4 결과

범주: 307 고무 기계
최신 업데이트: 23.06.2016 감시 목록에 추가
승인
딜러
ankerimg
품목 아니오.: 9267176

사용

check 파는 사람: Euro Rubber Lines
위치: Thornton Land-uk

감시 목록에 추가

Colmec Italy 150mm dia coldfeed extruder, roller feed - 200mm wide, Screw length 2000mm, L/D ratio 13:1, with simple Spaghetti die/cutter assembly, jacketed barrel and cored screw for temperature regulation (no TCU's included). with 100HP, 1750rpm, 575V, 3ph, 60Hz AC motor (ex Canada) and controls. Fabricated bedplate. Screw height: 620mm. In very good condition.

범주: 307 고무 기계 / Rubber extruders
최신 업데이트: 12.03.2026 감시 목록에 추가
승인
딜러
품목 아니오.: 167821862
새로운 기능: 2021

사용

check 파는 사람: Andrew Isaacs Machinery International Ltd
위치: Land-uk
VS

감시 목록에 추가

Colmec 150mm Extruder Model: TGF 150/ 16D LD ratio 16:1 Screw length 2340mm Siemens Motor, 178kW, 1860rpm Hydraulically operated crosshead With Control cabinet With Temperature control unit Spare screw Year 2001

범주: 307 고무 기계 / Rubber extruders
최신 업데이트: 23.05.2026 감시 목록에 추가
승인
딜러
품목 아니오.: 168310834
새로운 기능: 2007

사용

check 파는 사람: MEB Maschinenhandel GmbH
위치: Italien

감시 목록에 추가

screw ø:: 70 mm screw length:: 22D screw speedl:: -- U/min Condition: used Specification: rubber extruder line – used COLMEC Extruder, Hot Air Channel, Cooling Bath Consisting of: Extruder COLMEC 70 x 22D - Screw diameter: 70 mm - Screw length approx.: 22D - Extruder motor power: 37 kW - Cooling unit for extruder Hot air oven: - Hot air oven power: 80 kW - Fan power: 2x 0.36 kW, 2x 1.5 kW - Stainless steel cooling bath The system is in good condition and was still in operation until approx. 6 months ago - Sold as seen. The buyer is responsible for safety regulations. Without CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

범주: 308 기타 플라스틱 기계
최신 업데이트: 08.05.2026 감시 목록에 추가
승인
딜러
품목 아니오.: 107518009
새로운 기능: 2006

사용

check 파는 사람: Reitz Technik GmbH
위치: Biebergemünd Land-de

감시 목록에 추가

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

원하는 기계를 찾지 못하셨습니까? 원하는 문의 보내기 모든 딜러에게 (등록 필요 없음)
Banner ad information  
RESALE since 1996