guilliet 機械の計画 中古 販売のため

Key data: 4 , 220 , 120

Guiliet Profilier and Hobelautmat with Wepla heads Model: 220 KXR 220 Year built:1990 Condition: very good (used) MAX CROSS-SECTION 220 X 120 MM MIN CROSS-SECTION 30 X 6 MM ENTRANCE TABLE 2000 MM long. PLANING SHAFTS 40 MM Dressing shaft 5.5 kW right and left planing shaft combined 5,5kW Thickness planer shaft 5.5 kW WEIGHT APPROX. 1600 KG Cleaned, maintained and functionally tested. If necessary, we can gladly offer planing heads with continuous cutting edges.

Number of boring spindles: 4 St. Working width: 220 mm Working height: 120 mm Length of the planing table: 2.000 mm Feed motor: 1,5 kW Feed speed: 4,5 - 27 m/min. total power requirement: 15,5 kw Dimensions (L/W/H): 3.700 x 1.500 x 1.300 mm weight of the machine ca.: 1.600 kg turning speeds: 6.000 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of boring spindles: 2 St. Working width: 180 mm Working height: 120 mm Length of the planing table: 2100 mm Feed motor: 3,7 kW Feed speed: m/min. total power requirement: kw Dimensions (L/W/H): mm weight of the machine ca.: kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SPECIFICATIONS: Feed length: 1970 mm Machinable width: 230 mm Machinable height: 110 mm Spindles: Ø 40 mm Number of Spindles: 4 Shaft drive Installed power: 16 kW Voltage: 380 V Spindle configuration: I bottom: 3.7 kW II right: 5.5 kW III left: 5.5 kW IV: top: 5.5 kW

Key data: 4 , 180 mm, 120 mm

Used machine Workpiece width 180mm Workpiece height 120mm 4 spindles: 1) Horizontal bottom 180mm 3.7kW 2) Vertical right 120mm 4kW 3) Vertical left 120mm 4kW 4) Horizontal top 180mm 5.5kW Diameter of spindles 30mm

Key data: 4 , 180 mm, 130 mm

Four-way planer Guilliet Type KXY Year of manufacture 1989 Planing width maximum 180 mm Planing height maximum 130 mm 4 planing shafts Knife length 186 mm and 136 mm Minimum planing 30 mm x 6 mm Dressing table length 2000 mm Feed speeds 6 and 12 m/min. Spindle diameter 30 mm Feed motor 0.55 kW Lower dressing shaft approx. 3.7 kW Right wave approx. 3.7 kW Left wave approx. 3.7 kW Above approx. 5.5 kW Height adjustment 0.18 kW Extraction connection diameter 160, 120 and 140 mm Including planer heads Dimensions 3200 mm x 1400 mm x height 1700 mm Weight 1200 kg The first picture shows identical machine in our warehouse

Number of boring spindles: 4 St. Working width: 180 mm Working height: 120 mm Feed speed: ca. 10 m/min m/min. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Type MB6023HK Working width 230 mm Working height 150 mm 6 spindles B, R,L, T, T,B Spindle diameters 40 mm Feeding speed 5-30 m/min Total power. 38.25kW Transport dimensions 3750x1600x1500mm Weight 3400 kg Price 21300 Eur (EXW Jonava, Lithuania

Thicknesser SCM S520 Working width 520mm Working height 250mm Feed speed adjustable: 4 degrees Shaft with traditional knives 4-knife shaft Power 4kw Weight: 670kg

CATALOG NO. 6946 TECHNICAL SPECIFICATIONS - max width of the workpiece 210mm - max thickness of the workpiece 120mm - number of spindles 2 pcs - spindle diameter 50mm in advance: - 3 insertion, pulling, rubber, smooth shafts including 2 double - 2 leading, rubber, pulling shafts including 1 double - heads on supports - head adjustment up / down - electric height adjustment of the upper head - electrical setting of planing thickness - spindles equipped with a brake - main motor 2×5,5kW - smooth regulation of feed speed - feed motor 3kW - feed on cardan shafts - diameter of extraction connection 2x160mm - dimensions length / width / height 2350x1780x1950mm - weight 1882kg – German production – jointers – for sharpening knives on the head – 2 Hydro heads included – unpainted – very good condition, used planer Net price: 33900 PLN Net price: 7533 ...

Heavy two-sided planing machine in special design - used (overhauled in 2015), . The machine is designed for demanding suitable for machining slats and beams. SPECIFICATIONS Work dimensions: Working width: up to 220 mm Working thickness: 20 - 80 mm Working length: min. 1,500 mm Table height: 900 mm Feed speed: 20 – (120) m/min. The machine will run at Tilly max. 60m/minute Drive motors Dressing shaft: 22 kW Thickness shaft: 30 kW Feed: 7.5 kW Lifting gear motor: 1.5 kW Tool: Horizontal shaft speed: 5,000 rpm Diameter of the tools: Horizontal shafts: 200 mm Chip removal: The maximum decrease depends on the feed speed of the workpiece width, wood texture, installed drive power and the depends on the desired surface quality. For specific information, please for your inquiry. Dressing shaft: up to 10 mm with full working width approx. 2.0 mm Thickness shaft: up t ...

Planer Planer COMEVA MB 500 Working width 510mm 4-knife shaft Traditional knives Worktop length 2630mm Sampler tilted at an angle of 45° Engine power 4kw Uttering combs CE Certificate

SCM F5L planer Working width 500mm 4kw main motor 4-knife shaft Traditional knives Main fence adjustable at an angle up to 45 Table top length 2600mm

SPECIFICATIONS Pilot plane on the entrance side: 2000 mm Grooved table Machinable width: max. 180 mm Machinable height: max. 150 mm Spindle diameter: 40 mm Shaft drive Drive shaft power: 4.0 Kw Soundproof booth Spindle Configuration: I Shaft: Bottom 4.0 kW II Shaft: Right 4.0 kW III Shaft: Left 5.5 kW IV Shaft: Right 5.5 kW V Shaft: Top 11.0 kW VI Shaft: Bottom 4.0 kW VII Shaft: Top 11.0 kW VIII Shaft: Universal 4.0 kW

Thicknesser SP 400 Working width 400mm Working height 250mm Electric lifting and lowering of the worktop 4-knife shaft with traditional knives Plough shaft speed 5000r.p.m 4kw main motor Extraction spigot fi120 Machine dimensions 800 x 1000 x 1080mmH Weight 410kg Net price

Weinig Uniplan Hydromat with jointer 220mm

Four-sided planer Weinig with glazing bead saw Type: P 23 Year of Make: 1995 Planing width 230 mm Planing height 130 mm 6 planing shafts + glazing bead saw Shaft arrangement 1 Bottom 4 kW 2 right-hand lifting spindle clocked with 3 Left 7.5 kW 4 Top-clocked shaft 5.5 kW 5 Bottom 5.5 kW Glass bead saw Spindle diameter 40 mm Right and left shafts are driven by 1 motor with manual Waxilit pump with distributor for extraction pipes fully equipped with planer heads as well as 4 additional milling heads good, ready-to-use condition

SCM FS410 NOVA planer Working width 410mm Working height of the thicknesser 220mm Thicknessing table mounted on 4 supports Two planing speeds with a thicknesser of 6-12m/min 4-knife shaft Shaft with tersa knives Planing shaft diameter 95mm Shaft speed 5000r.p.m Additional fence for planing low workpieces with a planer Motor power 4kw Planer tops length 2200mm Slotting and drilling unit CE Certified Technical documentation

TOS Four-Sided Automatic Planer with 2 axes ( height and width ) 220 x 120 mm F-M 25 x 6 mm Profile parcel at position 2-3-4-5 Pneumatic feed roller Stepless feed 5 to 25 m. Dressing table 2000 mm