lotze 钣金加工设备 二手 出售

Working width: 2500 mm sheet thickness: 4 mm throat depth: 70 mm rear gauge: 520 mm power: 380 V, 6.3 kW space: 3200 x 2300 x 1270 mm weight: 4600 kg

Working width: 5050 mm thickness: 10 mm power: 30 kW space: 2450 x 5600 x 2500 mm weight: 28000 kg

Bending tool, die, lower knife, lower tool, lower beam, -Tool: for folding machine -Widening: for lower cheek -Dimensions: 33/76/3040 mm -Bore distance: 280 mm -Hole diameter: 18 mm -Length: 3040 mm -Weight: 33 kg

Bending tool, die, lower knife, lower tool, lower jaw -Bending tool: from Lotze HDZK swivel bending machine -Widthen: for lower cheek -Dimensions: 2487 x 100 x 15 mm / 190 x 100 x 15 mm -Hole spacing: 100 x 18 mm -Transport dimensions: 2487/100/H30 mm -Total weight: 29.4 kg

Bending tool, die, upper blade, upper tool, upper jaw -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100 mm / M10 -Dimensions: see drawing in the photos -Dimensions: 2678/15/H57 mm -Total weight: 15.7 kg

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/6/H45 mm -Total weight: 5,6 kg

pressure: 300 t chamfer lenght: 3050 mm distance between columns: . mm Control: Cybeleg type: DNC880S total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 3000 mm, 8 mm

Max. cutting length: 3,000 mm Max. sheet thickness: 8 mm steel Motorized backgauge with fine adjustment via handwheel up to 1000 mm Cutting length limitation Knife sharpened Weight: 6,800 kg

sheet width: 6040 mm plate thickness: 4 mm total power requirement: 12 kW weight of the machine ca.: 22 t dimensions of the machine ca.: m - Specification - backstop - Roller tray The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

gebr. Guillotine shears, Helmut Lotze, type 205.3000x16, built 1992 Working width: 3040mm Max. sheet thickness: 16mm Stand width: 3040mm Throat: 200mm Stroke width: 1000mm Motor power: 45kW Stroke rate: 22/min.

Working width: 4040mm, max. sheet thickness steel/stainless steel: 5mm/3mm, back gauge: 1000mm, weight: approx. 7000kg, control system: Elgo, working hours: approx. 22051h. An on-site inspection is possible.

sheet width: 2540 mm plate thickness: 6 mm rear stop: 900 mm down holder: 14 Stk no. of strokes: 20 Hub/min total power requirement: 10 kW dimensions of the machine ca.: 3100 x 2200 x 2600 mm weight: 5000 kg Features: - Central lubrication - Electric rear stop - 1x side stop 2350 mm - 2x front support arms with stop 1700 mm - Front finger guard - Spare blade (used) - Foot switch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3000 mm plate thickness: 8,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 6,80 t dimensions of the machine ca.: m Motorized backgauge with fine adjustment via handwheel up to 1000 mm Cutting length limiter Sharpened blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press brake, bending machine, swing bending machine, die bending machine -Handover: in its current condition as seen, see photos -Condition: upper bending tool has been welded -Manufacturer: LOTZE Swivel bending machine type HDZKE20 -Drive: mechanical -Max. working width: 2000 mm -Max. sheet thickness: 6 mm -Max. intermediate dimension: 235 mm -Connected load: 5.2 kW -Dimensions: 1340/3460/H1400 mm -Weight: 3700 kg

sheet width: 2000 mm plate thickness: 3,5 mm distance between columns: 2050 mm daylight opening: 355 mm total power requirement: kW weight of the machine ca.: 2,8 t dimensions of the machine ca.: 3,5 x 1,5 x 1,5 m Bending machine - Bending angle preselection via limit switches The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: - working length 3500 mm - Stand passage 3050 mm - max pressing force 2000 kN - Distance table / ram max. 480 mm - Stand projection 260 mm - Ram stroke approx. 300 mm - Lifting speeds - Downspeed idle max. 100 mm/sec - Boost speed 80 mm/sec - Downward pressing speed max. 10 mm/sec - Total drive power 25 kW - Space requirement approx. W 4500 x H 3150 x D 2100 mm - Weight approx. 16000 kg -with: - CNC control CYBELEC renewed in 2008 - controlled crowning device - controlled backgauge with height adjustment 5 - 1000 mm - hydr. Tool clamping - Upper tool + universal die tool - Material requirements - Two-hand control panel

Key data: 3100 mm, 2700 mm, 2300 mm

Hydraulic press brake - conventional including paternoster system for uncomplicated tool change with 25 hangers. for export NC Press Brake Heut Lotze Type: PZ 100 - 25 Built in 1973 Pressure 100 t Bending length 2500 mm Stand width 2100 mm Weight approx.: 11.000 kg, Dimensions (LxWxH) approx.: 3,100 x 2,300 x 2,700 mm -------------------------- Paternostar system Schwab Maschinenbau Type: SIB 430/340 Built in 1982 Number of compartments 25 max. shelf load 150 Dpa max. device payload 3750 Press brake and paternoster can be purchased separately Maschinenhandel Nord new & used machines for industry, trade and commerce Import/Export Service & Advice Also take a look at our Other Ads. Many more drills available Or visit our more than 1000m² exhibition hall with new and used industrial and manufacturing machines, not far from the A20 motorway!

material width: 300 mm material thickness: 2,0 mm : max. 90° Grad weight: 12 Kg dimensions: 400 x 250 x 100 m Combined sheet metal working machine with: - Bending, tool widths 25 - 50 - 75 - 75 - 105 mm. - Rolls, roll diameter 38 mm - scissors, max. 1015 x 1mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.