rep 고무 기계 사용 판매를 위해

REP model V68 Y20W vertical rubber injection presses, Type G8, year 2003, Clamp force 4000kN, Platen size: 630 x 800mm, Distance between columns: 730/440mm, Daylight: approx 1000mm, Injection unit type Y2000, Piston dia 81.5mm, Shot capacity: 2000cm3, Injection pressure: 1500 Bar Top and bottom ejectors. O/a dimensions: 2950mm x 1410mm x 4800mm high, weight approx 12000kgs. Complete and in very good condition (not operated for over 2 years).

REP H48Y10W Horizontal Injection Moulding Machine Year of construction 2005 Machine Parameters Volume [cm3] 1000 Clamping force [kN] 1930 Injection pressure [bar] 1500 Moulds dimension [mm] 450x450 Tonnage 1.9t Platen size: 450x450 Cycles: 2,220,383 General condition: operational Dims [mm]: 4200 L x 1400 W x 2200 H Weight [kg]: 6750

clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 300 x 300 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 300 x 300 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 76A fuse protection (incl. peripherals) - Pump output: 7.5 kW, 14.9 A - Total output: 28 kW Dimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mm Weight approx.: 2,250 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

REP Press Model V58Y10W Injection volume 1000ccm Platen size: 500 x 630 mm Year 2006 Power: 2550 kN Operating hours: 14570 Moveable traverse Fix traverse Sliding Table

clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 600 x 400 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 90A fuse protection Approx. dimensions: 1,550 x 1,050 x 3,120 mm Weight approx.: 2,250 kg Two identical systems are available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 550 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand, Modell TTV-C40-125 C40P01B clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 550 x 400 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 90A fuse protection Approx. dimensions: 1,550 x 1,050 x 3,120 mm Weight approx.: 3,200 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Rep M46 Injection Moulding Machine Size of platens 430x430mm Injection unit short volume 670cm3 Injection pressure 1690 bar Injection force 331kN

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

1 x Repiquet 2550mm wide x 820mm dia 4 roll inverted L Calender, Machine type: CALANDRE 4 CYL DE 820 x 2550, Machine no. 70-C9-87 Motorised nip adjustment, Peripherally drilled rolls, High pressure hot water hearing Bush bearings with flood lubrication, Hydraulic pre-loading to all rolls, Roll bending and unbending on roll 4, Cross axis on roll 3 and 1. Automatic bank sensors/control + camera system Traversing unit for roll buffing or sand blasting. 'Citroen' unidrive gearbox, type: SPECIAL, order no. 50491, Power 140/240 C.V. Speed 1500/2250, Output 46/59 with individual motor to each roll- Roll 1 and 4 - 130HP, Roll 2 and 3 - 240HP, Max calender speed 120m/min. Dual embossing station with approx 25 x embossing rolls (+ 5 x rubber pressure rollers) In very good condition.

We are selling a large-capacity 3D printer X1000 from German RepRap GmbH. The device is in good condition and has been serviced by Innovatiq., Scope of delivery:, - 1 pc. 3D printer X1000, - Small parts and remaining consumables, Installation space in mm (x/y/z): 1000 x 800 x 600 mm, build speed: 10 – 150 mm/s, Travel speed: 10 – 300mm/s, Layer thickness: 0.02mm, Filament diameter: 1,75 mm, Nozzle diameter: 0.4mm / 0.6mm / 0.8mm, extruder units: DD3 Dual, Extruder temperature: max.290°C, Print bed technology: Heatable up to 120°C, Data transfer/network: LC touch display, wireless printing via WLAN, Ethernet, software: Simplify3D Software, Power consumption: (max.) 2.5kW, approx. 30% in continuous operation, Power connection: Three-phase current 400V (CEE 3L+N+PE), 16 A, Dimensions in mm (w x h x d): 1725 x 1500 x 1320 mm, Weight in kg: 400 kg