zerbst 车床 二手 出售

faceplate diameter: 1250 mm turning diameter over slide rest: 2040 mm turning length: mm total power requirement: 55 kW weight of the machine ca.: 12 t dimensions of the machine ca.: m Brand Zerbst Machine no D982 Type DP 1 - 2.040 Ø Digital readout Maximum turning diameter 2.040 mm ø Passage 98 mm ø 4-Jaw Chuck 1.250 mm ø Speed 4,5 - 224 RPM Separate chisel support Engine power 55 kW Excluding slot table Quick-change holder Machine weight 12.000 kg Dimensions: Head: 2.500 x 1.800 x 1.700 mm support: 2.200 x 1.800 x 2.000 mm Electrical panel: 2.200 x 600 x 2.200 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1420 mm turning diameter over slide rest: . mm turning length: 3150 mm faceplate: 500 mm turning speeds: 176 U/min steady: 160 mm total power requirement: kW weight of the machine ca.: 15,68 t dimensions of the machine ca.: m Chip conveyor can be purchased as an option for €7,500 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

faceplate diameter: 3500 mm turning diameter: 4000 mm centre distance: 16000 mm turning speeds: 0,71-33,5 U/min Rest: 2 tailstock quill taper MT: max. workpiece weight -without tailstock: 6300 kg max. workpiece weight between centres: 18000 kg Plate area: mm total power requirement: 31 kW weight of the machine ca.: 60 t dimensions of the machine ca.: 22x5x4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1600 mm, 3500 mm, 800 mm

For sale is: 1 Piece Used Face and Lace Lathe Manufacturer: Werkzeugmaschinenfabrik Zerbst GmbH Type: DP1 / S3 x 3500 Year of manufacture: 1994 Technical data: Largest turning diameter over bed: 1,600mm Center width: 3,500mm Spindle bore: 100mm Face plate diameter: 1,250mm Total mass of the machine: approx. 24.8t incl. documentation Further pictures and videos can be sent on request. The following things have been renewed/repaired on the machine in the last four years: At the end of 2022, the tailstock was completely overhauled. New bearing and new tip and lubrication. 2024 Cross Support regenerated. Refurbishment of the wedge strips with new sliding coating, snatchers on the guideways smoothed by scraping, Bearing seats of the spindles made smooth, wedge strips in the contact surface and covering surface scraped. Lubrication pump cle ...

Change gear, change gears, gear -for: heavy-duty lathe Braun Zerbst -Number: 23 pieces change gears -Module: mm -Dimensions: 530/530/H735 mm -Weight: 144 kg

turning diameter: 3.200 mm turning diameter: modified: 2.400 mm turning diameter over slide: 3.000 mm turning length: max. 15.000 mm control: Sinumerik 840 D Siemens workpiece weight: max. 80.000 kg work accuracy: (up to) 0,01 mm Main spindle:: turning speed range - main spindle: max. 50 min/-1 total power requirement: - kW weight of the machine ca.: 154,4 t dimensions of the machine ca.: 20,7 x 6,0 m Documents: Heavy Duty Lathe ZERBST - DXP 5 / W15x15000 - measurement precision: < 0,01 mm Retrofit 2009 / 2012: - 2009: Control system upgrade to Sinumerik 840D - 2012: - New main gearbox, incl. main spindle drive - Installation of holding brake, incl. electrical integration - Modification and optimization of cylindrical roller bearings/bearings - Modernization: Control and safety technology The data for this ad was created with ModulMWS - the software solution of LogoTech o ...

- 4 chuck 1600 mm - Heidenhain digital read out - Steady rest 710 mm - Powered tailstock - Threath cutting  - Triple guide ways cast irion bed design - For turbine rotors, electrical motor anchors , reactor vessels, cylinders, rope pullys, marine propulsion shaft, castings, shafts and cement industry

Plan - Spiral - Lathe Chuck Diameter 190 mm Centrally adjustable base jaws Individually adjustable top jaws Through-hole 50 mm Bolt circle 176 mm Height 145 mm Weight 14.5 kg

Steady Ø 310 mm

Steady Ø 145 mm

Steady Ø 195 mm

Elma Troyan motor Type: T 100LA 8/4 CB B14F 130-481 380 volt 0,7/1,1 kW 700/1415 rpm

Leroy Somer motor Type: LS80 230/380 volt 1,5 kW 2840 rpm

220/380 volt 2865 rpm 2,2 kW

Freetech motor 0,8/1,1 kW 400 volt 1400/2800 rpm

Steady Ø 65 mm

Steady Ø 60 mm

Type: MI 70 FP F3 30/1 ratio

Carpanelli motor 230/400 volt - 0,25 kW - 1340 rpm 266/460 volt - 0,3 kW - 1600 rpm

AEG motor Type: AM100LS8/4 400V 0,7/1,3 kW 700/1380 rpm

Elprom motor Type: 112M4 B14F165 4 kW 230/400 volt 1420 rpm 30 kg

TOS chuck 200 mm

Efacec universal motors Type: BF5 132M 848 200/230/220/240 volt 2,2/3,3 kW

Type: SW/075T

Aja motor Type: 80/80/4 230 volt 0,8/1,2 kW 1400/2800 rpm

Aja motor Type: 80/80/4 230 volt 0,75/1,17 kW 1400/2800 rpm

Eldrive motor Type: EF 63B 4 1360 rpm

Jinshin motor Type: AEVF - frame: 112M 415 volt 3,7 kW 1430 rpm 40 kg

AEG motor Type: AM80ZCA4/2 230V 0,8/1,2 kW 1425/2800 rpm

Jinshin motor Type: 112M 3,7 kW 220/380V 1430/1720 rpm 45 kg

Leroy Somer Type: LS9013 2,2 kW 220/380V motor 1390/1740 rpm

Elco Cozzi motor Type: CN400 2,2 kW 220/380 volt 1400 rpm

Type: T 132H 4B 220/380V 7,5 kW 1445 rpm

Ansaldo motor Type: A1C 131 1A A000 7,5 kW 2900 rpm 220/380V

Type: C132MB 7,5 kW 380V - 16 amp

Type: T 132 M4 7,5 kW 1460 rpm For Labor 255 lathe

Type: DH 132S 8/4 2,2/3,3 kW 720/1440 rpm For Pinacho lathe SP 90 / 165

Type: AEEEF-PP008 5,5 kW 50 hz - 380V - 12,3 amp 1450 rpm 59 kg

Specification: Automatic plate

different sets for an F 200 3 jaw chuck (base jaws on top jaws)

gebr. Chuck 4 jaws chuck, Fabr. Röhm, 315 mm

Röhm 20641, KFM 130/2, Power Chuck 130 MO KFM 2-Jaws, ZA110 Overall diameter: 130 mm PF003850 Number of Jaws: 2 Jaw Stroke: 5.5 Inner diameter: 46 mm Width: 63 mm Manufacturer's specifications for technical data: Max. actuation force: 5 kN Max. total clamping force: 11 kN max. speed: 3950 rpm rpm min^-1 at that time new price approx. 4500€ You can find more power chucks - new and used - in our shop! International shipping costs on request!

gebr. 3 & 4 jaw chuck from Röhm with 125 mm diameter.

Chucks 4 claw dia:1000 mm

Lathes accessories, measuring equipment etc., contents of this cabinet page