schröder 钣金加工设备 二手 出售

Technical data Manufacturer: Otto Schröder Stroke: 160mm hand adjustable Distance between the stand: 800mm Pass: 250mm Support table: 800mm, with 4 grooves subcircle of 400mm groove dimension 25x75mm Bore: table center of 70mm Table height: 835mm Dimensions: LxWxH 110x900x2200mm

sheet width: 3000 mm plate thickness: 3 mm weight of the machine ca.: t 3 support arms 1 angle stop pneumatic hold-down device Backgauge to be operated by hand The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 3000 mm, 3 mm

with automatic hold-down device POS 100 E Control for Motorized Backgauge Single-angle stop 2 front support arms adjustable on linear rail Manual cutting gap adjustment 0.5 - 3 mm a sheet metal transport and stacking device is attached under the fence for transporting and depositing the cuttings Compressed air connection required Security fencing and light barrier available Adjustable back gauge 8 - 1000 mm Colour: grey/blue Total power requirement: 32 A with cutting gap adjustment without cutting angle adjustment Power: 3000x3.0 mm, 4.0 mm aluminum, 1.5 mm stainless steel Dimensions: 4000 x 1600 mm Weight: 4000 kg Machine number: 200034 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.

Specifications: - Max. working width 3040 mm - max. material thickness 4 mm - Manual cutting angle adjustment - Stroke rate up to 34 1/min - Backgauge with positioning control Pos100 - Table height approx. 850 mm - Front angle stop - 2 front support arms - Rear space protection with light barrier - E-foot switch - Pneumatic connection 6 bar - Drive 400 V - Space requirement without support arms approx. W 4000 x H 1400 x D 2100 mm - Weight approx. 4700 kg

Offer 24483 Specifications: - Max. working width 1020 mm - max. material thickness at 40 kg / mm² strength 4 mm - Bending angle adjustment selectable 6 - 135 ° - 6-fold bending angle preselection - Largest opening width / stroke of the upper beam 250 mm - Height adjustability - bending beam 50 mm - the lower beam 50 mm - E. footswitch - Upper bolster drive 400 V / 2.2 kW - Bending beam drive 400 V / 2.2 kW - Space requirement approx. W 2100 x H 1400 x D 1100 mm - Weight approx. 2000 kg

Offer 24482 Specifications: - Max. working width 1020 mm - Max. material thickness 4.0 mm - Cutting angle 2.4 ° - Single stroke – continuous stroke can be preselected -one. Back gauge up to 700 mm - Front angle stop - Front pull-out sheet metal support - Drive 400 V / 3.4 kW - Space requirement approx. W 1450 x H 1180 x D 1400 mm - Weight approx. 900 kg

Key data: 3020 mm, 3 mm

one. Bending cheek presentation, foot pedal Sheet width: 3020 mm Sheet thickness steel: 3.0 mm Sheet thickness aluminum: 4.0 mm Sheet thickness front: 1.5 mm Back gauge: 1000 mm Colour: white/blue Total power requirement: 32 A Upper beam stroke: 200 mm Bending angle: 145 degrees Dimensions: 4300 x 2600 x 1900 mm Machine weight: 3960 kg Machine number: 220478

Specifications: - Max. working width 2020 mm - max. material thickness at 40 kg / mm² strength 2 mm - Bending angle adjustment pre-selectable 0 - 135 ° - Upper bolster clamping via eccentric lever + foot pedal - Largest opening width / stroke of the upper beam 100 mm - Height adjustability of the lower beam 25 mm - Space requirement approx. W 2950 x H 1200 x D 800 mm - Weight approx. 1450 kg

Key data: 3020 mm, 2 mm

with motor backgauge, numerical NC control, manual bending beam lowering, foot switch Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 3020 mm Sheet thickness steel: 2.0 mm Sheet thickness aluminium: 3.0 mm Sheet thickness front: 1.5 mm Back gauge: 1000 mm Colour: green Total power requirement: 400 V Dimensions: 3800 x 1000 mm Machine weight: 4500 kg Upper beam stroke: 200 mm without roller scissors/ Opening width: 200 mm

Offer 25290 Specifications: - Max. working width 3040 mm - max. material thickness at 40 kg / mm² strength 2 mm - Bending angle adjustment selectable 6 - 135 ° - Largest opening width / stroke of the upper beam 250 mm - Height adjustability - bending beam 50 mm - the lower beam 50 mm - Upper bolster drive 400 V / 0.37 kW - Bending beam drive 400 V / 0.75 kW - Manual backgauge - Split goat's foot bending splint - Space requirement approx. W 4000 x H 1400 x D 1200 mm - Weight approx. 3500 kg

Little-used guillotine shears, only occasionally 1.5 mm sheet thickness Stroke rate 56/ min. Power (Rm 400/mm) 3.5mm Rated power 4.0 kVA Weight 860 kg

An old folding machine Schröder is available. Working width: 2500mm, max. material thickness: 2.5mm, upper beam stroke: 80mm, adjustment: 160mm, speed: 120°/s, working height: 850mm, weight: approx. 3500kg. A visit on site is possible.

Hand-operated 3-roll sheet metal round bending machine with asymmetrical roller order Specifications: - Working width max. 1020 mm - Material thickness max. 1.5 mm - Roller diameter 64 mm - Upper roller turned into a crown, can be swung forward - Rear shaft with handwheel diagonally adjustable for conical rounding - Lower roller adjustment with control lever and eccentric - Front shaft parallel - Space requirement approx. W 1250 x H 950 x D 750 mm - Weight approx. 200 kg

A high-performance crank plate shear with a low operating hours count is offered. Design: all-steel welded construction, stroke rate: 50 strokes/min, control FM 1S, backgauge manual or motorized (MAH 51/52), pneumatic hold-down device, rear safety light barrier. Inspection possible by arrangement.

Offer 25507 Technical data: - Max. working width 2520 mm - Max. material thickness 2.0 mm - Cutting angle 2.2 ° - Stroke rate up to 25 1/min - Back gauge with ELGO positioning control up to 750 mm - Table height 850 mm - Front angle stop 2000 mm - 2 front support arms 1000 mm - pneum. Supported sheet metal hold-up - E-footswitch - Typing - Single stroke pre-selectable - Rear protection grille - Drive 400 V / 3 kW - Space requirement approx. W 3450 x H 1150 x D 2200 mm - Weight approx. 1600 kg

Key data: 3020 mm, 1 mm

in good condition, POS 400 control with digital display, without stop system, with standard rail Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 3020 mm Sheet thickness steel: 1.5 mm Sheet thickness aluminum: 2.0 mm Blechdicke VA/sheet thickness Stainless 1.0 mm Colour: white/blue Dimensions: 3930 x 700 x 1175 mm Machine weight: 2120 kg Motor power: 0.55 kW Upper bolster stroke: 120 mm without cutting device for cutting to length Bending angle (max.: 145 degrees Machine number: 180928

Gr. working width: 4040 mm for sheet metal with a strength of 40 kg up to: 3 mm Upper bolster adjustment: 400 mm Underbeam adjustment approx.: 80 mm Max. bending angle adjustment electrically up to approx.: 180° Upper bolster variable speed drive: 4 kW Bending beam drive: 2 x 3 kW Back gauge, working range: 10 - 750 mm electr. Connection: 400 V Weight: 9 t Space requirement: 5570 x 2250 x 2000 mm high

material width: 300 mm material thickness: 2,0 mm : max. 90° Grad weight: 12 Kg dimensions: 400 x 250 x 100 m Combined sheet metal working machine with: - Bending, tool widths 25 - 50 - 75 - 75 - 105 mm. - Rolls, roll diameter 38 mm - scissors, max. 1015 x 1mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.