paal 프레스 사용 판매를 위해

automatic baler Manufacturer: PAAL Type: KONTI 275 D/k Year of construction 1999 specifications: Pressing force: 75 t Specific pressing force: 9.09 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 500 - 750 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 75 kW Throughput: 350 m³/h Pressing capacity: - approx. 12.0 t/h at department store (35 kg/m³ bulk density) - approx. 21.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 33.0 t/h for collected goods (100 kg/m³ bulk density) Binding: 4-fold vertical + 3-fold horizontal Machine weight: approx. 25.0 t

New hydraulic pump QX61-250/63-100R88 for PAAL channel baler. Can be used in systems with a 75kW motor.

automatic baler Manufacturer: PAAL Type: PACOMAT IS Year of construction: 1988 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Channel size: 700 x 700 mm Opening: 800 x 650 mm Drive power: 22 kW Throughput: 100 m³/h with additional manual hopper Wire flow in the pressing direction seen on the left side

Brand new gear pump, with internal gearing for PAAL Konti, Pacomat channel baling press. Can be used in systems with a motor of at least 22 kW

Dual hydraulic pump for PAAL, 45kW Used 2-piece hydraulic pump for PAAL channel baling press. Can be used in systems with a 45 kW motor

automatic baler Manufacturer: PAAL Type: KONTI 275 C Year of construction 1996 specifications: Press force: 65 t Specific pressing force: 7.88 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 450 - 600 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 45 + 30 kW Throughput: 380 m³/h Pressing capacity: - approx. 13.0 t/h at department store (35 kg/m³ bulk density) - approx. 23.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 35.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 21.0 t Optionally with feeding belt according to photos

automatic baler Manufacturer: PAAL Type PACOMAT II S SO Year of construction: 1994 specifications: Pressing force: 50 t Specific pressing force: 7.14 kg/cm² Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm Drive power: 45 kW Throughput: approx. 170 m³/h automatic 4-fold horizontal binding

Used Triple Hydraulic Pump QX51-125/53-063/52-063R91 for PAAL channel baler. Can be used in systems with a 45 kW or 55 kW motor. Manufacturer partnumber: QX51-125/53-063/52-063R91

used box press Manufacturer: PAAL Type: HS 34 specifications: Filling box size: 1,000 x 700 x 2,200 mm (W x D x L) Filling opening: - 1st filling: 2,200 x 1,000 mm - 2nd filling: 1,200 x 1,000 mm Press pressure: approx. 18 t Drive power: 4 kW Lifting speed pre-pressing and retraction: 2.5 m/min. Lifting speed repressing: 1.25 m/min. Bale size: approx. 700 x 1,000 x 1,300 mm Bale weight: up to approx. 300 kg Weight of the machine: approx. 2000 kg Machine dimensions: 3,500 x 1950 x 1,450 mm (L x W x H)

Baler Paal Pacomat II with hopper, built in 1979 Specifications: Manufacturer: Paal Type: Pacomat II Year of Make: 1979 Drive power: 11 kW Pressing force: 27 t Channel cross-section: 700 x 1000 mm Filling opening: 1000 x 650 mm Flow rate: approx. 60/115 m³/h Bale size: 700 x 1000 mm Bale weight: up to 400 kg Machine dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine weight: approx. 5200 kg Materials: paper, cardboard, foil Remarks: The machine is in working condition. It was inspected and tested by us in 28816 Stuhr. You can find the video on our website or our Youtube channel. Viewings, also under power, are possible at any time by arrangement. On request, we also carry out tests with your material for an expense allowance. We will also be happy to answer any questions you may have about the machine by phone from Monday to Thursday from 08.00 to 14.00 ...

automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 Machine was only in operation for 4 years specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 42 t Attached pictures are only sample pictures!

used baler Manufacturer: PAAL Type: LIKON 110/150 Year of construction: May 2004 Specifications: Press weight up to: approx. 36 tons Press force at 275 bar: 150 t Operating pressure max. 320 bar Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 2 x 75 kW Flow rate: 425 m³/h Binding: 5-fold horizontal Total connected load: 176 kW Rated current: 340 A Pre-fuse (min.) 400 A Operating voltage: 3 x 400 VAC/50 Hz/N/PE Control voltage: 230 VAC / 24 VDC including: - Oil cooling - Low-pressure circuit - Free kicks - Key locking system Transport dimensions: Length: 13,803 mm Width: 2,500 mm Height: 3,164 mm without wire unwinding devices, without binding wire, without feed belt, without a personal protection system, without conveyor belt hopper and withou ...

automatic baler Manufacturer: PAAL Type: KONTI 700 G/S Year of construction 2010 specifications: Press force: 1940 kN/ 198 t at 300 bar Specific pressing force: 160 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 75 kW Throughput capacity (according to manufacturer's specifications): approx. 650 m³/h Capacity at 35 kg/m³: 22.5 t/h Capacity at 60 kg/m³: 36.5 t/h Capacity at 100 kg/m³: 55.5 t/h Binding: 5-fold vertical Bale weight: approx. 800 - 1,450 kg depending on baled material and bale length Machine weight: up to approx. 47 t

Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance

automatic baler Manafacture: PAAL Type: PACOMAT IS Year of construction: 1993 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Duct format: 700 x 700 mm Filling opening: 800 x 650 mm Drive power: 18.5 kW Throughput: 80 m³/h with additional manual feed hopper Wire passage seen in the direction of pressing on the left side

automatic baler Manufacturer: PAAL Type: KONTI 600 G/S/K with cross-binding Year of construction 2012 Operating hours: approx. 44,700 hours specifications: Press force: 1,546 kN System pressure: 315 bar Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 55 kW Pump capacity: 3 x 420 Ltr. Oil tank volume: 3,100 ltr. Throughput:approx. 780 m³/h Capacity at idle: approx. 1,220 m³/h Capacity at 35 kg/m³: approx. 26.5 t/h Output at 60 kg/m³: approx. 44.0 t/h Output at 100 kg/m³: approx. 69.0 t/h Control: Siemens S7 Setting: 5-fold vertical Additional 4-fold automatic horizontal tying Bale weight: approx. 800 - 1,250 kg depending on the material to be pressed and bale length Machine weight: up to approx. 42 t Includes a top pressure plate slot cover Printing plate was renewe ...

Baler Paal Konti 200 D, built in 2000, optionally with matching conveyor belt Paal KEM-1400 Technical data: Manufacturer: Paal Type Paal Konti 200 D Year of construction 2000 Hours: 28155 Pressing force 60 t Drive power 45 kW Total connection 60 kW Filling opening 1020 x 1400 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying throughput at 35 kg/m³ approx. 9.5 t/h 60 kg/m³ approx. 16.5 t/h 100 kg/m³ approx. 26 t/h Bale weight 450 to 650 kg Transport dimensions approx. 10123 x 2152 x 2720 mm (LxWxH) Machine weight approx. 15,000 kg Materials: paper, cardboard, foil The press is in good condition and has been inspected and tested. You can find a video on our website or YouTube channel. The complete documentation is available. Please note: All technical data refer to the manufacturer's specifications. We a ...

automatic baler Manufacturer: PAAL Type: KONTI 700 G/S Year of construction 2010 Technical data: Press force: 1940 kN/ 198 t at 300 bar Specific pressing force: 160 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 75 kW Throughput capacity (according to manufacturer's specifications): approx. 650 m³/h Capacity at 35 kg/m³: 22.5 t/h Capacity at 60 kg/m³: 36.5 t/h Capacity at 100 kg/m³: 55.5 t/h Binding: 5-fold vertical Bale weight: approx. 800 - 1,450 kg depending on baled material and bale length Machine weight: up to approx. 47 t Optional: with Bollegraaf steel plate strip according to picture

Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic

automatic baler Manufacturer: PAAL Type: KONTI 200 C Year of construction: 1993 specifications: Press force: 50 t Channel format: 750 x 1,100 mm Specific pressing force: 6.06 kg/cm² Bale weight: 425 - 550 kg, depending on material and bale length Infill opening: 1,400 x 1,020 mm Drive power: 45 kW Throughput: 200 m³/h Pressing capacity: - approx. 7.35 t/h layered at department store (35 kg/m³ bulk density) - approx. 12.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 20.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 17 t

LIKON 200C Horizontal Baler Machine Technical specifications: Engine power - 22 kW Year of production - 1994 With oil cooler Horizontal binding x 4 times Press force - 30 t Overall dimensions of the baler: 10000 x 2000 x 2750 mm Press weight: 10 t Loading opening dimensions: 1400 x 700 mm Bundle dimensions - 700 x 1100 x 1000-1200 mm, variable length With hydraulic oil No binding wire It worked in a printing shop without a conveyor belt, only with dry-shredded printing waste! Motorcycle hours - 62639 The baler is in good condition, ready for operation PRICE ON REQUEST! ----- Horizontal Baller Paal LIKON 200C Technische Daten: Motorleistung - 22 kW Produktionsjahr - 1994. Mit Ölkühler Horizontale Bindung x 4 Mal Presskraft - 30 t Gesamtabmessungen der Presse: 10000x2000x2750 mm Eigengewicht der ...

automatic baler Manufacturer: PAAL Type: KONTI 125 Year of Make: 1988 Operating hours: approx. 23660 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Binding: 3-fold vertical Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: approx. 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)

used baler Manufacturer: PAAL Type: PACOMAT I-35 Year of Make: 2008 specifications: Press force: 35 t Specific pressing force: 7.14 kg/cm² Drive power: 22 kW Throughput: up to approx. 85 m³/h under operating conditions Channel format: 700 x 700 mm Filling opening: 800 x 620 mm Machine weight: up to approx. 6.5 t (depending on equipment)

Fully automatic baler Manufacturer: PAAL Type KONTI 275 D Year of Make: 2000 specifications: Press force: 75 t Drive power: 1 x 45 kW Total connected load: kW __ / 170 A Throughput under operating conditions: 280 m³/h Filling opening: 1,020 x 1,550 mm Bale size:750 x 1,100 mm Binding: 4-fold vertical incl. front printing plate slot cover Machine weight: approx. 25 t Bale weights: up to approx. 600 kg Including: - Free kicks - Large digit display

Specifications Maximum pressure: 75 tons Year of Make: 1999 Press force: 90.9 t/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1550 mm Bale weight: 500-750 kg Weight: approx. 25 tons Power connection: 400 V Bale tying: automatic Motor: 75 kW (possibility of switching to 55 or 45 kW) Press capacity at idle: max 750 m³ / hour Press capacity under operating conditions: max 350 m³ / hour Theoretical throughput to density 35 kg/m3: approx. 12 tons/hour Theoretical throughput to density 60 kg/m3: approx. 21 tons/hour Theoretical throughput to density 100 kg/m3: approx. 33 tons/hour Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Cho ...

used baler Herateller: PAAL Type: PACOMAT II Year of Make: 1995 Specifications: Pressing force: 27 t Drive power: 18.5 kW Total connected load: 25 kW Throughput: 115 m³/h Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm (H x W)

automatic baler Manufacturer: PAAL Type: Pacomat IS Year of Make: 1990 specifications: Pressing force: 27 t Specific pressing force: 5.51 kg/cm² Total connected load: 23 kW Rated current: 46 A Main drive power: 18.5 kW Capacity: 80 m³/h Control: Siemens S5 100 U Bale size: 700 x 700 Filling opening: 800 x 600 mm

automatic baler Manufacturer: PAAL Type: KONTI 125 SO Year of Make: 1990 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)

automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 only 4 years in operation specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 39 t

Technical data: Maximum pressure: 60 tons Year of Make: 1999 Press force: 72.7 t/cm² Number of Bindings: 4 Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1400 mm Bale weight: 450-650 kg Weight: approx. 20 tons Power connection: 400 V/ 45 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance If you have any further questions about this or similar channel balers, please do not hesitate to contact us by email or phone!

Manufacturer: Paal Model : Konti 275 G Year of Manufacture : 2010 Find more here - / Contact us at -

Maximum pressure: 50 tons Year of Make: 2006 Pressing force: 65 tons/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1000 mm Dimensions of the tailgate: 920 x 1400 mm Bale weight: 350-500 kg Weight: approx. 13 tons Power connection: 400 V/ 22 kW Bale tying: automatic

Baler Paal Konti 325 D/SO, built in 1999 Technical data: Manufacturer: Paal Type Paal Konti 325 D/SO Built in 1999 Hours: 50702 Press force 94 t Drive power: 2 x 45 kW Total connection 104 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying Throughput at 35 kg/m³ approx. 14 t/h 60 kg/m³ approx. 24 t/h 100 kg/m³ approx. 38 t/h Bale weight 525 to 800 kg Transport dimensions approx. 12352 x 2340 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment is made ex wor ...

BALLER PAAL KONTI 425 C Technical specifications: Manufacturer: Paal Type: Konti 425C Year of manufacture: 1995 Klsdm Ajx Dk Ttsty Atel Feed opening: 102 x 175 cm Drive power: 170 kW Caedm Atyexx Su Uo Atsa Compression force: 85 t Settings: Horizontal, fully automatic Roll weight: 500-650 kg Press weight: 25 t PRICE ON REQUEST! ----- BALLER PAAL KONTI 425 C Technische Daten: Hersteller: Paal Typ: Konti 425C Herstellungsjahr: 1995 Bwsbjycfuqsmcbw Nveh Einfüllöffnung: 102 x 175 cm Antriebsleistung: 170 kW Kompressionskraft: 85 t Einstellungen: Horizontal, Vollautomatisch Rollengewicht: 500-650 kg Pressgewicht: 25 t PREIS BEI ANFRAGE!

For sale: Paal Konti 425 D horizontal baler Technical specifications: Manufacturer: Paal Type: Konti 425D Year of manufacture: 2002 Feed opening: 102 x 200 cm Drive power: 2 x 45, 2 x 75 kW Kledex Dlanem Aty Atsl Pressing force: 115 t Settings: Horizontal, fully automatic Roll weight: 550-850 kg Pressing weight: 36 t PRICE ON REQUEST! ----- Verkaufen horizontal Baller Paal Konti 425 D Technische Daten: Hersteller: Paal Typ: Konti 425D Baujahr: 2002 Einfüllöffnung: 102 x 200 cm Antriebsleistung: 2 x 45, 2 x 75 kW Druckkraft: 115 t Einstellungen: Horizontal, Vollautomatisch Rollengewicht: 550-850 kg Pressgewicht: 36 t PREIS BEI ANFRAGE!

Just Arrived Baler Paal Konti 325 G, built in 2013 Technical data: Manufacturer: Paal Type Konti 325 G Year of construction 2013 Hours: 12110 Press force 100 t Drive power 2 x 55 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable Setting 5-fold automatic Throughput at 35 kg/m³ approx. 13.5 t/h 60 kg/m³ approx. 21.5 t/h 100 kg/m³ approx. 33 t/h Bale weight up to 800 kg Transport dimensions approx. 12216 x 2530 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment is made ex works, w ...

automatic baling press Manufacturer: PAAL Type: KONTI 275 F Built: 2007 Main parts of the press: 1 automatic duct press (without wire winding devices) 1 automatic lacing 1 Hydraulic system 1 Electric control technical data: Pressing force: 800 kN / 80 t at 300 bar Specific pressing force: 9.70 kg/cm2 Channel cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,600mm Number of connecting wires: 4 pieces vertically Drive power: Main pump: 1 x 45 kW Pump delivery capacity: 1 x 380 l/min Throughput: up to approx. 280 m3/h under operating conditions Performance at: - 35 kg/m3 bulk weight: approx. 9.5 t/h - 60 kg/m3 bulk weight: approx. 16.5 t/h - 100 kg/m3 bulk weight: approx. 26.0 t/h Hydraulic oil tank volume: 2,100 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Other equipment: Operator Panel MP 270 auto ...

used chain conveyor belt Manufacturer: PAAL Type: KEL 1000 Year of construction: 1997 specifications: Conveying width: approx. 1,000 mm Center distance:approx. 7,500 mm Band course: ascending over the entire length, Conveyor belt drive power: 3.0 kW Side bolster height: 500 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of construction: 2008 specifications: Conveyor width: approx. 1,500 mm Wheelbase:approx. 9,625 mm Strip course: approx. 2,935 mm horizontally underfloor, then rising to a length of approx. 4,500 mm below 28°, sloping below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE as far as possible pre-assembled, consisting of: - Strip scaffolding in solidly welded section steel and sheet steel edge construction, - additional sliding guides underneath the belt support profiles in the horizontal and climbing sections to support heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with 2 ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 1990 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 78 kW Rated current: 150 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press.  ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 1996 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 82 kW Rated current: 162 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press. T ...

Technical data Maximum pressure: 50 tons Year of Make: 1994 Pressing force: 7.14 kg/cm² Number of bindings: 3 horizontal Channel cross-section: 1000 x 700 mm Dimensions of the tailgate: 145 x 95 cm Bale weight: do 500 kg Weight: approx. 10 tons Power connection: 400 V/ 45 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers,  ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...

Manufacturer: PAAL Model: KONTI 700 G/S/K Year of Manufacture: 2011 Type of Machine :Baling Press Key Features - Cross-lacing system (optionally switchable) - Oil cooling system - CE marked Find more here - / Contact us at -

The BTS-Drum Crusher is ideal for compacting 30 to 220 Ltr drums / barrels, but also plastic and cardboard drums can be easily reduced to their minimum of volume. In many cases this compacted material can then even be marketed again. The drum press impresses with its ease of use, safe operation and high throughput quality. By crushing these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 24 Ton Machine size: 2587 H x 1190 W x 1000 D mm Machine weight: 690 kg Transport height: 1800 mm Compaction rate: 8:1 Cycle times: 40 seconds Motor: 11 kW 32 Amp Power supply: 380 - 400 V (3 phase) Noise level: 68 dB User-friendly lever control Compaction head with spikes to punch the drum to drain out any residual liqui ...

The BTS drum press PLC auto is ideal for compressing 30 to 220 litre steel drums, but it can also be used to compress plastic and cardboard drums very easily. In many cases this compressed recyclable material can then even be remarketed. The barrel press is particularly characterized by its reliable and easy operation. By compacting these waste/recyclable materials, you achieve a volume reduction of up to 90%, save significantly on your disposal costs and properly return the material to the recyclable material cycle. Pressing force: 24 tons Machine dimensions: 2587 H x 1190 W x 1000 D mm Machine weight: 690 kg Transport height: 1800 mm Compression: 8:1 Pressing time: 40 seconds Motor: 11 kW 32 Amp Power supply: 380 - 400 V (3 phases) Noise: 68 dB PLC control with automatic pressing cycle 30 litre drip pan with drain tap Pressing punch with mandrels for pi ...

sell a Strautmann PET BP 900 for PET bottles! Built in 2006, just a few hours of operation!

Barrel press RMH 200 Electric motor: 5.5 KW, 400 V, 50 Hz Pressure: 25 T Press cycle: 58 seconds W x D x H: 1200 x 1000 x 2800 mm

Automatic control: At the push of a button, the machine automatically closes the pre-loading box and the upper Lid (the pestle is extended). Then the front lid opens and the bale is ejected. Then the front lid (the upper one) closes The lid opens and the pestle goes back and the machine waits for another push of a button (filling the pre-load box). Metal press RMH 33 S_ 30 x 30 (new machine type: metal press) Manufacturer: RMH Type: RMH 33 Package dimensions in cm: 30 x 30 x material Package Weight: 30 - 50 kg Total weight: 5500 kg Dimensions Box (WxHxL): 30 x 50 x 100 cm Dimensions Machine (WxHxL): 120 x 85 x 410 cm / without preload box Cycle time: 60 seconds Drive: 30 KW Compression force: 60 T Horizontal ramming compression force: 100 T Working pressure: 300 bar Control: Automatic

Metal press RMH MB (Mini Baler) This machine is particularly suitable for pressing aluminium, copper, zinc and other metals. The RMH MB Mini Baler is able to crush and then press larger material made of aluminium, copper, zinc and other metals thanks to lateral knives on three sides of the filling box. Technical data: Drive: 7.5 Kw / 400 V Weight: 1.8 T Shear lid pressure: 20 t Ground ram pressure: 40 t Working pressure: 220 BAR Filling box dimensions (L x W x D): 81.5 cm x 35 cm x 51 cm Package dimensions (L x W x material quantity): 35 cm x 20 cm x variable length (material quantity) Pressing cycle: about 1 minute Dimensions (L x W x H): 2.45 meters x 1.20 meters x 1.40 meters CE Norm Metal Baler RMH MB (mini baler) Cutting edges on three sides of the bale box and lid give this machine the ability to handle with oversized materials out of aluminium, copper,  ...

The BTS-1100 Bin Compactor is ideal for material compacting in your 1100 Ltr. garbage and recycling wheelie bins. Large bulky rubbish, but also cardboard and recyclable materials can be compacted easily and safe to a minimum of its size. By compacting these waste and recyclable materials you achieve a volume reduction of up to 80%, a significant saving on your disposal costs and you also create a safe and clean working environment. Pressing force: 3.5 Ton Compaction: up to 80 % (material depending) Machine size: 2120 H x 1160 W x 1150 D mm Machine weight: 270 kg Transport height: 1594 mm Cycle times: 20 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly and safe two hand lever control Optimum utilization of garbage bins Reduces the number of waste bins No more climbing into wheelie bins Reduces frequency of  ...

We offer replacement and wear parts for all common scrap baling presses of German manufacturers, such as Lindemann, Becker & Prünte, Becker, Oberländer, Leimbach.

Multi-chamber press C400 | C600 | C800 C400 (with two pressing chambers) C600 (with three pressing chambers) C800 (with four pressing chambers) Specifications: Motor 1,5kW Electronic voltage 230V/50Hz/1-F. Maximum pressing force 6.5t Working pressure 150bar Cylinder stroke 700mm Time press cycle 50s Press chamber (LxWxH) 730x600x830mm Insertion height 1060mm Insertion opening (LxW) 730x600mm package size (LxWxH) 730x600x400mm Package weight 30-40kg Binding rolls 8x6x4x Strap type (polyester) 9mm/250m Number of containers 4x3x2x Length ges. 3455m; 2615mm; 1775mm; 17775mm Width ges. 1050mm Height ges. 1955mm Weight ges. 1955mm Weight ges. 1090kg; 880kg; 670kg; 510kg Transport dimensions C400 !x container Length 1680 mm 840 mm Width 845 mm 845 mm Height 1955 mm 1060 mm Weight ges. 210 kg Multi-chamber press C400 (with two pressing chambers) C600 ( ...

Baler, press for cardboard, film paper V5 | 5t Bale size: 700 mm H (variable) × 750 mm W × 500 mm D Bale weight: 50–100 kg Pressing time: 28 seconds Pressing force: up to 5 tons Dimensions: 2015 mm H × 870 mm W × 655 mm D Filling opening: 750 mm W × 385 mm H Integrated bale ejection mechanism Weight: 340 kg Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Noise: 70 decibels E-Power DIN EN 16500 IP54 protection class PLC with automatic cycle CE Certification V5 SMALL BALER Versatile, efficient and simple operation: The V5 baler is ideal for small and medium-sized companies. Even with a small amount of material, it creates order, cleanliness and space. The setting of the pressing cycle on the V5 can be done either automatically or manually. With the help of the "Easy Tie" system, the finished bale can be tied quickly and conveniently when the door is ope ...

Polystyrene compressor Styropactor MAXI | Shredder press for Polystyrene EPS Compressor, combination of shredder and press for polystyrene EPS MAXI Commodity number: 42055 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 70-90 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 100-120 Connection: 7.5kW, 3-phase 400V/50Hz 480V/60Hz Insertion opening: 600×1000 mm Length: 3180 mm Height: 1600 mm Width: 870 mm MAXI PLUS Commodity number: 42060 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 110-130 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 170-200 boxes/h Connection: 11kW, 3-phase 400V/50Hz, 480V/60Hz Insertion opening: 600×1000 mm Length: 3680 mm Height: 1600 mm Width: 870 mm Wet boxes: YES Stainless stee ...

Baler V8 | 8t pressing force. Press for cardboard, foil, paper. V8 MEDIUM-SIZED BALER Our V8 baler is versatile and offers medium-sized companies that need to process a range of materials, including bulky objects and packages of different sizes, with excellent value for money. The V8 produces bales that fit perfectly on a Euro pallet and is suitable for pressing cardboard, plastic, textiles, paper, polystyrene and food waste Recommended for supermarkets, gas stations, department stores, hotels, factories and logistics centers. Bale size: 800 mm H × 950 mm W × 600 mm D Bale weight: 100–180 kg Pressing time: 33 seconds Pressing force: up to 8 tons Dimensions: 2270 mm H × 1100 mm W × 745 mm D Filling opening: 950 mm W × 485 Integrated bale ejection mechanism Weight: 425 kg Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Noise: 70 decibels E-Power DIN EN  ...

Baler V20X | 20t press for cardboard, foil, paper, waste Baler, packaging press V20X | 006 With a pressing force of up to 25 tons, the V20X can efficiently compact cardboard, plastic, paper, textiles and food waste. Recommended for markets, department stores, hotels and all other users who have to deal with average amounts of waste and have to work at low ceiling heights. Bale size: 800 mm H (variable) × 1100 mm W × 750 mm D Bale weight: 200–300 kg Pressing time: 35 seconds Pressing force: up to 25 tons Dimensions: 1970 mm H × 1695 mm W × 865 mm D Filling opening: 1100 mm W × 625 mm H Integrated bale ejection mechanism Weight: 980 kg Power supply: Three-phase, 380/400 volt 3 kW motor Noise: 74 decibels DIN EN 16500 IP54 protection class E-Power Standards PLC light indicator "Bale full" and "Automatic pressing process"

Baler, press for cardboard cardboard, foil paper V50 | 706 SPECIFICATIONS Bale size: 1000 mm H (variable) × 1200 mm B × 800 mm D Bale weight: 350–550 kg Pressing time: 45 seconds Pressing force: up to 50 tons Dimensions: 3055 mm H × 1985 mm W × 1130 mm D Filling opening: 1200 mm W × 640 mm H Weight: 1870 kg Power supply: Three-phase, 380/400 volt 7.5 kW motor Noise: 74 decibels DIN EN 16500 IP 54 protection class PLC light indicator "Bale full" and "Automatic pressing process" CE Certification Made in EU OPTIONS Adaptable for vehicle bodies Suitable for use at sea Automatically opening guillotine door E-Power (three-phase motor with 380/440 volts and 4 kW) PET Press Filling at the back of the machine Electronic weighing system Annual maintenance contract Galvanized Description The V50 is perfect for pressing large volumes of waste and then reselling or ...

Bale size: 600 mm H (variable) × 600 mm W × 400 mm D Bale weight: 15–30 kg Pressing time: 35 seconds Pressing force: up to 8 tons Dimensions: 2500 mm H × 765 mm W × 575 mm D Integrated bale ejection mechanism Hinged door Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Weight: 415 kg Noise: 70 decibels DIN EN 16500 IP54 protection class PLC with automatic cycle CE Certification Made in EU OPTIONS Collecting tray for residual liquid Suitable for use at sea Electronic weighing system Annual maintenance contract Solar powered Galvanized or stainless steel V5HD PRESS FOR CANS & BOTTLES Fast, efficient and easy to use: The V5HD effortlessly presses aluminium cans and PET bottles to make them easier to dispose of. Recommended for restaurants, pubs, bars and special recyclers. Hinged door and 35-second pressing time Integrated bale ejection mechan ...

l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

CP30 PRESS FOR CANS AND OIL FILTERS With its compact design and a pressing force of 8 tons, the CP30 efficiently presses metal cans and large oil filters up to a size of 30 liters. Recommended for car repair shops, paint shops and food manufacturers. Pressing force of 8 tons Low voltage control and emergency stop knob for safe working Easy removal of cans after pressing and drip tray for residual liquid SPECIFICATIONS Dimensions with stand: 2540 mm H × 1105 mm W × 680 mm D Dimensions without stand: 1435 mm H × 615 mm W × 680 mm D Dimensions of the pressing chamber: 475 mm H × 350 mm W × 350 mm D Weight: 245 kg Pressing time: 35 seconds Pressing force: up to 8 tons Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Noise: 70 decibels IP54 protection class CE Certification Made in EU OPTIONS Savings model Suitable for use at sea Galvanized or stainl ...

Maximum pressure: 9 tons Pressing force: 1.94 kg/cm² Bale size: 770x600x500 mm Bale weight: - Power supply: 400 V/4 kW Year of construction: 1997 Productivity: - Price: on request

for pressing PET bottles

Hydraulic tire separator press type SEDA T-REC XXL. For quick separation of tire and rim. Also ideal for alloy rims.

Dear customers, currently we offer a polystyrene press incl. shredder for sale. It is a new machine that has 0 operating hours! Here are a few more technical details: Material to be processed: EPS moulded parts and chips Maximum material density that can be processed: 18 kg/m³ Loading opening: 700 x 360 mm Filling height 1,402 mm Achievable compaction: up to 250 Kg/m³ System throughput: up to 15 kg/h Block dimensions: 130 x 130 mm Power supply: 3x400 VAC+N+PE 50 Hz Connected load: 1.5 KW, 400V 50Hz incl. automatic press pressure regulation with pellet holder Finish: RAL 7035 (light grey) combined with RAL 2011 (deep orange) Incl. water dosing system for direct screw cooling up to 10 litres/h with water shut-off valve. Price plus VAT, which will be shown separately on the invoice. Transport possible worldwide for an extra charge! If you have any questions, please d ...

Maximum pressure: 14 tons Pressing force: 2.92 kg/cm² Bale size: 800x600(600-1000) mm Bale weight: approx. 100 - 200 kg Power supply: 380V/7.5kW Year of construction: 1993 Productivity: approx. 3 bales/hour Price: on request Machine is fully functional, after technical inspection. We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...

Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...

Maximum pressure: 54 tons Pressing force: 5.62 kg/cm² Bale size: 1200x800x1200 mm Bale weight: approx. 500 kg Power supply: 400V / 4 kW Year of construction: 1999, 2000 Productivity: approx. 2 bales/hour Price: on request Machine is fully functional, after technical inspection. We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 30 S Year of construction: 2009 Serial No.: 109138 specifications: Pressing force: 30 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Height from the ground: 1,310 mm Bale size: 1,200 x 800 x 800 - 1,100 mm Bale weight: up to 270 - 360 kg Drive power: 7.5 kW Cycle time: approx. 29 sec. Pressing time: approx. 14 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)

Maximum pressure: 16 tons Pressing force: 2.08 kg/cm² Bale size: 1100x700x950 mm Bale weight: approx. 150-250 kg Power supply: 400V / 4kW Year of construction: 1993 Productivity: approx. 3 bales/hour Price: on request We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

Press for paper or plastic Pressing pressure 5 tons 400 V 16 A Length 80 cm Width 80 cm Height 2 m

Baling press cardboard foil MF100 | 6 t pressing force The MF100 balers are ideal for pressing cardboard, paper, film, clothing and other materials. Volume reduction through compaction of up to 90%. The press is user-friendly with a large filling volume. The automatic bale ejector helps to remove the bales from the baler without any problems. Characteristics: Bale weight of up to 100kg Ideal for use with medium material volumes Fully automatic bale ejection Powerful cylinder for uniform material compaction Hold-down device to reduce material springback CE certified Made in Europe Specifications: Pressing force: 6 t Motor: 1.5 kW 13 Amp Power supply: 220-230 V (1 phase) Machine dimensions (H x W x D): 2371 x 1388 x 1046 mm Transport height: 1876 mm Machine weight: 632 kg Cycle time: 28 seconds Noise level: 65 decibels Bale: Ba ...

Revised and repainted. The images are sample photos of similar machines and are intended to show the execution and quality of the revision. All wear parts are replaced. Filter cloths new. 1 year warranty on the filter press, excluding wear parts. Panel size: 630 x 630 mm Dimensions: approx. 2000 x 1100 x 1500 mm Chamber depth: 25 mm Capacity: 210 litres Operating pressure: 12 / 15 bar Turbidity inlet: flange 2", central Number of plates: 25 plates Material sheets: Polypropylene Material cloths: PP 5009 (white) Design: open filtration Closing pressure: max. 385 bar Painting: primed and painted in RAL 5010, filter trough + drip tray in plastic. Engine hydraulics with single-acting cylinder. Optional double-acting cylinder that retracts the heavy pressure plates. With the single-acting cylinder, the operator has to push the pressure plates back by hand. Optional: fill ...

Maximum pressure: 5 tons Pressing force: 2.17 kg/cm² Bale size: 590 x 390 x 485 mm Bale weight: approx. 25 - 35 kg Power supply: 400V / 2.2 kW Year of construction: 2003 Price: on request Machine is fully functional, after technical inspection. We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

Revised and repainted. The images are sample photos of similar machines and are intended to show the execution and quality of the revision. All wear parts are replaced. Filter cloths new. 1 year warranty on the filter press, excluding wear parts. Panel size: 630 x 630 mm Dimensions: approx. 2900 x 1100 x 1500 mm Chamber depth: 25 mm Capacity: 312 litres Operating pressure: 12 / 15 bar Turbidity inlet: flange 2", central Number of plates: 40 plates Material sheets: Polypropylene Material cloths: PP 5009 (white) Design: open filtration Closing pressure: max. 385 bar Painting: primed and painted in RAL 5010, filter trough + drip tray in plastic, Engine hydraulics with single-acting cylinder. Optional double-acting cylinder that retracts the heavy pressure plates. With the single-acting cylinder, the operator has to push the pressure plates back by hand. Optional: fill ...

used baler Manufacturer: STRAUTMANN Type: BaleTainer Year of construction: 2013 for ramp loading specifications: Pressing force 60 t Main drive power 9.0 kW, Total connected load: 20 kW Bale dimensions 1,100 x 1,100 x 800 mm (W x D x H), 3 discs Bale weight up to 400 kg (3 discs) Binding 4-fold vertical Machine dimensions with task: 6,500 x 1,850 x 2,800 mm (L x W x H) Weight approx. 8,000 kg Control: S7-1200

automatic baler Manufacturer: PRESONA Type: LP 65 VH 2 Year of construction: 2012 specifications: Press force: 65 t Specific pressing force: 7.87 kg/cm² Drive power: 45 kW Throughput: 370 m³/h Filling opening: 1,500 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 425-575 kg Setting: 5-fold vertical Oil tank: approx. 1,000 ltr. capacity Machine weight: approx. 26 t Optionally with chain conveyor belt Manufacturer: BLUETECH Type: Chain Conveyor Belt Year of construction: 2012 Specifications: Conveyor width: approx. 1,500 mm Feed length: approx. 5,000 mm Climbing length: approx. 10,500 mm according to attached pictures

automatic baler Manufacturer: PRESONA Type: LP 65 VH2 Year of construction: 2007 specifications: Press force: 65 t Specific pressing force: 7.27 kg/cm² max. oil pressure: 265 bar Press force pre-press: 25 t Drive power: 45 kW Throughput: approx. 370 m³/h Filling opening: 1,500 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 420-570 kg Setting: 5-fold vertical Oil tank: approx. 1,000 ltr. capacity Machine weight: approx. 21 t Optionally with chain conveyor belt Manufacturer: BLUETECH Type: Chain Conveyor Belt Year of construction: 2007 Specifications: Conveyor width: approx. 1,500 mm Feed length: approx. 6,000 mm Climbing length: approx. 10,500 mm according to attached pictures Subject to errors in the technical data.

Cardboard press, paper press Horizontal version bale size 60x70x70 cm with cutting device Make HSM 14 to Presskraft older model year unknown. Very comfortable due to Insertion shaft and cutting device. The finished bale can be placed directly on a Pallet can be pushed out. Has a large hydraulic agregat runs very fast and quiet. Sale without guarantee/liability or warranty for VB 3.600,--€ plus VAT VAT. Peter Knam Sweden 7 D-88085 Langenargen peterknam.de 07543/4242

used baler Manufacturer: STRAUTMANN Type: BaleTainer Year of construction: 2011 Machine no.: 407.00.360 for ramp loading specifications: Pressing force 60 t Main drive power 9.0 kW, Total connected load: 20 kW Bale dimensions 1,100 x 1,100 x 800 mm (W x D x H), 3 discs Bale weight up to 400 kg (3 discs) Binding 4-fold vertical Machine dimensions with task: 6,500 x 1,850 x 2,800 mm (L x W x H) Weight approx. 8,000 kg Control: S7-1200

It is a special hydraulic chip press designed to achieve the best compaction quality with maximum flexibility in application. It is designed for the recycling and compaction of metal chips (which are shredded if necessary) from machining by converting them into cylindrical briquettes. When it comes to disposing of metal chips, the Styrotec briquetting press saves a lot of money and increases profits by turning waste into a resource. It can be installed both indoors and outdoors. Your benefit: - Volume reduction of up to 90%, which gives you more free space in the warehouse - Higher sales price leads to a quick return on investment - Reduction of handling and transport costs by up to 80% (in-house and during disposal) - Reduction of recycling costs of up to 90% through better recyclability - Reduction of environmental impact Production (general): 20-50 kg/h Briquette diamet ...