paal プレス 中古 販売のため

Manufacturer: Paal Model : Konti 275 G Year of Manufacture : 2010 Find more here - / Contact us at -

automatic baler Manufacturer: PAAL Type: PACOMAT IS Year of construction: 1988 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Channel size: 700 x 700 mm Opening: 800 x 650 mm Drive power: 22 kW Throughput: 100 m³/h with additional manual hopper Wire flow in the pressing direction seen on the left side

New hydraulic pump QX61-250/63-100R88 for PAAL channel baler. Can be used in systems with a 75kW motor.

automatic baler Manufacturer: PAAL Type: KONTI 275 C Year of construction 1996 specifications: Press force: 65 t Specific pressing force: 7.88 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 450 - 600 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 45 + 30 kW Throughput: 380 m³/h Pressing capacity: - approx. 13.0 t/h at department store (35 kg/m³ bulk density) - approx. 23.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 35.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 21.0 t Optionally with feeding belt according to photos

used chain conveyor belt Manufacturer: PAAL Type: KEL 1000 Year of construction: 1997 specifications: Conveying width: approx. 1,000 mm Center distance:approx. 7,500 mm Band course: ascending over the entire length, Conveyor belt drive power: 3.0 kW Side bolster height: 500 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE

Brand new gear pump, with internal gearing for PAAL Konti, Pacomat channel baling press. Can be used in systems with a motor of at least 22 kW

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of construction: 2008 specifications: Conveyor width: approx. 1,500 mm Wheelbase:approx. 9,625 mm Strip course: approx. 2,935 mm horizontally underfloor, then rising to a length of approx. 4,500 mm below 28°, sloping below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE as far as possible pre-assembled, consisting of: - Strip scaffolding in solidly welded section steel and sheet steel edge construction, - additional sliding guides underneath the belt support profiles in the horizontal and climbing sections to support heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with 2 ...

automatic baler Manufacturer: PAAL Type PACOMAT II S SO Year of construction: 1994 specifications: Pressing force: 50 t Specific pressing force: 7.14 kg/cm² Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm Drive power: 45 kW Throughput: approx. 170 m³/h automatic 4-fold horizontal binding

Dual hydraulic pump for PAAL, 45kW Used 2-piece hydraulic pump for PAAL channel baling press. Can be used in systems with a 45 kW motor

Baler Paal Pacomat II with hopper, built in 1979 Specifications: Manufacturer: Paal Type: Pacomat II Year of Make: 1979 Drive power: 11 kW Pressing force: 27 t Channel cross-section: 700 x 1000 mm Filling opening: 1000 x 650 mm Flow rate: approx. 60/115 m³/h Bale size: 700 x 1000 mm Bale weight: up to 400 kg Machine dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine weight: approx. 5200 kg Materials: paper, cardboard, foil Remarks: The machine is in working condition. It was inspected and tested by us in 28816 Stuhr. You can find the video on our website or our Youtube channel. Viewings, also under power, are possible at any time by arrangement. On request, we also carry out tests with your material for an expense allowance. We will also be happy to answer any questions you may have about the machine by phone from Monday to Thursday from 08.00 to 14.00 ...

used box press Manufacturer: PAAL Type: HS 34 specifications: Filling box size: 1,000 x 700 x 2,200 mm (W x D x L) Filling opening: - 1st filling: 2,200 x 1,000 mm - 2nd filling: 1,200 x 1,000 mm Press pressure: approx. 18 t Drive power: 4 kW Lifting speed pre-pressing and retraction: 2.5 m/min. Lifting speed repressing: 1.25 m/min. Bale size: approx. 700 x 1,000 x 1,300 mm Bale weight: up to approx. 300 kg Weight of the machine: approx. 2000 kg Machine dimensions: 3,500 x 1950 x 1,450 mm (L x W x H)

automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 Machine was only in operation for 4 years specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 42 t Attached pictures are only sample pictures!

automatic baler Manafacture: PAAL Type: PACOMAT IS Year of construction: 1993 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Duct format: 700 x 700 mm Filling opening: 800 x 650 mm Drive power: 18.5 kW Throughput: 80 m³/h with additional manual feed hopper Wire passage seen in the direction of pressing on the left side

used baler Manufacturer: PAAL Type: LIKON 110/150 Year of construction: May 2004 Specifications: Press weight up to: approx. 36 tons Press force at 275 bar: 150 t Operating pressure max. 320 bar Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 2 x 75 kW Flow rate: 425 m³/h Binding: 5-fold horizontal Total connected load: 176 kW Rated current: 340 A Pre-fuse (min.) 400 A Operating voltage: 3 x 400 VAC/50 Hz/N/PE Control voltage: 230 VAC / 24 VDC including: - Oil cooling - Low-pressure circuit - Free kicks - Key locking system Transport dimensions: Length: 13,803 mm Width: 2,500 mm Height: 3,164 mm without wire unwinding devices, without binding wire, without feed belt, without a personal protection system, without conveyor belt hopper and withou ...

automatic baling press Manufacturer: PAAL Type: KONTI 275 F Built: 2007 Main parts of the press: 1 automatic duct press (without wire winding devices) 1 automatic lacing 1 Hydraulic system 1 Electric control technical data: Pressing force: 800 kN / 80 t at 300 bar Specific pressing force: 9.70 kg/cm2 Channel cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,600mm Number of connecting wires: 4 pieces vertically Drive power: Main pump: 1 x 45 kW Pump delivery capacity: 1 x 380 l/min Throughput: up to approx. 280 m3/h under operating conditions Performance at: - 35 kg/m3 bulk weight: approx. 9.5 t/h - 60 kg/m3 bulk weight: approx. 16.5 t/h - 100 kg/m3 bulk weight: approx. 26.0 t/h Hydraulic oil tank volume: 2,100 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Other equipment: Operator Panel MP 270 auto ...

automatic baler Manufacturer: PAAL Type: KONTI 275 D/k Year of construction 1999 specifications: Pressing force: 75 t Specific pressing force: 9.09 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 500 - 750 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 75 kW Throughput: 350 m³/h Pressing capacity: - approx. 12.0 t/h at department store (35 kg/m³ bulk density) - approx. 21.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 33.0 t/h for collected goods (100 kg/m³ bulk density) Binding: 4-fold vertical + 3-fold horizontal Machine weight: approx. 25.0 t

automatic baler Manufacturer: PAAL Type: KONTI 700 G/S Year of construction 2010 specifications: Press force: 1940 kN/ 198 t at 300 bar Specific pressing force: 160 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 75 kW Throughput capacity (according to manufacturer's specifications): approx. 650 m³/h Capacity at 35 kg/m³: 22.5 t/h Capacity at 60 kg/m³: 36.5 t/h Capacity at 100 kg/m³: 55.5 t/h Binding: 5-fold vertical Bale weight: approx. 800 - 1,450 kg depending on baled material and bale length Machine weight: up to approx. 47 t

Used Triple Hydraulic Pump QX51-125/53-063/52-063R91 for PAAL channel baler. Can be used in systems with a 45 kW or 55 kW motor. Manufacturer partnumber: QX51-125/53-063/52-063R91

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 1990 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 78 kW Rated current: 150 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press.  ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 1996 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 82 kW Rated current: 162 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press. T ...

Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic

Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance

automatic baler Manufacturer: PAAL Type: KONTI 600 G/S/K with cross-binding Year of construction 2012 Operating hours: approx. 44,700 hours specifications: Press force: 1,546 kN System pressure: 315 bar Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 55 kW Pump capacity: 3 x 420 Ltr. Oil tank volume: 3,100 ltr. Throughput:approx. 780 m³/h Capacity at idle: approx. 1,220 m³/h Capacity at 35 kg/m³: approx. 26.5 t/h Output at 60 kg/m³: approx. 44.0 t/h Output at 100 kg/m³: approx. 69.0 t/h Control: Siemens S7 Setting: 5-fold vertical Additional 4-fold automatic horizontal tying Bale weight: approx. 800 - 1,250 kg depending on the material to be pressed and bale length Machine weight: up to approx. 42 t Includes a top pressure plate slot cover Printing plate was renewe ...

automatic baler Manufacturer: PAAL Type: KONTI 200 C Year of construction: 1993 specifications: Press force: 50 t Channel format: 750 x 1,100 mm Specific pressing force: 6.06 kg/cm² Bale weight: 425 - 550 kg, depending on material and bale length Infill opening: 1,400 x 1,020 mm Drive power: 45 kW Throughput: 200 m³/h Pressing capacity: - approx. 7.35 t/h layered at department store (35 kg/m³ bulk density) - approx. 12.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 20.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 17 t

automatic baler Manufacturer: PAAL Type: KONTI 125 Year of Make: 1988 Operating hours: approx. 23660 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Binding: 3-fold vertical Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: approx. 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)

used baler Manufacturer: PAAL Type: PACOMAT I-35 Year of Make: 2008 specifications: Press force: 35 t Specific pressing force: 7.14 kg/cm² Drive power: 22 kW Throughput: up to approx. 85 m³/h under operating conditions Channel format: 700 x 700 mm Filling opening: 800 x 620 mm Machine weight: up to approx. 6.5 t (depending on equipment)

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers,  ...

Specifications Maximum pressure: 85 tons Year of Make: 1994 Pressing force: 103 tons/m² Number of ties: 4 - vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1750 mm Bale weight: 500-650 kg Weight: 26 tons Power connection: 400 V/ 55 kW Bale tying: automatic

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...

Baler Paal Konti 200 D, built in 2000, optionally with matching conveyor belt Paal KEM-1400 Technical data: Manufacturer: Paal Type Paal Konti 200 D Year of construction 2000 Hours: 28155 Pressing force 60 t Drive power 45 kW Total connection 60 kW Filling opening 1020 x 1400 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying throughput at 35 kg/m³ approx. 9.5 t/h 60 kg/m³ approx. 16.5 t/h 100 kg/m³ approx. 26 t/h Bale weight 450 to 650 kg Transport dimensions approx. 10123 x 2152 x 2720 mm (LxWxH) Machine weight approx. 15,000 kg Materials: paper, cardboard, foil The press is in good condition and has been inspected and tested. You can find a video on our website or YouTube channel. The complete documentation is available. Please note: All technical data refer to the manufacturer's specifications. We a ...

Fully automatic baler Manufacturer: PAAL Type KONTI 275 D Year of Make: 2000 specifications: Press force: 75 t Drive power: 1 x 45 kW Total connected load: kW __ / 170 A Throughput under operating conditions: 280 m³/h Filling opening: 1,020 x 1,550 mm Bale size:750 x 1,100 mm Binding: 4-fold vertical incl. front printing plate slot cover Machine weight: approx. 25 t Bale weights: up to approx. 600 kg Including: - Free kicks - Large digit display

automatic baler Manufacturer: PAAL Type: KONTI 700 G/S Year of construction 2010 Technical data: Press force: 1940 kN/ 198 t at 300 bar Specific pressing force: 160 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 75 kW Throughput capacity (according to manufacturer's specifications): approx. 650 m³/h Capacity at 35 kg/m³: 22.5 t/h Capacity at 60 kg/m³: 36.5 t/h Capacity at 100 kg/m³: 55.5 t/h Binding: 5-fold vertical Bale weight: approx. 800 - 1,450 kg depending on baled material and bale length Machine weight: up to approx. 47 t Optional: with Bollegraaf steel plate strip according to picture

Technical data Maximum pressure: 50 tons Year of Make: 1994 Pressing force: 7.14 kg/cm² Number of bindings: 3 horizontal Channel cross-section: 1000 x 700 mm Dimensions of the tailgate: 145 x 95 cm Bale weight: do 500 kg Weight: approx. 10 tons Power connection: 400 V/ 45 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance

Specifications Maximum pressure: 75 tons Year of Make: 1999 Press force: 90.9 t/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1550 mm Bale weight: 500-750 kg Weight: approx. 25 tons Power connection: 400 V Bale tying: automatic Motor: 75 kW (possibility of switching to 55 or 45 kW) Press capacity at idle: max 750 m³ / hour Press capacity under operating conditions: max 350 m³ / hour Theoretical throughput to density 35 kg/m3: approx. 12 tons/hour Theoretical throughput to density 60 kg/m3: approx. 21 tons/hour Theoretical throughput to density 100 kg/m3: approx. 33 tons/hour Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Cho ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...

LIKON 200C Horizontal Baler Machine Technical specifications: Engine power - 22 kW Year of production - 1994 With oil cooler Horizontal binding x 4 times Press force - 30 t Overall dimensions of the baler: 10000 x 2000 x 2750 mm Press weight: 10 t Loading opening dimensions: 1400 x 700 mm Bundle dimensions - 700 x 1100 x 1000-1200 mm, variable length With hydraulic oil No binding wire It worked in a printing shop without a conveyor belt, only with dry-shredded printing waste! Motorcycle hours - 62639 The baler is in good condition, ready for operation PRICE ON REQUEST! ----- Horizontal Baller Paal LIKON 200C Technische Daten: Motorleistung - 22 kW Produktionsjahr - 1994. Mit Ölkühler Horizontale Bindung x 4 Mal Presskraft - 30 t Gesamtabmessungen der Presse: 10000x2000x2750 mm Eigengewicht der ...

used baler Herateller: PAAL Type: PACOMAT II Year of Make: 1995 Specifications: Pressing force: 27 t Drive power: 18.5 kW Total connected load: 25 kW Throughput: 115 m³/h Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm (H x W)

Technical data: Maximum pressure: 60 tons Year of Make: 1999 Press force: 72.7 t/cm² Number of Bindings: 4 Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1400 mm Bale weight: 450-650 kg Weight: approx. 20 tons Power connection: 400 V/ 45 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance If you have any further questions about this or similar channel balers, please do not hesitate to contact us by email or phone!

automatic baler Manufacturer: PAAL Type: Pacomat IS Year of Make: 1990 specifications: Pressing force: 27 t Specific pressing force: 5.51 kg/cm² Total connected load: 23 kW Rated current: 46 A Main drive power: 18.5 kW Capacity: 80 m³/h Control: Siemens S5 100 U Bale size: 700 x 700 Filling opening: 800 x 600 mm

automatic baler Manufacturer: PAAL Type: KONTI 125 SO Year of Make: 1990 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)

automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 only 4 years in operation specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 39 t

Maximum pressure: 50 tons Year of Make: 2006 Pressing force: 65 tons/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1000 mm Dimensions of the tailgate: 920 x 1400 mm Bale weight: 350-500 kg Weight: approx. 13 tons Power connection: 400 V/ 22 kW Bale tying: automatic

Manufacturer: PAAL Model: KONTI 700 G/S/K Year of Manufacture: 2011 Type of Machine :Baling Press Key Features - Cross-lacing system (optionally switchable) - Oil cooling system - CE marked Find more here - / Contact us at -

Baler Paal Konti 325 D/SO, built in 1999 Technical data: Manufacturer: Paal Type Paal Konti 325 D/SO Built in 1999 Hours: 50702 Press force 94 t Drive power: 2 x 45 kW Total connection 104 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying Throughput at 35 kg/m³ approx. 14 t/h 60 kg/m³ approx. 24 t/h 100 kg/m³ approx. 38 t/h Bale weight 525 to 800 kg Transport dimensions approx. 12352 x 2340 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment is made ex wor ...

Available from 15.05.2026 Baler Paal Konti 325 G, built in 2013 Technical data: Manufacturer: Paal Type Konti 325 G Year of construction 2013 Operating hours 11,723 (as of 10.02.26) Press force 100 t Drive power 2 x 55 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable Setting 5-fold automatic Throughput at 35 kg/m³ approx. 13.5 t/h 60 kg/m³ approx. 21.5 t/h 100 kg/m³ approx. 33 t/h Bale weight up to 800 kg Transport dimensions approx. 12216 x 2530 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sal ...

BALLER PAAL KONTI 425 C Technical specifications: Manufacturer: Paal Type: Konti 425C Year of manufacture: 1995 Klsdm Ajx Dk Ttsty Atel Feed opening: 102 x 175 cm Drive power: 170 kW Caedm Atyexx Su Uo Atsa Compression force: 85 t Settings: Horizontal, fully automatic Roll weight: 500-650 kg Press weight: 25 t PRICE ON REQUEST! ----- BALLER PAAL KONTI 425 C Technische Daten: Hersteller: Paal Typ: Konti 425C Herstellungsjahr: 1995 Bwsbjycfuqsmcbw Nveh Einfüllöffnung: 102 x 175 cm Antriebsleistung: 170 kW Kompressionskraft: 85 t Einstellungen: Horizontal, Vollautomatisch Rollengewicht: 500-650 kg Pressgewicht: 25 t PREIS BEI ANFRAGE!

For sale: Paal Konti 425 D horizontal baler Technical specifications: Manufacturer: Paal Type: Konti 425D Year of manufacture: 2002 Feed opening: 102 x 200 cm Drive power: 2 x 45, 2 x 75 kW Kledex Dlanem Aty Atsl Pressing force: 115 t Settings: Horizontal, fully automatic Roll weight: 550-850 kg Pressing weight: 36 t PRICE ON REQUEST! ----- Verkaufen horizontal Baller Paal Konti 425 D Technische Daten: Hersteller: Paal Typ: Konti 425D Baujahr: 2002 Einfüllöffnung: 102 x 200 cm Antriebsleistung: 2 x 45, 2 x 75 kW Druckkraft: 115 t Einstellungen: Horizontal, Vollautomatisch Rollengewicht: 550-850 kg Pressgewicht: 36 t PREIS BEI ANFRAGE!

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Manufacturer: METSO LINDEMANN Type of Machine : Press Shear Year of Manufacture: 2010 Technical Condition: Good After major renovation in 2023 Meter reading: 18,500 Mt/h Technical Data - Power Supply: Electric 3 x 90KV - Cutting Force: 630 tons - Scrap Compression Force: 630 tons - Number of Pumps: 3 pcs - Capacity: Approx. 8-22 tons/h - Loading Scrap: Left or Right Side - Loading Box: 12m³ - Total Weight (Machine + Container): 75 tons - Control: Remote Control - Hydraulic Oil Capacity: 6,500 liters Find more here - / Contact us at -

CARDBOARD PRESS SPECIFICATIONS Manufacturer: Presona Model: LP50VH2 Year of Manufacture: 2014 Maximum Pressing Force: 500 kN Maximum Oil Pressure: 25 MPa Type: Cardboard Press Condition: Used CONVEYOR BELT SPECIFICATIONS Manufacturer: Topeko Year of Manufacture: 2008 Length: 18 metres Width: 1.25 metres Motor: 40 kW Voltage: 400V / 50Hz Refurbishment: Completely rebuilt September 2024(chains, belts, all components replaced, outer frame only retained) Find more here - / Contact us at -