iddon 고무 기계 사용 판매를 위해

Iddon Cold Feed Extruder. 2.5" screw dia. 10/1 LD Ratio. Motor Size 20.4/5.5 HP

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

Iddon Two Roll Mill 6” diam. x 12” wide Fully guarded and interlocked

Complete Line Consisting of 1.Sheet material unwind station (let off stand) 2. Iddon 1320mm x 450mm dia wide 4 roll inverted L calender manual nip adjustment, even speed gears, auto lubrication system with 45kW AC right angle drive motor and gearbox, Steam heated bowls up to 150c Bowl temperature monitoring system, fabricated bedplate. Overhauled in 2007 (by Iddon) with new side frame and rolls precision ground 3. Edge Trim - make: Mario Cotta 4. Guillotine - Make: Pasquato SNC 5. Wind up

Qty 1 x Iddon 1320mm x 450mm dia wide 4 roll inverted L calender manual nip adjustment, even speed gears (1:1), cored rolls with rotary joints fitted, auto lubrication system with 45kW AC right angle drive variable speed motor and gearbox, fabricated bedplate. Complete with controls. Also available (if required): Sheet material unwind station (let off stand) Simple Cooling unit In-line cutter Accumulator rolls (wind up)

Iddon Extruder Screw diam. 38mm (1.5”) Motor: Reyrolle AC 11/2.2HP 220-250 380-440 volts 1500/300rpm 29/16.5amps Continuous rating

Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel

Three Roll Calender Manufacturer Iddon Bros. ‘I’ shape stack vertical Roll width 54” (1350mm) x 22” (550mm) diam. Even speed Rotary joints for steam heated rolls for water cooling Electrical speed controls with electric autostop Motorised roll stack at the end of the Calender Complete with gearbox, 45kW motor and starter panel The Calendar runs well and goes down to .8mm thick The Calender is mounted on a one-piece fabricated bed plate

Three Roll Calender Manufacturer Iddon Bros. ‘I’ shape stack vertical Roll width 54” (1350mm) x 22” (550mm) diam. Even speed Rotary joints for steam heated rolls for water cooling Electrical speed controls with electric autostop Motorised roll stack at the end of the Calender Complete with gearbox, 45kW motor and starter panel The Calendar runs well and goes down to .8mm thick The Calender is mounted on a one-piece fabricated bed plate

Key data: 300 mm, 600 mm

Iddon 24inch (600mm) x 12inch (300mm) Two Roll Mill Chilled cast iron rolls Rotary joints Right angle drive Radicon Gearbox Fulton Rotary joints AEI electric construction motor Safety bar back and front of mill

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum