maggi engineering used for sale

Working width: 650mm, working height: 910mm+/- 30mm, capacity: 50 circuit boards, connected load: 0.2kW, length: 640mm, width: 760mm, height: 1000mm, with documentation.

Continuous ageing furnace, make VEI-Engineering type: KADL 2 120 x 240 tracks: 2 furnace output: approx. 2.000 kg/h gross heating zones: 2 gas heated, 3 electrically heated max. temperature: 280°C working temperature: 180 - 200°C useable dimensions (l x w x h): 15.250 x 2.530 x 2.200 mm external dimensions (l x w x h): 28.500 x 5.800 x 6.200 mm

Fully automated page welding machine Manufacturer: Diez Type: DCE 5015 Year of construction: 2018 Operating side: in the running direction left Band-width: approx. 450 mm Clearance height: approx. 150 mm Barrel length: Endless Working height / belt height a-spout: approx. 870 mm + 100 Capacity: up to 30 cycles / min (depending on the package size and feed speed) Supply voltage: 400V AC, 50 Hz, 3 pH + N + PE Power consumption: 2 KW Nominal current: 8 A With cable and 16A CEE plug Compressed air supply: 6 bar External dimensions: Length: 1750 mm Width: 1000 mm Height: 1520 mm Description: This packaging machine automatically packaged products of all kinds in foil. Maximum flexibility through the page welding can endlessly packaging products. This allows the user to also overlong products packaging They are limited only in width and in height. But also very small p ...

Band saw Hunziker Roll ø 800 mm 3.5 HP engine Built 1952 Weight approx. 730 kg L x W x H: 120 x 100 x 230 cm The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Screw air compressor Atlas Copco GA 408 59.586 hours of operation Masch. No. ARP 230-128 Built in 1994 Weight 1.2 to L x W x h: 250 x 130 x 200 cm Fqe3oovyi 8 bar 30 kW 2925 / min 380 V 50 Hz This machine is been serviced annually by Atlas Copco. The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Fan Polytechnik L 300 Masch. No. 82261 Speed 1400 RPM Performance 7200 m3 / h Motor 380, 50 V, 7.5 kW Pressing 215 mm / WS Connection ø 300 mm H x W x d: 1080 x 950 / 1350 x 950 cm Weight 170 kg Built in 1982 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Fan Polytechnik L 200 Connection of 200 mm H x W x D: 650/1150 x 960 x 700 mm Built in 1982 Weight approx. 150 kg Masch. No. 82261 Speed 1400 rpm Leistutng 3410 m3 / h Engine 4 kW Pressing 238 mm / WS The machine is in good condition, ready for operation. Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Filter system 14 x 5 filter L x W x H: 3000 x 1280 x 2100 mm With Shaker Built in 1979 Weight 430 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Extraction system with 2 bags Connection ø 160 mm Fan 2,2 kW L x W x H: 200 x 70 x 220 cm Weight approx. 120 kg Built in 1982 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4952 Eriswil/DE-79618 Rheinfelden MATEC system + technology GmbH Mechanical engineering Mill mat 4 CH-4952 Eriswil/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Frame press Hess economic hydraulic 3600 x 2250 mm L x W x H: 400 x 100 x 270 cm Weight approx. 1100 kg year 1987 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Window slot machine REX with trimming saw and slot milling L x W x H: 200 x 150 x 160 cm Weight approx. 750 kg Built in 1976 The machine is in good condition, ready to use. This machine is available from October 2018. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Castle admission machine Drilling group, Kettenstemmer, Stulpfraese with turret stop for doors in left-right execution. L x W x H: 100 cm x 60 cm x 220 cm Built in 1982 Weight approx. 400 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Double chamber furnace, make VEI-Engineering type: KA_GB 10.14.14/d max. temperature: 550°C fan power: 2 x 4 kW heating: natural gas burners power: 2 x 100 kW useable dimensions per chamber width: 1.000 mm height: 1.400 mm depth: 1.400 mm

Gas-fired preheating furnace, make VEI type: VEI_KO_V_GB_400-350 temperature: 350°C burners power: 2 x 200 kW fans: 2 x 4 kW useable dimensions x 2 (h x d x w): 1.000 x 1.400 x 2.800 mm

Extractor fan 4 Fagida MD Year of manufacture 2002 L x W x H: 80 x 60 x 80 cm Weight approx. 120 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

CNC machining tool Morari Swivel unit with recording ISO-30 maximum speed 15000 rpm with test certificate Built in 2000 Excellent condition, ready for use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Double shaft grinder of August jade Maschinenfabrik Frauenfeld Built in 1940 Weight approx. 1100 kg L x W x H: 150 x 80 x 110 cm The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Conveyor belt Length 12 m Belt width 350 mm Drum motor Smooth belt gemuldet Head not included OCC. New price EUR 7000 Built in 1996 Weight approx. 2100 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Spindle press Reissmann AG Saalfeld-Saale for stone production of alumina Built in 1951 Weight 4000 kg L x W x H: 220 x 150 x 300 cm The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Double circular saw cross cut Rüco L x W x H: 6 x 3 x 1.2 m Weight approx. 1.5 to Built in 1969 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Vibrorinne MATEC vibrating mesh drive 4 4 kW, 3 x 400 V 50 Hz Pan nominal width 600 mm Gutter inner width 500 mm Trough depth 260 mm Extra deep OK built channel 480 mm Gutter length approx. 11'000 mm Transport speed nominal approx. 17 m / min Year 2018 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Warm air heating Spanex UL/E-50 RW-02 with chips 40 kW L x W x H: 1970 x 820 x 1570 cm Weight 530 kg Year 2012 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Vacuum pump Rietschle CLFE 61V (02) Suction capacity 60 m3 / h Final pressure 10 bar Motor 2,2 kW Year of construction 1989 L x W x H: 80 x 50 x 40 cm Weight approx. 50 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Under table saw Wadkin Cutting width 300 mm Cutting height 80 mm pneumatically raised with rolling table and stop L 2.0 m L x W x H: 2.5 x 0.8 x 1.1 m Weight approx. 480 kg Built in 1975 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Gas-heated stove Usable dimensions (stove wagon): Depth: 4,000 mm Width: 3,500 mm Height: 1,500 mm Temperature max. 1200 C Working temperature: 980 C Heating capacity: 810 kW divided into 6 burners of 135 kW Drives stove wagon: 2 x 0.75 kW Number of rule groups: 3 Control: Siemens S7 Please note that we use the ovens according to customer requirements (e.g. dimensions, temperature, type of heating).

Briceder press RSN SP 250 P Don't. # 02 782 Without a control cabinet/control Without hosting 700 l cooling water tank available for hydraulick units L x B x H: 120 x 80 x 120 cm Built in 1992 Weight about 750 kg Dismantling by buyers The machine is in good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

PRE-ALPINE REGENERATION LINE COMPLETELY REVISED, ELECTRICAL WIRING, VENTILATORS, PULPIT. EQUAL TO THE NEW! MATERIAL: PE PP PC PS ABS HOPPER WITH DOSING UNIT EXTRUDER WITH DIAM SCREW. 105 MM. 35 L/D AVERAGE PRODUCTION 300/450 KG/H BASED ON MATERIALS ENGINE: 117 KW OIL PUMP VACUUM DEGASSING PUMP centrifuge Cabinet

Vibrorinne MATEC drive rear Overtime separation and â repatriation Vibro Drive 1 electric motor 3 kW Linder nominal width inside 500 mm Preparing for 1700 mm Linen nominal length 4000 mm Peasant sheet seal unit perforation 20 mm Weight about 560 kg Built in 2018, new The machine is in very good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Magnetic drum MATEC For iron capture Length about 400 mm Drive about 0.37 kW Gearbox engine with tin slide Weight about 150 kg Built in 2018, new The machine is in very good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

UVV maintenance according to BG guideline BGR 500 Pradler Maschinen Service & Electrical Engineering Recognised maintenance technician On-site inspection , Test report Creation , Sealing Occupational safety (trailing measurement safety distance ) Operational safety according to DGUV regulation 3

Used storage heater Manufacturer Seipp Type UAGG 390- heats workpieces and ball bearings up to XXX kg With various yokes in different sizes Workbench model with swivel arm Applications: Chemical industry, steel industry, paper industry, transmission manufacturer, mechanical engineering, transport sector Voltage / Frequency / Power: 380 V / 50Hz / 35A Properties: When warming in a horizontal position, the maximum effect is achieved. Workpiece: Weight bearing max. xxx kg (other workpieces xx kg) Inner diameter 15/120 mm Outer diametermax. xxx mm Width max. xxx mm Automatic temperature: Magnetic sensor, control range 60 °C to max. 160 °C Aperture priority: Bays: Edge length 80mm, 70mm, 60mm, 40mm, 30mm, 20mm, 15mm - Induction heater - induction heater Special price

Fitting drill Ganner L x W x H: 1.20 x 0.80 x 1.40 m + stops Weight approx. 400 kg Built in 1987 The machine is in good condition, ready for operation. Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Table belt grinding machine Bürkle L x W x H: 3.5 x 1.7 x 1.8 m Built in 1963 Weight approx. 650 kg The machine is in good condition, ready for operation. Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Drum motors for conveyor belt drives according to the list in photo The motors are in good condition, ready for operation Flat rate for all engines EUR 3800.00 Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Electrically heated continuous furnace, make VEI-Engineering type: DLNTO-EB 830-500 heat treatment: tempering temperature max. 500°C working temperature: 220-450°C clear dimensions (w x h): 800 x 210 mm heated length: 4.950 mm heating power: 2 x 30 kW fans: 2 x 5,5 kW Cooling water for 2 heat exchangers: inlet max. 2 bar PLC: Siemens S7

Mix tank Volume : 3000 L Mixing : High Shear Motor : 14 HP Mnufacture date : 2012 Condition : Never Used Heated : Hot water 90c Cooled : Cold water

AVIAN Engineering Model G46/ 60 Pinch Infeed Rollers Integral Blower Main Motor 20 kW Blower Motor 2 kW Rotary Blade 6pcs Stationary Blade 4pcs ThruPut 300 KG/H Cutting Chamber 620 x 460mm Hopper Opening 620 x 500mm

Kneading machine Kemper SPL 75 - 100 litres Masch. No. 672500 Strong and robust kneading machine in very good and well-maintained condition. Kneading machine from bakery.- 2 speeds- front and return pulse function timer no longer runs out- Operating hours: see photosPallet size, weight approx. 500kg (note when picking up) The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Painting drying plant Giardina Forno Statico MOS 3D Masch. No. 050354 Built in 2006 User manual available This plant is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

2 nos. GE PG9171E 180MW / 50 Hz gas fired combine cycle gas turbine power plant, year 2004, around 31,000 hr - 34,300 hr, Steam turbine is 60MW each , and complete with heat recovery boiler. Welcome enquiry for buying only 1 or 2 gas turbine or includes engineering works.

Electrically heated box furnace, make VEI-Engineering type: LU temperature: max. 650°C heating power: 45 kW fan: 3,0 kW total connected load: approx. 52 kVA internal dimensions (l x w x h): 1.000 x 700 x 700 mm charge weight: max. 1,0 t

Table crosscut saw Irion UKS 800 DS Masch. No. 1360 Stop left 7 m Stop right 3.5 m Feeder Roller conveyor 400 mm wide Roll 300 mm long with programming control with documentation with data storage L x W x H Machine: 1650 x 1650 x 1750 mm Built in 1994 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4952 Eriswil/EN-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Mill mat 4 CH-4952 Eriswil/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Pendulum circular saw Irion Cutting width 350 mm Roller table 3000 mm L x W x H: 600 x 500 x 1800 mm Weight approx. 250 kg Built in 1978 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Chain stemmer GF with drilling unit for wall mounting L x W x H: 1200 x 800 x 2300 mm Built in 1972 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Glue stand hydraulic, double-sided Format L x W: 3000 x 2000 mm L x W x H: 3200 x 2200 x 1100 mm Weight approx. 600 kg Built in 2003 Pressure per cylinder 2500 kg 8 clamping elements 2 Holders The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Table belt grinding machine Hunziker L x W x H: 3.5 x 1.7 x 1.7 m The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

bore capacity in steel (diameter): 75 mm arm length: 1700 mm workpiece height max.: 370 - 1700 mm total power requirement: 12 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m C S E P E L (Hungary) Radial Drill Model RFh 75/2000 Year 1977 Serial No. 61158 _______________________________________________________ Drilling capacity, Steel / Cast Iron, max. 75 / 90 mm Thread cutting Steel / Cast Iron M 60 / 70 Distance between column and spindle centre, max. 1,700 mm Spindle taper ( Morse Cone) MK 5 Vertical stroke of radial arm 380 mm 21 Spindle speeds 19 – 1.900 rpm Base plate 1.100 x 2.300 mm Mounting height, min./max. (base plate) 370 / 1,700 mm Swivelling radius +/- 180 ° Vertical adjustment of radial a ...

Veneer press Leopida Format: 2300 x 1000 mm Plates with hot water heating L x W x H: 2300 x 1100 x 2000 mm Weight approx. 2000 kg Built in 1978 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Table circular saw Schelling SKR with SUVA protection with stop Bösch L x W x H: 2200 x 1800 x 1100 mm Weight approx. 750 kg Built in 1973 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Edge flush milling machine JKO LT 750 with feed-in apparatus Masch. No. 1666 L x W x H: 1100 x 1000 x 1500 mm Built in 1966 Weight approx. 520 kg The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12