sold from the location / w ...
used
TS 631 wireless tracer with ISO 40 tool taper and various accessories in wooden box
used
Manufacturer: WMW Type: DLZ 630x2500 E IV Stock number: 0979 Year of construction: 1965 Turning length: 2500 mm Orbit diameter over bed: 630 mm Speed: 1455 rpm Voltage: 380 V Motor power: 10 kW Dimensions (LxWxH): 4800 x 1900 x 1750 mm Machine weight: 4.85 t
used
x-travel: 635 mm y-travel: 510 mm z-travel: 460 mm control: 840 D sl ShopMill Siemens Main spindle:: turning speed range - main spindle: 20 - 10.000 min/-1 power capacity - main spindel: 13 / 9 kW tool taper: SK 40 max. Torque: 83 / 57 Nm tension force: 8 kN work table:: table surface area: 790 x 560 mm number of T-slots: 4 + 1 T-slot - distance: 100 mm T-slot - width: 4x 14H12 / 1x 14H7 mm max. table load: 600 kg table height over floor: 720 mm distance spindle nose and table: 120 - 580 mm Tool-Presetter:: number of toolpositions: 20 pos. Max. mould width: 80 / (130) mm max. tool length: 250 mm max. tool weight: 6 kg max. total weight: 80 kg change-time tool to tool: 1,6 sec change-time chip to chip: 6,0 sec feeds:: rapid traverse: 30 m/min feed speeds: max. 30.000 mm/min Feed force: max. 5 kN total power requirement: 23 kVA weight of the machine ca.: 4,5 t dimensions of the machine ...
used
SHELVING SYSTEM STOW 37 LFM H:590 / 635 CM SECOND-HAND GOODS Data: H : approx. 590 / 635 cm D : approx. 110 cm L : approx. 37 m Load: 1600 kg shelf load Stand in grey Trusses 360 cm Trusses in orange Used goods from stock Wietmarschen Shelf consists of : 11 x stand approx. 590 / 635 cm x 110 cm 60 x truss approx. 360 x 12.5 cm 120 x locking pins. Levels: Floor + 3 160 pallet spaces Price: 3750,00 € Net plus statutory VAT. You will receive an invoice with VAT.
Container aggregate 650 kVA PRP Power: 650 kVA / 520 kW PRP Operating mode: 1500 rpm Voltage: 400/230 V Power factor: 0.8 Engine: MTU | 12V1600G20F-3E Generator: Stamford | HCI544F Automatic electrical panel with circuit breaker 1000A / 4P and Automatic control COMAP Inteligen 500 with GPRS/4G/antenna Fuel system: 950 litres internal in the base frame Cooling water heating with backing pump Exhaust gas optimized Leak monitoring Indoor 3-way valve for connection from an external Tank Dimensions 20 feet HC container: Length: 6,058 mm Height: 2,896 mm Width: 2,438 mm
used
Label Printers Industrial Printers Thermal Transfer Direct Thermal Printers 1 x Honeywell Label Printer DMX-A-4212 New from Spare Stock 1 x Honeywell Label Printer DMX-A-6310 New from Spare Stock
used
GLUING MACHINE, STORK, TYPE: ERT 630 Technical description: Bandwidht: 630 mm Material: Stainless steel Aisi 304 Power supply: 380/440 V - 50/60Hz Dimensions: 1500 x 1200 x 1800 mm
used
Panel size: 630 mm x 630 mm, Number of plates: expanded from 15 to 30 Panel thickness: 50 mm Cake thickness: 25 mm Hydraulics: motorized Filtrate drain: open Weight; 1500 kg (approx.) Pressure: 15 bar (max. feed pressure). The press is still in operation and will be used for industrial wastewater treatment. Discharge chutes below the filter press.
used
BREADING MACHINE MAREL TOWNSEND FURTHER PROCESSING B.V., MODEL: TRM 630 Technical description: Marel Townsend Further Processing B.V. rolling machine. Model TRM 630 Type 472640 Serial number 10096047 Plastic belt, belt width: (2x) 630mm Total dimensions: 2050mm x 1300mm x 2100mm
used
Panel size: 630 mm x 630 mm, Number of plates: expanded from 25 to 50 Panel thickness: 50 mm Cake thickness: 25 mm Hydraulics: motorized Filtrate drain: open Weight; 1500 kg (approx.) Pressure: 15 bar (max. feed pressure), Diaphragm pump Closing pressure at the pressure gauge 380 bar Hydraulic; Type GL KES 401-50 Machine dimensions: L 4450 x W 1700 with protective grille x H 1700 mm. Discharge shaft can be taken along. The plant was regularly serviced. The press is still in operation and is used for industrial wastewater treatment. Discharge chutes below the filter press.
used
Control: Heidenhain TNC 430M, connected load: 30kVA, operating hours: 27,879h, the machine is heavily used, X- and Y-axis need to be overhauled, the motor of the Z-axis is defective, an on-site inspection is possible.
used
BREADING MACHINE, TITAN INTERNATIONAL, TYPE: TPM 630 Technical description: Serial number: 871038 Material: Stainless steel Mesh widht: 630 mm Hopper load capacity: 208 Lt Power supply: 380-440 V / 50-60 Hz Dimensions: 1850 x 1000 x 2000 mm
used
X-travel: 630mm, y-travel: 500mm, z-travel: 500mm, table diameter: 900x528mm, NC rotary table diameter: 500mm, connected load: 14kVA, length: 3600mm, width: 3900mm, height: 2100mm, weight: 6t, with documentation.
used
Grinding range X/Y/Z: 600mm/375mm/375mm, grinding wheel: 300mm/50mm/76.2mm, max. table load: 300kg, table clamping surface X/Y: 900mm/350mm, weight: 3300kg. Including hydraulic system, self-made extraction system. X/Y/Z axes limited in function. Documentation available. On-site inspection is possible.
used
Length: 2100mm, width: 1200mm, height: 2000mm, weight: 3.35t.
used
Punching force: 630kN, stroke adjustment: 10-80mm, ram adjustment: 80mm, stroke speed: 65-400/min, connected load: 11kW, length: 1590mm, width: 1650mm, height: 3000mm, weight: 9.5t, with documentation.
used
Machining diameter 500 mm max. turning diameter 660 mm Workpiece length 300 mm ----------------------------------------------- Working axes Total stroke X-axis 1180 mm Working stroke X-axis 370 mm Working stroke z-axis 400 mm ------------------------------------------------ Electrospindle Spindle speed up to 1600 1/min Max. power 46 KW Max. torque 2517 Nm CNC control Siemens 840D Driven tool stations Coolant system Conveyor Air extraction system
used
Weight: 371kg.
used
pressure: 630 t passage width: 1390 mm stroke: 400 mm table surface area: 1390x1250 mm total power requirement: 75 kW weight of the machine ca.: 36 t dimensions of the machine ca.: BxTxH 3200x2800x4000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
2 Sibre TE 630/1250/60 Retail sale possible
used
There are 2 identical SGB transformers available. Theoretical power: 630kVA, peak power: 340kVA, average power: 300kVA. The transformers are only sold as a package deal. Individual machines cannot be sold separately.
used
HANDTMANN VF-630
used
Circular saw Frommia 630 Length 1.20 m Width 1 m Height 1 m Attack Roller table Saw blade
used
used
MAN D2066 cylinder block 51.01100-6361 / 51.01100-6371 for 2850 Euro / each., The block is used in good condition, delivered with 3 months warranty.
used
Quaser MF 630 five-axis milling machine. CNC control system Siemens 828D Travel in X/Y/Z axis (mm) 800/700/610
new
Roll diameter: 600 mm; Stand projection: 570 mm; Cutting depth: 400mm; Swivel table: yes -0 to + 45Â; Table size: 830 x 600 mm; Belt speed: 1615m/min; Motor power: 3.75 kW / 400V; Engine brake: yes / automatic; Extraction port: 2 x 120mm; Machine length: 1190 mm; Machine width: 780 mm; Machine height: 2063 mm; Weight: 380 kg; DESCRIPTION Heavy-duty professional design with high dead weight for maximum smoothness Particularly quiet and precise running thanks to torsion-free machine housing Large-dimensioned cast iron saw table made of one piece, swivelling from 0Â to +45Â with ground and polished surface Patented table tilting device with handwheel and rack Saw blade quick clamping Precision saw band roller guide Fast and precise cutting height adjustment via handwheel and rack with millimeter scale Safety switch for automatic shutdown when the door is opened Large cast i ...
used
Line for PVC profiles : 1.Extuder Single Theysohn AS 63mm PVC 2. Calibration table Greiner Genius Cal 2P/3.6 3. Theysohn REA32/1HJ-TECH belt lashing 4. saw Theysohn REA32/1HJ-TECH) price for all Line 25.000 Euro
used
Manufacturer: SMG / Feintool Type: HFA 6300 Year of construction: 1988 Total force: 4000-6300 kN Ring serrated force: 320-3200 kN Counter holding force: 130-1300 kN Safety distance: 153 mm Trailing distance max. 10 mm Closing speed: 120 mm/s Plunger stroke beu max tool height: min.-max. 30-150 mm Tool clamping surface at the top: 900 x 900 mm Tool clamping area at the bottom: 910 x 1350 mm Tool installation height max: 410 mm Tool installation height min: 330 mm Main drive: 90 kW Total connected load: approx. 120 kW Weight of the press: approx. 31 t
used
Emergency power supply system as a 630 kVA diesel generator in a soundproofed container from a DATA Center with MTU 12 V 2000 engine Aggregate type: stationary Version: container Technical data engine: Engine manufacturer: MTU Engine type: 12 V 2000 Engine No.: 535102610 Engine power: 565 KW Cooling: Water-cooled Tempering: Electric 24 V DC Speed: 1500 rpm Fuel: Fuel oil EN 590 Technical data generator: Generator manufacturer: FKI Marelli Generator type: M8B 400 SB4 B3 Gene. Item no.: HM28 167-11 Generator power: 630 kVA Voltage: 400 / 231 volts Power factor: cos. - PHI 0.8 Speed: 1500 rpm Switchgear: Execution: Automatic start Functions: Emergency power operation Switch: no switch Delivery: Assembled Tank, version: Mounted on the container Capacity / litre: 4.200 Dimensions of the p ...