then used for sale

New cooling water distributor 25 duct with very high-quality components - ready for connection The manifold was made for a large vacuum system, which was then not accepted. It was made in 09/2018 and then fully shrink-wrapped and packed in a box. Today the distributor was unpacked for photos. - 25 cooling circuits - 3 x ifm SM8000 magnetic-inductive flow meter - 22 x ifm SM6000 magnetic-inductive flow meter - 4 x ifm AL1222 IO-Link master with EtherNet/IP interface - A VA ball valve from ECON at the supply and return, 50 pieces in total (different sizes) - a Swagelok proportional RL3 overflow valve on each channel (various dimensions) - Pressure and temperature measurement in flow and return - Swagelok fittings The distributor is about 3m wide. It can be viewed by appointment in Dreye near Bremen

PEELER- SKINNER, TRIO, TYPE: FDS 104 Technical description: Plastic wired belt Belt width: 350 mm Power supply: 380/440 V - 50/60Hz Dimensions: 2200 x 1200 x 1500 mm The TRIO FDS Skinning Machine will skin most kind of fish fillets. The machines are used for skinning Sale and other flat fish, Hake, Haddock, Whiting, Merluza, Hoki, Orange Roughy, Herring, Mackerel, Sardines, Salmon, etc. The machine operates on the principle that the skin of the fillet freezes and glues to the cold, rotating drum, and thus is held in position. The freezing is approx. 1/10 mm deep. A rotating band knife cuts the fillet away from the skin, and the skin is then scraped off the drum. The thickness of the cut, and thus the depth of the skinning, is infenitely adjustable between 0-12 mm. The refrigeration system operates on a system of indirect cooling, a sealed refrigeration unit cooles down a secondary cool ...

METRIS-NIKON MCA II 5124 measuring machine built in 2011 is a versatile device that can be used for measuring both small-sized objects as well as complex, large-sized parts. In addition, thanks to the computerisation of measurement procedures and its compact design, the machine can be used directly in the production environment or even inside the measured objects. The measurement process starts with an angular displacement of the arms to ‘pass’ through reference points. The operator then brings the machine’s measuring tip to the surface of the measured workpiece and validates the coordinates using a button located on the head. The coordinates are then transformed by the calculation procedures to the cartesian system (X,Y,Z), where they are used as the basis for determining the dimensions by approximation of the measured features and geometric figures, i.e. circles, cylinders and ...

AUTOOL HTS708 Automotive Dry Ice Cleaning Machine AUTOOL HTS708 Automotive Dry Ice Cleaner is a multi-purpose cleaning machine for the automotive repair and service field, which can be specially used for car engine carbon cleaning. The dry ice particles are accelerated by a high-speed airflow to remove carbon deposits. The cleaned dry ice evaporates in the environment and is safe and residue-free without damaging the vehicle. It can be used to clean the engine compartment, cylinder combustion chamber, intake valve, throttle valve and other carbon deposits, which serve the purpose of multi-purpose cleaning and maintenance. The device is particularly outstanding in terms of safety, reliability, intelligence and ease of use. Well designed The overall structure of AUTOOL HTS708 auto dry ice cleaner is simple, lightweight and practical. This device is equipped with a trolley bar, a  ...

Length: 2700 mm Width: 1100 mm Height: 850 +- 150 mm engine output: 0,37 kW Electric capacity: 0,5 kw compressed air: 6 bar Horizontal impregnation system Pro flow for individual parts with rinsing circuit. --------------------------------- Features: Machine for horizontal flooding of individual parts. The product will go through flooded a row of nozzles. The excess product is then removed through air jets blown off. The pump and the air nozzles are controlled automatically and only then operated when the workpiece passes through. In this way the Compressed air consumption reduced. The circulation operation ensures minimal product consumption. --------------------------------- Construction features: structure Sturdy steel frame, painted with high-strength, water-soluble products. Machine body made of heat-sealed, thick polypropylene plates. 4 independent chambers for inlet, flooding, blo ...

OKUNO MSC-15 spring coiling machine was manufactured in 1998 in Japan by OKUNO Machine Co. The machine designed for the efficient production of springs from wire with a maximum thickness of 0.3 mm, consists of a wire spool rack with a braking system, a heating device for annealing and a forming machine. The wire processing process begins with taking material from a spool mounted on the machine stand, which is then fed into the heating device to anneal both ends of the spool. The pre-treated material is then fed further into the forming machine, where it is shaped into a spring by automatic cutting and bending. The length of wire feed is regulated by a digital indicator located on the machine frame. Technical data of the OKUNO MSC-15 spring coiling machine - maximum wire feeding length: 10m ± 5 mm - thickness of material: 0.15 – 0.3 mm - material width: 5.0 – 15.0 mm - maxi ...

Labeling machine for containers adaptable to industrial lines or manual loading. Variable data printing Ideal for automatic or manual loading. Machine produced by SCM Costruzioni Macchine Italia - Line Lat model, year 1999, Voltage 380-50 Hz - 3 phases TECHNICAL FEATURES: - WEIGHT 600 Kg mm. - ABSORBED POWER 1,5 Kw. - POWER SUPPLY 380 + N Volt 50Hz - AIR CONSUMPTION 15 l./min - AIR PRESSURE 4.5 bar - OVERALL surface 2500x870 mm - HEIGHT max 1800 mm - VARIABLE DATA MARKER Thermal transfer Ribbon - Ribbon foil transfer system Operation description: The linear labeling machine with self-adhesive group LINE LAT LAP-LAT can be inserted in automatic packaging systems for containers of any type and shape. The containers are spaced before entering the machine by centering rollers placed on the sides of the conveyor belt. They are then guided by a counter belt which has the task o ...

Sawn timber sorting and packaging line 2.90-5.20m Sequence description Dispensed Home & Dispensers Side goods are collected separately by means of conveyor belts into two stacks on top of each other. The storage tanks are emptied via the separation conveyor to the board feeder and board turner. At the Zuteil-u. The operator is located at the turning station, who is responsible for monitoring and assessing the quality of the boards. All boards are inspected from two sides and then electronically measured, this is done according to length, width, thickness and thickness. Quality in transverse transport. About the Wende-u. The cut goods are sent to the sorting conveyor, after which they are sorted into the 30 boxes At the end, stray sorting conveyors are transported away by conveyor belt. The belt boxes are emptied by lowering and disengaging the belts. Subsequently, the respectiv ...

intake connection: 200mm; Maximum volume flow: 1770 m³/h; nominal volume flow: 2780 m³/h; Vacuum: 1580 pa; filter area: 13 m²; filter regeneration: pneumatisch; chip bag volume: ca. 380l; motor power: 3 kW; machine length: 2000 mm; machine width: 800 mm; machine height: 2200 mm; weight: 240 kg; The deduster is suitable for extracting dry wood dust and dry wood chips on individual dust sources. this is also valid for oak and beech wood dust. Furthermore, metallic, ceramic mixed, organic dusts of the dust ex plo sions class St1 and St2 be sucked off. If the dust extractor is properly handled by a woodworking machine with a dust source (eg circular saw, milling machine, planer machine, belt grinder) and locked in accordance with the rules operated, is the necessary extraction performance and separation quality always guaranteed. When extracting a dust-proofed woodworking m ...

New Can Sealer 60 heads 30 000 cph Available with 70 HEADS Production per hour 45 000 90 HEADS Production per hour cans 60 000 1 ADVANTAGE OF THE SYSTEM Guarantees the hygiene of the can both in upper and lateral part Applied dry without the use of glue or heat Allows to the final user to drink directly from the can Improves the qualitative image of the product Permits the usual stacking of the cans Guarantees watertightness for immersion Suitable also for warm distributors 60 C Compatible with the traditional Multipack systems Decoration and customization is possible for marketing and promotional purposes Adds a possible advertising space on the product 2 MACHINE DESCRIPTION Automatic machine for the application of a polyethylene stretch film on the cans The machine inferior structure and external walls of the machines base are constructed completely of stainless steel AISI 304 The supp ...

OMAS model ML16 Monobloc fully automatic machine, constructed in 316L grade stainless steel, Four head inline diving head liquid filling station, positive shut off tips can be used if required. Variable speed 100mm wide slat -band conveyor and infeed/out-feed gating control. Star-wheel transfer of filled bottles to the plugging/ insert and cap placement station supplied from two stainless OZAF vibratory feeders located at the rear of the machine. Bottles then progress to the pre-set torque capping station and then back onto the line conveyor. Separate control panel for all machine functions. It is fully guarded with electrical safety interlock devices on all opening panels. Fill range 50 to 500ml: max bottle dia 65mm: max speed 50 bpm: Installed power 4kw: Approx overall dimensions 2.7 x 1.7 x 2.1m high: weight 1,300kg. Standard nozzles to be supplied to suit clients bottles.

Model: JDM650-BIB Function: High-speed, Automatic Bag In Box Bag Making Machine; Tap & Nozzle Automatic Put Online Feature: 1. Bag have 4pcs film; 2. Punch on film, then welding nozzle, make bag; 3. Two units main unwinding; 4. Inverter motor control unwinding continuously, loop control system control tension steadily and reasonably; 5. Triple AC servo motor infeed film, ensure system tension reasonably and steadily, faster and correct, film non deformation; compare with normal machine, main drive is AC servo motor, ensure high production ratio and enough sealing time; 6. Vertical & horizontal use heating and cooling finalize the design, make sure good sealing; 7. Automatic nozzle structure is consist of nozzle stock bin, lifter, vibrating disk, belt, nozzle; 8. High degree of automation, nozzle reliability, ensure bag cleaning; 9. PLC control whole machine, HMI paramete ...

Automatic line for packaging products in shrink film Kallfass Compact 450. 1. Appointment. The line is designed for packaging products in shrink film. 2. Working principle. Products from the conveyor of the production equipment enter the feeding conveyor of the packaging line. On the infeed conveyor, the product is aligned along the line of motion and then enters the inlet conveyor of the film packaging section. In the packaging section, the products, moving along the introductory conveyor, enter the inside of the half-sleeve of the packaging film, and then move along with the film to the zone of the transverse knife. The cross cutter cuts the film to a predetermined length while sealing it. Further, the product in the film passes to the output conveyor, where the longitudinal knife cuts off the side of the film, also sealing it at the same time. After that, the completely ...

The Urschel Model GK slicer allows you to cut ripe, soft fruit and crispy root vegetables in a variety of ways. These include classic even cubes, stripes, posts and straight and wavy patches, and even three-dimensional shapes with four wavy and two flat surfaces. The device is especially recommended for cutting wavy potato fries. Due to the direct contact with the food product, the equipment is equipped with high-quality parts made of stainless steel. The notch works smoothly, does not jam, offering an uninterrupted work cycle. Experienced Urschel specialists have made sure that the device is easy not only to use, but also to clean and maintain. Equally important, buyers of this ice maker get a wide range of interchangeable cutting parts. Thanks to this, it is possible to obtain delicate, clean cuts in a large range of sizes. Additionally, the machine can be equipped with any cutti ...

size of profile - max.: 150 mm Number of drilling agregates: 1 Stk. bore diameter: 35 mm quill stroke: 140 mm spindle taper: MK 4 column diameter: 120 mm throat: 300 mm distance spindlenose - table min./max.: 50 / 600 mm spindle turning speed range: 14 / 45 - 1650 U/min impact length: 3000 mm base plate: 420 x 420 mm Max. speed ot the feeder: 200 mm/sec. positioning accuracy: auf 3 m +/- 0,2 mm air consumption: 6 bar boring motor: 1,5 kW Carrying capacity feeder: 45 kg Control: weight of the machine ca.: 500 kg dimensions of the machine ca.: ca. 2,5 x 0,7 x 2 m CE signed: Condition: ready for operation: Video(s) available on our website.: Electric 400 Volt: Cooling equipment (Micro-Cooler): Luft - Öl Protection made in plastic: Controlled SERIES DRILLING MACHINE used very little with 3 automatic spindel feeds in conjunction with the automatic speedy feed system suitable for pipe a ...

Suction nozzle diameter: 200mm; Nominal flow rate: 2780 m³/h; Volume flow monitoring: pressure differential indicator; Negative pressure: 1580 pa; Filter area: 13 m²; Filter cleaning: pneumatic; Motor power: 3 kW; Machine length: 2000 mm; Machine width: 800 mm; Machine height: 2200 mm; Weight: 240; The dust extractor is suitable for vacuuming dry wood dust and dry wood chips at individual dust sources. This also applies for oak and beech wood dust. Furthermore, metallic, ceramic, organic dusts of dust explosion class St1 and St2 can be extracted. If the dust extractor is properly connected to a woodworking machine with a dust source (e.g. circular saw, milling machine, planer, belt sander) and operated in accordance with the regulations", the necessary extraction performance and separation qualityâ is always guaranteed. When vacuuming a “dust-tested†woodworking  ...

6 head liquid filling machine WITHOUT cup dispenser. Bottles are fed to the conveyor by manual and then bottles are conveyed to filling station. After the photoelectric sensing of 6 bottles, the filling head will go down and when filling finished, the bottle will be conveyed to the star wheel, mechanical arm feed the cap and then the capping system will screw the cap. Filling speed: 20 - 60 pcs/min Filling range: 50 - 1000 ml Filling accuracy: +/- 1,5% Dimension: 2500×1200×2200mm

Filling system for sprouted vegetables, consisting of:, - Plate conveyor belt for containers, runs through chamber filler, - Product feed hopper for feed screw, Dimensions feed hopper: L x W x H = 850 x 800 x 400 mm, - Feed screw for product, Distance between the screw flights: approx. 160 mm,, Screw diameter: approx. 320 mm, length: approx. 8000 mm, - Belt conveyor belt make Niko type 02703022, machine number 403980,, blue smooth belt: approx. 2100 mm, usable width: approx. 340 mm, Belt conveyor belt for product transfer from the feed screw to the multihead weigher, - Multihead weigher with 14 heads, corrugated stainless steel sheet, make Klinger, type CW14, opening of the weighing container approx. 140 x 130 mm, - Stainless steel platform for multi-head weigher, Dimensions: approx. 3500 x 3500 mm, plateau height approx. 3000 mm, - Chamber filler TK 12, type 381, machine number 40395/01 ...

Many of our machines are available from stock. Call and ask to find out more. Handheld laser welder LWH-2000-N RayTools The kit includes: - laser welder with built-in cooling system - welding gun with adjustable focal length and an accessory kit - fiber laser source of MAX Photonics or Raycus - automatic wire feeder - set of cords - starter kit of protective lenses and nozzles Specifications - Laser source output 2000 W - Laser wavelength 1064 nm - Welding speed up to 120 mm/s - Power supply 3x400 Hz - Dimensions (including cable rack) 630x1300x1500mm Price included One-day training along with machine installation - 1 day up to 8 hours – machine installation and operational training. Operation Due to the revolutionary welding system, any user can achieve good working results after just a short training. The electrode feed cable allows the welder to work fr ...

Many of our machines are available from stock. Call and ask to find out more. Handheld laser welder LWH-3000-N RayTools The kit includes: - laser welder with built-in cooling system - welding gun with adjustable focal length and an accessory kit - fiber laser source of MAX Photonics or Raycus - automatic wire feeder - set of cords - starter kit of protective lenses and nozzles Specifications - Laser source output 3000 W - Laser wavelength 1064 nm - Welding speed up to 120 mm/s - Power supply 3x400 Hz - Dimensions (including cable rack) 630x1300x1500mm Price included One-day training along with machine installation - 1 day up to 8 hours – machine installation and operational training. Operation Due to the revolutionary welding system, any user can achieve good working results after just a short training. The electrode feed cable allows the welder to work fr ...

Many of our machines are available from stock. Call and ask to find out more. Handheld laser welder LWH-1000-N QiLin The kit includes: - laser welder with built-in cooling system - welding gun with adjustable focal length and an accessory kit - fiber laser source of MAX Photonics - automatic wire feeder - set of cords - starter kit of protective lenses and nozzles Specifications - Laser source output 1000 W - Laser wavelength 1064 nm - Welding speed up to 120 mm/s - Power supply 230 Hz - Dimensions (including cable rack) 630x1300x1500mm Price included One-day training along with machine installation - 1 day up to 8 hours – machine installation and operational training. Operation Due to the revolutionary welding system, any user can achieve good working results after just a short training. The electrode feed cable allows the welder to work freely at multipl ...

This is a lid laying machine made entirely of stainless steel, designed and manufactured by us. It places lids on previously filled buckets, which are then also firmly pressed. The lids are disinfected beforehand, This machine it can be used variably and is manufactured according to your ideas and wishes. (The system is new)

Cheap used and new seeCONTAINER for sale in different versions! From current stock we can offer used and new sea containers for sale / leasing / rental: - 20ft (6m) Standard Box Container - 40ft (12m) Standard Box Container - 40ft (12m) High Cube Container - 20ft (6m) office container - 20ft (6m) sanitary container Special versions such as Double Door, Flat or Open Top are always available at short notice. Sightseeing is possible at any time and at short notice, for this we ask for a short telephone arrangement. Sea containers are extremely stable and are made of 2mm-sifted rust-coated Corten steel, which is also coated with saltwater-resistant ship paint. They have a reinforced forklift-passable floor, which is covered with 28mm waterproof hardwood floor. 20 feet (6m) of sea containers have two forklift pockets incorporated into the floor scaffolding and can theref ...

Cat.-Nr. 11-3200 new Necessary space for mash and lauter tun: LxWxH: 3 x 2 x 2,80 m Necessary space for tanks: LxWxH: 4,0 x 5,0 m complete 2 brews / day = 10hl Basic Equipment The Brew House is complete with all equipment. All equipment are with high standard an very simple to use. This 5 hl Brew House is built as 2 devices-brew house manual version with manual butterfly valve. It is possible to make 2 brews/day (10 hl) Technology All the pipes can be cleaned and sterilized in the circuit over the pump included. a) In the mash boiler the mash will be cooked, then it will be pumped with one beer pump made of stainless steel from mash boiler to the lauter tun. b) After the lauter wort will be pumped back to the mash boiler. c) After emptying the lauter tun the grit floor will be removed. The lauter tun will be changed to a whirlpool. d) After cooking th ...

Cat.-Nr. 11-3210 new Basic Equipment The Brew House is complete with all equipment. All equipment are with high standard an very simple to use. This 10 hl Brew House is built as 2 devices-brew house manual version with manual butterfly valve. It is possible to make 2 brews/day (40 hl) Technology All the pipes can be cleaned and sterilized in the circuit over the pump included. a) In the mash boiler the mash will be cooked, then it will be pumped with one beer pump made of stainless steel from mash boiler to the lauter tun. b) After the lauter wort will be pumped back to the mash boiler. c) After emptying the lauter tun the grit floor will be removed. The lauter tun will be changed to a whirlpool. d) After cooking the hops a special injection valve is introduced inside the lauter tun so that it can be used as a whirlpool. Mashing Tun / Wort Boiler Volume brutto: ...

Cat. No. 11-3210 New Plant description Sudwerk This small-sud plant comprises all components for a complete and fully functional brewing plant. All system parts used have a high quality standard and are characterized by their ease of use. The two-device brewhouse consists of a mash/spice pan and a purified vat, which is also used as a hot tub. Technical description All pipes are cleaned by a circulation pumping system. a) In the mash pan, the mash is boiled, then the mash is pumped with the beer pump into the purifier pond. b) When bluish, the wort is pumped back into the mash pan. c) After bluish, the purified vat is cleaned and the sieve bottom removed. A special injection nozzle is installed on the cylinder wall at the bottom of the läuterbottich. As a result, it can also be used as a hot tub after removing the mobile screen floor. d) After boiling the hops  ...

Metal press RMH MB (Mini Baler) This machine is particularly suitable for pressing aluminium, copper, zinc and other metals. The RMH MB Mini Baler is able to crush and then press larger material made of aluminium, copper, zinc and other metals thanks to lateral knives on three sides of the filling box. Technical data: Drive: 7.5 Kw / 400 V Weight: 1.8 T Shear lid pressure: 20 t Ground ram pressure: 40 t Working pressure: 220 BAR Filling box dimensions (L x W x D): 81.5 cm x 35 cm x 51 cm Package dimensions (L x W x material quantity): 35 cm x 20 cm x variable length (material quantity) Pressing cycle: about 1 minute Dimensions (L x W x H): 2.45 meters x 1.20 meters x 1.40 meters CE Norm Metal Baler RMH MB (mini baler) Cutting edges on three sides of the bale box and lid give this machine the ability to handle with oversized materials out of aluminium, copper,  ...

We offer the labeler after comprehensive overhaul and modernization (including cabinet). The machine is designed for bonding three paper labels on glass bottle. Implementation of fully stainless steel. Labeller is equipped with two stations: - adhesive label front, neck and back label. Scanning system and label transfer is based on the pallets, which select a label from a magazine, transfer it onto the gripper drum and then onto bottle. The machine is extremely stable and reliable. Support comes down to refill glue and charge labels into magazine. Capacity: max. 24 000 b/h. We provide 1 set of equipment designed for a customer bottle. Machine has full 12-month warranty.

Material: stainless steel Year of manufacture: 1980 Content: 1000 ltr Weight: 350 kg Length x Width x Height: 3800 mm x 1900 mm x 1900 mm Drive shaft: 6,8 kW, snail 0,6W; Drive snail: 80 1/min. We develop, plan and build for you the whole plant exactly for your needs from new and/or used machines. More then 1000 used machines on stock. Write us below!

Material: Normal steel Fan percussion More information and price on request The machine is extensively overhauled and then is as new as new.

Cheap used and new seeCONTAINER for sale in different versions! From current stock we can offer used and new sea containers for sale / leasing / rental: - 20ft (6m) Standard Box Container - 40ft (12m) Standard Box Container - 40ft (12m) High Cube Container - 45ft (13.7m) High Cube - 20ft (6m) office container - 20ft (6m) sanitary container Special Special versions such as Double Door, Flat or Open Top are always available at short notice. VISIT US Sightseeing is possible at any time and at short notice at our depot in DE-83395 Freilassing. For this we ask for a short telephone arrangement. KNOWLEDGE ABOUT SEECONTAINER Sea containers are extremely stable and are made of 2mm-sifted rust-coated Corten steel, which is also coated with saltwater-resistant ship paint. They have a reinforced forklift-passable floor, which is covered with 20mm waterproof plywood panels made  ...

Material: stainless steel Engine: 37 kW Content: 600 ltr Pressure (inner): 6 bar Weight: 750 kg Length x Width x Height: 2500 mm x 950 mm x 1500 mm Very good conditon, ready to work. Do you look for whole plant or have a questions? We have more then 1000 used machines on stock.

Cheap LAGERCONTAINER 10 feet (3m) ideal as a material/storage container from location DE-83395 Freilassing Delivery at extra cost ! DESCRIPTION / SPECIFICATION Factory-new storage containers in robust and stable design. Welded steel frame made of wood and rolled profiles with corner fittings, stackable. The floor construction consists of steel beams with welded cross beams and a covering made of 28 mm thick, water-resistant glued plywood. The walls were made of a profile plate with a thickness of 1.5 mm and are welded to the frame construction. The roof skin consists of a 2.0 mm thick profile plate. Container doors are equipped with a double lip seal and rotary rod closures. Each container has anti-theft protection and forklift bags. TECHNICAL DATA / TECHNICAL DATA Dimensions outside: length x width x height: approx. 2,991 x 2,438 x 2,591mm Dimensions inside: length x wid ...

The powder mixer can be used in any situation where powder is first added and then dissolved in the liquid. Capacity up to 100 kg/min, depending on product properties. Including stainless steels preparation table. Engine power 7.5kW. Equipped with overhauled centrifugal pump. ( Frsistam, Alfa Laval, or equivalent) As good as new.

Technical data: Fruit wash, grind, pressing then the juice pasteurization and bag-in-box packaging pour performance up to 750 L/h incl. mounted hydraulic large box emptying wash grinding plant Kreuzmayr KWEM 1000 cover press Kreuzmayr KEB 500 Pasteur Kreuzmayr PA 750 oil bag-in-box fillers Kreuzmayr CBF 900, incl. 6-digit series bottling juice pump, strainer, 2 PCs. juice buffer tank 220 litre stainless steel base frame, Tandem chassis with tyres 195/50-10 plan building with gas spring lift for the two side walls, roll-over tarp back 4 PCs. crank rotating supports for the horizontal alignment of the System cleaner, air compressor and complete piping fix established

Centrimax - Winkelhorst separation technology GmbH supplies used, but reconditioned centrifugal separators of makes GEA Westfalia Separator and Alfa Laval for the centrifugal solid liquid separation. The separators are a comprehensive overhaul and then delivered with a mechanical warranty. Furthermore, the separators with new plc are equipped with whose help the separators can be integrated easily into the existing production process. All marketed separator types (E.g. automatic drum separators) belong to the program from Centrimax.

PicoPac VM405 shell seal device for Assietten menu trays incl. heat tunnel NHG801 Sealers with two-hand control Operating the device without guard sewn-on prevents safety device on the protective cover of the press Allows remove fast and tool-less quick change facility of the pressing frame of all parts to clean the device E.g. Heating tunnel is equipped with propane gas burner (supplied with pressure reducer, but without gas cylinder) Burner has a pilot flame burner with brief interruptions to, turn back completely, and then again turn on without again having to light Adjustable chain belt speed Heating tunnel is height-adjustable and suitable for the connection to other devices Both devices must be cleaned thoroughly before operating, because dirty

Intensive mixer with horizontally aligned mixing drum, 1,500 l. useful filling, with 45 kW inoperable drive (stern wirbler, 16 knives in 8 layers, 455 UPM), 2 x 11 kW star drive, 15 kW drum drive and 3 kW hydraulic unit for automatic closure / central ground emptying. Mixing drum lined with steel, wall-to-floor scraper made of carbide, mixing blades made of wear-resistant plastic. Mischer was overhauled by a specialist company in 2005; little has been going on since then.

GranitoGrav photo-gravusystem for granite/tombstones and glass (also suitable for glazes and bottles) The CNC unit for photo engraving in stone and glass. The CNC-Fraesmaschine Series High-Z/S-400T with CNC module GranitoGrav incl. Software at a sensational price. Whether on gravestones, commemorative plaques, tiles, glass, mirror glass ... Load colour photos or photos in black and white into the CAD-CAM ConstruCAM 3D software via the specially developed module. You can then enter the output of the desired size and have milling paths calculated. This created file is opened in the machine's control software and therefore sent to the machine. - More is not necessary! It's really easy ! No programming skills are required ! The CAM software works out your data in a practical and short time and thus creates first-class photos in all the above-mentioned materials with the CNC machin ...

GranitoGrav photo-gravusystem for granite/tombstones and glass (also suitable for glazes and bottles) The CNC unit for photo engraving in stone and glass. The CNC-Fraesmaschine Series High-Z/S-400T with CNC module GranitoGrav incl. Software at a sensational price. Whether on gravestones, commemorative plaques, tiles, glass, mirror glass ... Load colour photos or photos in black and white into the CAD-CAM ConstruCAM 3D software via the specially developed module. You can then enter the output of the desired size and have milling paths calculated. This created file is opened in the machine's control software and therefore sent to the machine. - More is not necessary! It's really easy ! No programming skills are required ! The CAM software works out your data in a practical and short time and thus creates first-class photos in all the above-mentioned materials with the CNC machin ...

GranitoGrav photo-gravusystem for granite/tombstones and glass (also suitable for glazes and bottles) The CNC unit for photo engraving in stone and glass. The CNC-Fraesmaschine Series High-Z/S-400T with CNC module GranitoGrav incl. Software at a sensational price. Whether on gravestones, commemorative plaques, tiles, glass, mirror glass ... Load colour photos or photos in black and white into the CAD-CAM ConstruCAM 3D software via the specially developed module. You can then enter the output of the desired size and have milling paths calculated. This created file is opened in the machine's control software and therefore sent to the machine. - More is not necessary! It's really easy ! No programming skills are required ! The CAM software works out your data in a practical and short time and thus creates first-class photos in all the above-mentioned materials with the CNC machin ...

GranitoGrav photo-gravusystem for granite/tombstones and glass (also suitable for glazes and bottles) The CNC unit for photo engraving in stone and glass. The CNC-Fraesmaschine Series High-Z/S-400T with CNC module GranitoGrav incl. Software at a sensational price. Whether on gravestones, commemorative plaques, tiles, glass, mirror glass ... Load colour photos or photos in black and white into the CAD-CAM ConstruCAM 3D software via the specially developed module. You can then enter the output of the desired size and have milling paths calculated. This created file is opened in the machine's control software and therefore sent to the machine. - More is not necessary! It's really easy ! No programming skills are required ! The CAM software works out your data in a practical and short time and thus creates first-class photos in all the above-mentioned materials with the CNC machin ...

GranitoGrav photo-gravusystem for granite/tombstones and glass (also suitable for glazes and bottles) The CNC unit for photo engraving in stone and glass. The CNC-Fraesmaschine Series High-Z/S-400T with CNC module GranitoGrav incl. Software at a sensational price. Whether on gravestones, commemorative plaques, tiles, glass, mirror glass ... Load colour photos or photos in black and white into the CAD-CAM ConstruCAM 3D software via the specially developed module. You can then enter the desired size to be output and have milling paths calculated. This created file is therefore opened in the KinetiC-NC control software of the machine and is therefore sent to the machine. - More is not necessary! It's really easy ! No programming skills are required ! The CAM software works out your data in a practical and short time and thus creates first-class photos in all the above-mentioned m ...

GranitoGrav photo-gravusystem for granite/tombstones and glass (also suitable for glazes and bottles) The CNC unit for photo engraving in stone and glass. The CNC-Fraesmaschine Series High-Z/S-400T with CNC module GranitoGrav incl. Software at a sensational price. Whether on gravestones, commemorative plaques, tiles, glass, mirror glass ... Load colour photos or photos in black and white into the CAD-CAM ConstruCAM 3D software via the specially developed module. You can then enter the output of the desired size and have milling paths calculated. This created file is opened in the machine's control software and therefore sent to the machine. - More is not necessary! It's really easy ! No programming skills are required ! The CAM software works out your data in a practical and short time and thus creates first-class photos in all the above-mentioned materials with the CNC machin ...

The BV tests are intended for the detection of biological substances, including botulinum neurotoxins A, B, E and F, staphylococcus enterotoxina A and B, ricin and anthrax spores. BV tests use a sandwich immunoassay format. An anticoerper specific to the pathogen to be measured is immobilized on microparticles. The other anticoacher is labeled with BioVeris' BV-TAGTM label. The sample is mixed with these reagents. When the specific pathogen to be measured is present in the sample, both anticoerpers bind to it and effectively connect the microparticles, the organism and the BV-TAG marker. The reaction mixture is then transported with an assay buffer to a flow cell with an electrode that stimulates the bound BV-TAG label to emit light. Only BV tests provide this unprecedented sensitivity and accuracy. BioVeris M1M Analyzer Incl. Toughbook Panasonic Mod. CF-29HTP44BM Kunstoff Tra ...

Abbot dressing plant for chemical (Basic) media (ammonium sulphate) the plant has been used year 2010 (pump 2012) 1 x, then the company has been closed with wild diaphragm pump with ARTA dry clutch DN15 - DN150 complete documents, certificates, declarations of conformity of the individual components possibly Verohrung to but not part of the sale 2011 was once again a wild pulsation dampers for 2800,-€ upgraded Material - new price 17.000,-€, used only by the finest components from ARTA, Düperthal, wild

BySprint Fiber 3 x 1.5 m with 4.0 kW year 11/2016 cutting hours approx. 620 h Location : Baden-Wuerttemberg New price : approx. 600,000 EUR Available immediately Equipment: BySprint Fiber 3015 4,000 W Special position of the control cabinet Automatic duesen changer 40 compartment parts and cross-foerderin in the cutting area Inclusive: Incl. installation incl. system documentation incl. instruction training BySprint Fiber 4 days after commissioning Insurance 6 months manufacturer's service within Germany machine is still in use and can be inspected by arrangement. Excerpt from the then product brochure in the appendix. If you are interested, further pictures can be requested.

Pure water unit ENVIROFALK Performance in continuous operation 15 sqm / h max 18 sqm / h CA 2 trailers full of material Year 2009 / was for 1 year in use then the production has been discontinued. complete with all documents and control New price 260.000,-€

NEMESIS 9000 are high-quality, modern, by INNOVATEST developed and produced hardness tester. These versatile machines combine groundbreaking technologies and extensive facilities in a machine body with a modern design. The basic function of the hardness concept is based on a settled on the test piece nose cone's mounted a turret with up to 8 positions. The desired hardness test method can be choiceed conveniently on the large touch screen monitor by means of Visual, intuitive user interface (control and evaluation software IMPRESSIONS. Now, the operator presses START and starts the automated testing: -automatically the turret swivels the correct Indentor / lens -using search drive, the specimen surface is contacted and focused (Vickers / Brinell) -now the impression generated power-regulated -then the integrated image analysis software automatically evaluates the impression of h ...

Metallography Mounting presses ECOPRESS All ECOPRESS presses can be programmed by the user in a simple manner, that the mounting process runs fully automatically. When the ECOPRESS 50, one program can be stored in the control electronics. A rugged bayonet allows quick and safe operation. The ECOPRESS series offers a wide variety of different size of molds of 25 - 50 mm in diameter. At the same time two samples can be embedded per cylinder with an intermediate piston. Alternatively, machine type of ECOPRESS 200 twin-piston for up to at the same time 4 embeds is available. When baked in the samples into plastic granules are melted, that the sample under heat and high pressure wraps pore-free and then through a press cylinder, electronic control, integrated cooling for solidifying. ECOPRESS 50 one cylinder, electronic control, full automatic program ECOPRESS 100 one pressing  ...