matec ふるいにく機 中古 販売のため

Drum chipper with 2-blade rotor, 2 counter blades, interchangeable mesh screen Infeed height 400 mm Infeed width 1690 mm 1 large feed roller above 3 smaller feed rollers down Drive electric engine 55 kW (up to 200 kW upgradeable) suitable for round timber, sawmill waste, waste wood, etc. with loading with vibro channel length 6 m, vibro drive MATEC size 3, 4 kW Disposal with vibro sieve tray length 4 m, vibro drive MATEC size 1, 3 kW for oversize feedback with -MATEC Vibrair vibrochannel pneumatical -PVC belt conveyor for returning oversized material to the chipper Machine in almost new condition, only a few hours of operation Electric plant to customer demand and allocation Warranty 24 months on all non - wear parts Contact Peter Ari Schär of MATEC Technical changes, errors and intermediate sale preserved!

MATEC easily from our own development and production running lightly and quietly and transport bulk material and individual loads up to 250 kg with minimal energy over long distances up to 12 m at a time with a hand drill 300 w power consumption. The combined forced - and promotion of resonance stores the kinetic energy in the spring and must compensate for only the frictional resistance of the material. Sawdust, shavings, gravel, Earth, grain, hay and grass, etc. are exactly same speed transported with approximately 17 m / min. by means of Frequenzumforner the speed can be adjusted. The transport and screening in a single operation with a built-in sieve base perforation on request MATEC Vibrorinne standard Trough width inner 500 mm Trough height inner 260 mm current trough length 2500 mm (can front and rear to 1.5 m be extended without additional support) In addition current ...

The MATEC HMS-350 Kleinshredder for professionals, with hammer mill is suitable for crushing of green waste, etc. All types of green waste such as bouquets, garden waste, potted plants, compost in each State, agricultural waste, Earth, cemetery waste, large wood chips and small wood waste, etc. can thus be crushed. The hammer mill is equipped with impact tools made of HARDOX, the appropriate anvil blow bar and the following "data" also made of HARDOX. The content of flower pots, flower boxes, "baked together" grass cutting, etc. can thus be crushed. The combination of anvil blow bar before calibration and subsequent anvil calculation for fine crushing results a high throughput capacity with a small expenditure of energy. Electric motor 7.5 kW, a diesel engine can 3x400V, 50 Hz, power outlet connection euro 32 A request be built up 350 mm diameter insertion slot flight circle diame ...

The ECOSTAR 8 slices hacker with diesel drive 35 HP, 3 cyl., with an increased swivel discharge for horticulture, wine fruit, forestry, agriculture, etc. at a cheap price. With 2 blades, disk diameter 605 mm, disc speed 1200 rpm, JD diesel engine 3100, 3 cyl, 35 HP, water-cooled, feed height 200 mm, max wood diameter 200 mm, Einzugbreit 225 mm, hopper opening 600/600 mm, output per hour 5-8 cubic metres. The machine is ready for use within 1 minute. The chips can easily be abandoned on the bridge of the towing vehicle. The tedious tying of the branches fall away. Take the chips only 1 time in the hands. Watch the video movie in matnews91 on YouTube: ECOSTAR diesel JD3100 8. Price does not include trailer euro 9' 390.00 Expressly subject to technical changes, prior sale and error! Shipping costs CH / DE trucked approximately euro 280.00 MATEC systems + technology GmbH K ...

Wood chopper f. tractor PTO wood chipper ECOSTAR 8 as a kit for the self-Assembly (image mounted with other rotating device) - feeder height width 20/20 cm - upper feed roller with belt drive - disk hacker with 2 knives and 1 counter knife - rated about 5 cubic metres chip length nominal 15 mm - CE compliant - PTO - rotating ejector - delivered in metal crates -Warranty: 2 years on all non - consumable - options for an additional fee: - machine Assembly by supplier - pulverizing integrated to avoid excess - special execution for the manufacture of Pelletschnitzeln with 6 mm length - professional Rotary chute which together does not rust and freezes at Sub-zero temperatures, with lever - built diesel drive 35 HP - electric motor 15 kW model changes built up which are not exactly the figurative representation are reserved! Spare parts/service MATEC CH-4952 Eriswil/DE-79618 Rheinfe ...

Vibrorinne MATEC vibrating mesh drive 4 4 kW, 3 x 400 V 50 Hz Pan nominal width 600 mm Gutter inner width 500 mm Trough depth 260 mm Extra deep OK built channel 480 mm Gutter length approx. 11'000 mm Transport speed nominal approx. 17 m / min Year 2018 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Drum chipper MATEC economy THS 600-2/6 -Catchment level / nominal height 200 mm, hacker feeder height Max 300 -Catchment width 600 mm -Rotor diameter 600 mm -Number of rotor blade 2 -Number counter Blade 2 -Screen of change of perforation 50/50 -Steak size nominal TMP quality 25/25 mm -Feed rollers top 2 -Feed rollers down 2 -Geared motor indent above 2.2 kW -Geared motor indent below 2.2 kW -Weight approx. 2000 kg -Hacker main motor 45 kW/3 x 380 V -Feeding speed nominal approx. 24 m / min. New machine, ready for use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Vibrorinne MATEC drive rear Overtime separation and â repatriation Vibro Drive 1 electric motor 3 kW Linder nominal width inside 500 mm Preparing for 1700 mm Linen nominal length 4000 mm Peasant sheet seal unit perforation 20 mm Weight about 560 kg Built in 2018, new The machine is in very good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

The robust single-shaft shredder is equipped with 7 offset 40/40 mm indexable blades on the rotor The extremely robust design allows the shredding of data carriers such as hard drives, etc., files with metal components, wood-metal mixed material, metal-plastic material, recycling material, textile and carpet, rubber waste, horse manure, etc., sheep's wool, compost, etc. Technical data: 1 rotor with 7 offset indexable blades 40/40 mm 1 profiled counter blade 1 interchangeable screen perforation 20 mm round (can be adapted as required) Feed width 366 mm Rotor diameter 330 mm Motor 7.5 kW, 3x380 V, 50 Hz (can be made stronger) Speed approx. 580 rpm (a gearbox can be set up for low speeds) Machine new Information from Peter Ari Schär from MATEC Changes, errors, prior sale reserved ! Manufacturer: MATEC system+technik GmbH Mechanical engineering Eisenbahnstrasse ...