gear shaving used for sale

- Toothed gear MWM 12307524 - Please note! Price per piece! - 12307524 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new technologies and processes into  ...

Planing comb to Maag gear planing machine

Circulation cutter from Klingelberg

Max. wheel diameter : 300 mm Gear width : 180 mm Max. module : 5 Min. module : 0,5 Max. table load : 50 kg Number of teeth : 7-256 Max. helix angle : +/-45° Max. diameter of grinding wheel : 350 mm Turning speeds : 1100-1900 U/min

Gear motor Lenze Flange gear motor, shaft diameter 25 mm Wavelength 50 mm 1.5 kW Reduction 20.04 Output speed 172.1 In good condition, ready for use Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 fax 0041 62 966 21 12

Max. wheel diameter : 300 mm Gear width : 180 mm Max. module : 5 Min. module : 0,5 Max. table load : 50 kg Number of teeth : 7-256 Max. helix angle : +/-45° Max. diameter of grinding wheel : 350 mm Turning speeds : 1100-1900 U/min

Machine in good technical condition, possibility of testing after agreement. Machine weight 2000kg.

Code 151301 DESCRIPTION Gear Hobber Ø 250 x modul 6 Make Modul Model ZFWZ 250/3 Serial number 112 625 Year ± 1983 Ma. Workpiece diameter 250 mm Max. modul 6 Max. axialmovement 275 mm Max. tangential movement 100 mm Max. gearangle setting 45 degrees Max. diam. millingcutter 145 mm Max. millingcutter length 170 mm Diameter clampingtable 275 mm Diameter tablcenter positioning 200 mm Distance millingcutter to clampingsurface min/max. 195 – 470 mm Distance middle millingcutter to center table 20 – 230 mm Millingspeeds in steples in 2 Ranges 20 – 200 rpm 125 – 400 rpm Feeds axial 0.2 – 100 mm/wheel/rounds radial 0.025 – 4 mm/wheel/rounds tangential 0.1 – 5 mm/wheel/rounds Power main motor 7.5 kW – 380 Volts Power connection 22 kVA Accessories Chipconveyor All speedchang ...

Magnet agitator 0,55 kW gear motor,141 rpm,220/380 V.,Ø 300/600 stainless mixing blade.

Gear pump,stainless,acid proof steel,ECO GM4,0,25 kW,theoretical capacity 400 l/h.

Gear pump,stainless,acid proof steel,ECO,Pulsafed GM8,1,1 kW,Theo. cap. 2500 l/h.

Gear Pump,stainless steel,ECO GM8,1,5 kW,710 rpm.,Theo. cap 1900 l/h

Description mold control unit: 5 zones microcontroller: AT Output voltage: 230V temperature range: 60° - 450° C

Description Mold controller: 8 zones Microcontrollers: S - Line Output voltage: 230 V Temperature range: 0 - 500 °C With thermocouple and resistance cables of 3 meters.

Description control unit for molds: 5 zones microcontroller: jcs 400 output voltage: 230V temperature range: 50°-400° C WITHOUT CABLES

Description control unit for molds: 2 zones microcontroller: incatronic AL1 1500W output voltage: 230V temperature range: 0 ° -400 ° C

max. wheel diameter: 80 mm gear width: 120 mm max. module: 3 min. module: 1 control: SIEMENS 840 C total power requirement: 30 kW weight of the machine ca.: 7500 t dimensions of the machine ca.: m L I E B H E R R CNC – Controlled Gear Hobbing Machine Type LC 82 Baujahr 1995 Ser.-Nr. 0836 ______________________________________________________ Gear-Diam. max. 80 mm Module Range 1 - 3 Helix Angle +/- 45 ° Distance Table Center to Tool Center 15 – 160 mm Hobbing Head Slide stroke vertical 250 mm Tangential Travel / Shift Travel of Tool slide 180 mm Minimum Number of Teeth 3 (!) Hob Size max. Ø x length approx. 90 - 200 mm Taper of Hob spindle HSK 50 A Workpiece Clamping length (table/Tailstock) 250 mm Infeed rate ...

Description control unit for molds: 5 zones microcontroller: Temp Master III output voltage: 230V / 24V temperature range: 0-599 C

Description Control unit for molds: 56 zones Microcontroller: TH-SYNC output voltage: 230V temperature range: 0-400 ° C Without thermocouple cables and resistors

Description Control unit for molds: 76 zones Microcontroller: TH-SYNC output voltage: 230V temperature range: 0-400 ° C Without thermocouple cables and resistors

Description Mold Control Unit: 1 zone microcontroller: RTC - 550 output voltage: 230 V temperature range: 0-400 ° C

Description control unit 4 zones

workpiece diameter: 125 mm module: 4 Control: SIEMENS 840 C x-axis: 105 mm y-axis: 40 mm z-axis: 500 mm total power requirement: 47 kVA weight of the machine ca.: 5,5 t dimensions of the machine ca.: 2,6x2,1x3,1 m with measuring and palletizing system from Hörzer & Fehrenbach for gearwheels (bore receiver) Workpiece diameter: 17-39.5 mm Component height: approx. 6-15 mm Oblique as well as straight toothed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 3000 mm gear width: 1200 mm max. module: 30/40 min. module: 2 table diameter: 2500 mm table load capacity: 400 kN hob dia. - max.: 450 x 500 mm milling spindle speeds: 10 - 165 U/min hob length max.: 500 mm tip circle diameter: 2050 mm tooth helical angle min/max: 0 - 45 ° center distance betw. workpiece-tool min/max.: 150 - 1750 mm milling slide swivelling: 50 Grad distance table / counter stay: 1050 - 2050 mm shifting: 300 mm workpiece weight: 40 t table bore diameter: 800 mm depth of hole: 1100 mm main drive motor: 37 kW min. workpiece diameter: 290 mm min. number of teeth: Wälzfräsen 20 min. number of teeth: Formfräsen 2 taper: MK 100 feeds axial: 1 - 1800 mm/min radial feed: 1 - 500 mm/min feed: Tangential 1 - 450 mm/min rapid traverse: 1875 / 530 / 470 mm/min electrics - voltage/frequency: 380 / 50 V/Hz control: Siemens Sinumerik 3M total power requirement: ...

workpiece diameter: 250 mm centre distance: 0 mm honing length max.: mm max. module: 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. All roughing and finishing infeeds can be adjusted by a decade switch ...

max. wheel diameter: 400 mm gear width: 0 mm module: pinion diameter - max.: 254 mm axial cross angle: 90 ° total power requirement: 15 kW weight of the machine ca.: t dimensions of the machine ca.: m This machine is very suitable for precision production testing of spiral and hypoid bevel gears with shaft angle 90°. The gear spindle is vertical and the pinion spindle is horizontal. The pinion cone distance can be adjusted while the machine is working in order to find the optimal mounting position whereby the gear is loaded with a preset torque. The axial pinion position can be adjusted until the quietest meshing position of the traction flank is found. Likewise, the thrust flank can be tested during the return run. Marking compound is sprayed on both sides of the teeth so the flank contact pattern can be seen. Working cycles, as well as the positioning in the tooth gap, are automat ...

max. wheel diameter: 2500 mm gear width: 0 mm max. module: 34 min. module: 1 total power requirement: ca. 15 kW weight of the machine ca.: 15 t dimensions of the machine ca.: 4,20 x 2,00 x 2,90 m Extra große ZR-Prüfmaschine, Gegenhalter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 400 mm gear width: 280 mm max. module: 1 min. module: 4 total power requirement: 15 kW weight of the machine ca.: 6000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 400 mm gear width: 75 mm max. module: 0,5 min. module: 6 total power requirement: 25 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 1800 mm gear width: 735 mm max. module: 12 min. module: 1 total power requirement: 30 kW weight of the machine ca.: 23 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 0 mm gear width: 150 mm max. module: 2,5 min. module: total power requirement: 10 kW weight of the machine ca.: 2400 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 400 mm gear width: NA mm max. module: 5 min. module: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Manual Two Flank Gear Tester The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 120 mm gear width: 160 mm max. module: 3 min. module: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Two Flank Gear Tester The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 80 mm gear width: 150 mm max. module: 2,5 min. module: total power requirement: 10 kW weight of the machine ca.: 2400 kg M I K R O N (Switzerland) Fully Automatic Gear Hobber for Worm Gears Model A 33 / 1 Year 1985 Ser.-No. 14.06/14.07/14.15 ____________________________________________________________ max. gear- without feed magazine approx. 80 mm max. gear- with feed magazine approx. 50 mm Module max. 2, / 2,5 Axial milling length approx. 150 mm max. workpiece-mounting length approx. 200 mm Milling slide can be swivelled up to 90 degrees Milling cutter - 24 - 50/63 mm Max. radial distance of milling slide 0-14/18 mm Milling cutter adjustment max. 25 mm Milling cutter speed 212 - 2.000 rpm Axial feed range infinitely adjustable 0,05 - 4,0 mm/workpiece rotation radial infinitely adjustable 0,2 - 200 mm/min.  ...

max. wheel diameter: NA mm gear width: NA mm max. module: min. module: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Manually operated 2-Flank Gear Tester The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter:30-150 mm max. module:6 total power requirement:36 kW weight of the machine ca.:11 t dimensions of the machine ca.:2,4 x 2,5 x 3,4 m

max. wheel diameter: 2000 mm gear width: 0 mm max. module: 0 dimensions of the machine ca.: 2x1,2x1,5 m uncomplete machine body with drive motor. drive unit fully functional. Without grinding unit. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

weight of the machine ca.:4 t

max. wheel diameter:600 mm max. module:10 min. module:2 total power requirement:1,4 kW weight of the machine ca.:0,68 t dimensions of the machine ca.:1,6x0,75 m diameter of hob:15 mm gear width:140 mm

max. wheel diameter:180 mm gear width: mm max. module:4 total power requirement:14 kW weight of the machine ca.:8 t slide travel axial ( Z-axis ):300 mm work piece - max.:490-640 mm

max. wheel diameter:275 mm gear width:58 mm max. module:8 min. module:0,5 weight of the machine ca.:10 t max. number of teeth:200 min. number of teeth:5

max. wheel diameter:275 mm gear width:58 mm max. module:8 min. module:0,5 weight of the machine ca.:10 t max. number of teeth:200 min. number of teeth:5

max. wheel diameter: 650 mm gear width: 200 mm max. module: 10 min. module: 1 work accuracy: DIN 6 clamping table diameter: 710 mm table bore diameter: 150 mm number of strokes - stepless: 35,5 - 560 c/min max. ram stroke: 230 mm feeds: 3,55 - 40 mm/min radial feed: 0,8 - 9 mm/min work-spindle diameter: 110 mm total power requirement: 28,2 kW weight of the machine ca.: 9 t dimensions of the machine ca.: 3,8 x 2,3 x 2,5 m Gear shaping machine for the production of spur gears, for Internal and external gears - Built under licence from LORENZ and identical in construction to LORENZ LS 630 complete Modernisation + overhaul in 2012 with: - new painting - new electrical system from Telemecanique - Counter Holder - Chip conveyor - Coolant unit - change gears Not used in production again after overhaul The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

control:siemens 1P 6SL 3054--0CE01-1AA0 Documents:vorhanden

max. wheel diameter:180 mm

max. wheel diameter:180 mm

max. wheel diameter: 400 mm gear width: 200 mm max. module: 10 min. module: 1 profile depth: 25 mm x-axis: 630 mm y-axis: 400 mm z-axis: 190 mm U-axis: 80 mm a- axis: 360 ° b-axis: +/- 30 ° max.helical angle: 30 ° grinding wheel diameter: 250 - 350 mm spindle speeds (infinitely variable): 1500 - 2800 U/min grinding slide feeds: 6000 mm/min center distance betw. workpiece-tool min/max.: pitch max.: 9000 mm pitch min.: 10 mm electrics - voltage/frequency: 380 / 50 V/Hz total power requirement: 38 kW weight of the machine ca.: 9,5 t dimensions of the machine ca.: 4,2 x 2,6 x 2,8 m horizontal Profil Gear Grinding Machine for Spur and Helical External Gears. Machine can be used with Abrasive Electrocorundum Wheels or with CBN or Elbor Wheels. Equipped with: - CNC Control FANUC 0i-MF -- for 6 Controlled Axis (4 simultaneously) - Gear Measuring System - Chip and Sludge Removal System - Pape ...