ital 고무 기계 사용 판매를 위해

roll diameter: 550 mm roll length: 1500 mm rolls drilled: Kernbohrung Nip adjustment: hydraulisch 0 total power requirement: 90 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 400 mm roll length: 1100 mm rolls drilled: Kernbohrung Nip adjustment: hydraulisch total power requirement: 2x 30 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Refer to code 1032 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

roll diameter: 400 mm roll length: 1000 mm rolls drilled: peripher Nip adjustment: hydraulisch total power requirement: 2x 30 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: 60 mm screw length:: 15D screw speedl:: -- U/min Condition: used Specification: rubber extruder – used - Screw diameter: 60 mm - Screw length approx.: 15D - Sold as seen. The buyer is responsible for safety regulations. No CE marking. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

roll diameter: 400 mm roll length: 1000 mm rolls drilled: Kernbohrung Nip adjustment: hydraulisch 0 total power requirement: 45 kW Condition: used, overhauled Specification: Rolling mill 400 x 1000 mm - second-hand monobloc model, motor under the rolls - roll diameter: 400 mm - roll length: 1000 mm - rolls: with core bore, with central chamber for water cooling - Rollers mounted on bronze bushes with oil circulation lubrication via pump, - equipped with new slewing rings for connection to the water circuit - Gap adjustment: hydraulic, NEW - Hydraulic unit NEW - Tiltable guide plates - stainless steel roller container to hold the mixture - bi-directional rods - safety brake for NOT stop - AC motor: 45 kW - 400 Volt - 50 Hz - Painting: in RAL colours according to customer requirements - new control panel with touch pan ...

Clamping force 500 kN. Extruder 90/24D. Battery head 8 ltr. Strike plates 700 x 800 mm. Opening min/max 650/ 1200 mm. 380V 50Hz

Refer to code 1025 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Clamping force 600 kN. Extruder 120/24D. Battery head 8 ltr. Strike plates 960 x 800 mm, opening path min/max 600/1300 mm. Mould thickness 620 mm. 380V 50 Hz

ZIG ZAG AIR SEPARATING SYSTEM, This innovative system can separate :, metals, stones,paper from plastics or, even heavier plastic flakes from lighter, No need for an air treatment system, since it works in an air closed-loop, can efficiently replace gravimetrical separation tanks or ECS systems when weight of materials is consistently different., very efficient and smart construction:, - fast and precise separation of different types of material, eliminating other more complicated and costly processing;, - constant and precise production thanks to numerous adjustments that can be made to the system;, - possibility of working on all types of material;, - robust construction and reliability;, - simple and minimal maintenance required thanks to the solutions used and the quality components installed., Capacity up to 8 m3/h, Processed material weight from dust to metals, constructed in a stu ...

Refer to code 1049 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Meccanica model Italian 92-liter Banbury and Meccanica model Italian 80-liter Banbury.

Key data: 11000 , 13254 , 150

Presse a injecter ITALTECH BS 1100 T Type : BS-1100/13250 Année : 1999 Diamètre vis : 150 mm Volume injectable : 13254 cm3 Pression d’injection : 1520 bars Epaisseur moule : 450 - 1350 mm

Refer to code 1155 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

STRAND PELLETIZER 250 mm., Fixed pitch, 4 kW motor, 4 poles, IE3 motor drive, Transmission belts, Speed variation via inverter, Electrical panel compliant with CE standards - 400 V, 50 Hz with, 2 x 16 Amp sockets, width 250 mm, Rotor with 12 micrometrically adjustable rotating blades, Counter-blade made in widia, Hardened pressure roller, diameter 60 mm, straignt knurling, Hardened drive roller, diameter 40 mm, straight knurling, Pneumatic piston for presser roller adjustment, Chrome plated parts in contact with the material, Stainless steel discharge, Limit switch with safety lock, Mounted on anti-vibration support with sound proof panels, installed power - used power in work: about 60-65% : 4,0 kw, availability: 70 working days ca, working width: 250 mm, conditions: new machine, type: strand pelletizer for extruders

TWIN SCREW EXTRUSION LINE, Top Italian Constructor, for PVC both soft and rigid, max infeed 10-12 mm size, forced feeding hopper, dosing unit, 2 parallel, counter-rotating screws 118 mm diam. 25 L/D, pressure control;, nitrided steel barrel with degassing vent 2,2 kW, Barrel heating bands kW 76,00, Extruder cooling barrel motors power 4x 0,37 kw, n.7 Heating zones, Extruder a.c. motor 120 KW, Extruder tot power 205 kw, Extruder average absorbed power 105,00 kW, Extruder rpm 8-45, Lubrication pump 1,50 kW, Electric cabinet with inverter and modem for remote diagnosis, semi automatic screenchanger for PVC, granulating head, die face dry pelletizer, cooling unit, Installation and start up included (boarding and travel costs on Buyers charge), Total installed power: 205 kw - 105 kw average in use

CENTRIFUGAL DRYER for pellets (to go with an existing pelletizer), for a 350/400 kg/h capacity of PE PP ABS PS PC flakes, made of sturdy AISI304 stainless steel with vertical axis, driven by a 2.2 kW 3 Ph.asynchronous motor,, complete with soundproofed discharge cyclone, stainless steel tank for water recovery and recycling, 1.1 kW water ump,, equipped with drainage for overflowing, HEAT EXCHANGER GROUP, made of painted carbon steel, internal copper tube bundle, with removable head to facilitate cleaning, fixed to the tank using brackets, float with water replenishment valve, Electrical board of machine wiring, Users manual, CE compliance, installed power - used power in work: about 60-65% : 2.2, conditions: new machine, type: for granulate - this machine goes after the pelletizer, capacity: 300-450 kg/h

WATER RING HORIZONTAL PELLETIZER, Constructed in a stainless steel sturdy structure, 16.25 kw installed power, for PE PP production average 300-400 kg., steam extraction vent, water-water heat exchanging unit (to be connected to a chiller), N.1 die (customized to project), N.4 rotating knives, N.1 blade-holder, N.1 blade adjusting template, N.1 thermoregulated area, Heating power 6 kW, Cutting drive power 3 kW, No. 1 water pump for water re-circulation, ELECTRIC CABINET (OPTIONAL - can be connected to extruders cabinet), This machine is available in other sizes and in dry version., When submitting your enquiry, please give details of :, - MATERIAL type and size, - CAPACITY required, - if CABINET is needed or possible connection with existing extruder cabinet, installed power - used power in work: about 60-65% : 16.25, capacity: 300-400 kg/h

USED VERTICAL MIXER, constructed in sturdy carbon steel, Total height 3.400 mm., Diameter 1.300 mm., Legs 2.150 mm., Barrel height 1.250 mm., Cone height 750 mm., inner screw 180 mm. diam., Nominal capacity 1.800 lt.ca, side discharging pipe, Discharging point 860 mm. from floor., hatch on barrel mm. 500 x 700, 1,5 kw drive, installed power - used power in work: about 60-65% : 1.5, capacity: 1800 lt.

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

USED VERTICAL MIXER, 24 m3 capacity, total height approx 5.400 mm including transmission group + cyclon, max Ø 2.800 mm., constructed in painted electro-welded carbon steel., inner auger diam.350 mm., lower loading hopper with safety grid and sampling shutter,, complete with anti-dust cover, mm.600x500, pulley and belt transmission, protected by carters, electric voltage: 400 V, 50 Hz,, conditions: good working conditions, availability: immediate, width: 2800 mm. special transport

WASHING LINE for PLASTIC SCRAPS, for 350-550 kg/h average capacity depending on contamination and material, material loading screw conveyor with hopper, equipped with vibrating motor, made of stainless steel, stainless steel tank size 5,0 x 1,5 x 2,0 mt. complete with 2 horizontal skimming screw conveyors for material handling. 8.2 kW, 50 Hz., horizontal screw conveyor at the bottom + diagonal screw conveyor for extracting sunk material, stainless steel safeti grate on the upper part, diagonal material collection drainage screw conveyor, drying centrifuge, material extraction fan, electrical panel, the line was built in 2008 and is offered completely reconditioned

UNDERWATER PELLETIZER, up to 1.400 kg/h with soft and rigid PP max 30 MFI, Total installed power 67,14 kW, The supply includes:, Connection from your screen changer to the diverter valve, made of C45 steel heated by mica electric haters., Diverter valve heated with electric heaters This allows the flow of product to be diverted to the drain to bring the extruder up to speed, it consists of a C45 steel body with a specially perforated plate that diverts the flow to the outlet or die. This plate slides via a position-controlled hydraulic cylinder, operated by a hydraulic power unit complete with high-pressure hoses. Pressure and product temperature control probes are also included., Cutting unit consisting of: electrically heated die adapter/diverter valve; AISI304 granulation chamber; die with hard metal inserts, heated by electrical heaters; auger holder unit with blade pressure adjustme ...

UNDERWATER PELLETIZER, for rigid and soft PP max MFI : 30 (and more), electrical heater max 14,6 kW, n.2 thermo regulating zones, A pressure transducer and a melt temperature transducer are mounted on the purge valve. The purge valve is controlled by a hydraulic cylinder connected to a hydraulic power unit with a 2.2 kW motor., Steel die with brazed tungsten carbide plates. A conveyor cone for the molten polymer is installed inside., stainless steel granulation chamber, Impeller shaft with 11 kW 2-pole drive motor (3000 rpm nominal, 4000 rpm max) controlled by an inverter with rpm variation and speed readout on the panel. The shaft output side has special seals and a labyrinth and safety water drainage to protect the motor bearings. The impeller motor is integral with a slide sliding on rolling guides, operated, via a recirculating ball screw, by a manual handwheel equipped with a positi ...

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, conditions: used

HOT MICROPERFORATOR, Maximum working width 1.200 mm, Total roll width 1.300 mm., Maximum working speed 80 mt./min, Inner Ø 118 mm., Fitted with n.12 x 100 mm.bronze needle holding pieces, Nr.9 needles/sqcm, needle Ø 1,42 mm. (or bespoke to project),, 380 V 3Ph+N+E 50 Hz., Electric panel with digital thermometer to pre-set the working temperature, You can select the temperature on the different heaters (central and side), Pneumatic system to open/close the perforating roll., Roll rotation when in stand-by posittion, to avoid material overheating, Easy replacimg counter-roll in organic bristle., Micro-metric adjustment of needles pressure in work, The needle-holding roll can be very easily replaced to a different needle pattern., conditions: new machine, type: Hot microperforator for plastic films

STRAND PELLETIZER 250 mm., Variable pitch, with synchronized pull off unit, 4 kW motor, 4 poles, IE3 motor drive, 1.1 kW motor on pull off unit, Transmission belts, Speed variation via inverter, Electrical panel compliant with CE standards - 400 V, 50 Hz with, 2 x 16 Amp sockets, width 250 mm, Rotor with 12 micrometrically adjustable rotating blades, Counter-blade made in widia, Hardened pressure roller, diameter 60 mm, straignt knurling, Hardened drive roller, diameter 40 mm, straight knurling, Pneumatic piston for presser roller adjustment, Chrome plated parts in contact with the material, Stainless steel discharge, Limit switch with safety lock, Mounted on anti-vibration support with sound proof panels, installed power - used power in work: about 60-65% : 5,1 kw, availability: 70 working days ca, working width: 250mm, conditions: new machine, type: strand pelletizer for extruders

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 14.000 lt.ca, inspection hatch on barrel, loading hopper, control panel, conditions: used

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, conditions: used

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

USED VERTICAL MIXER, constructed in sturdy carbon steel, Nominal capacity 8.500 lt.ca, inspection hatch on barrel, loading hopper, control panel, capacity: 5.000 kg ca, conditions: used

Hydraulic injection moulding machine manufactured in 2011. This ITALTECH KS 1200 8300 ES features a screw diameter of 130 mm and a clamping force of 11,772 kN. It has a shot volume of 8630 cm³ and a maximum injection pressure of 1460 bar. If you are looking to get high-quality injection moulding capabilities, consider the ITALTECH KS 1200 8300 ES machine we have for sale. Contact us for further details.

ROTATING SCREEN, construction in Aisi304 stainless steel, previously working on a 160 mm extrusion line, stainless steel screen with 17 mm holes, 2 exits for lumps and good materials, 0,25 kw motor, Bonfiglioli gearbox, loading hopper 305 x 505 mm., excellent conditions, installed power - used power in work: about 60-65% : 0,25 kw, availability: immediate, conditions: excellent