DMG MORI DMP 70 범용 니 타입 밀링 머신

· Working area 1

· Longitudinal
· 700 mm

· Cross
· 420 mm

· Vertical
· 380 mm

· General

· High dynamic Vertical Drill-Tap centre with best milling performance; Control: 3D-control Siemens 840D sl Operate
·

· Technical Data

· Feed rate longitudinal/transverse/vertical
· 60000/60000/60000 mm/min

· Rapid traverse longitudinal/transverse/vertical
· 60/60/60 m/min

· Main drive
· Drive power (100% DC) 6 kW

·
· Drive power (40% DC) 8,5 kW

·
· Clamping System ISO 7388-3 - JD30

·
· Spindle taper BT 30

·
· Speed range 20 - 10000 rpm

·
· Torque (40% DC) 48 Nm

·
· Torque (100% DC) 41 Nm

· Integrated swivel rotary table simultaneous
· Integated swivel rotary table 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Inclusive Software package Sinumerik Mdynamics 5-ax

· Rotary joint, 4 channels
· Rotary joint for integrated swivel rotary table with torque drives 4- channels, in Standard 2x for air, 2x for oil Including fix plate and fast coupling at machine rear side

· Clamping pneumatic, one circuit
· Clamping pneumatic 1-circuit Including 2x 3/2 way valve

· Tool magazine 25 places
· Tool magazine 25 places (suitable for inclusion in the tool spindle) Chip-to-chip time 1.6 sec

· Production package band filter ICS 40bar
· Paper band filter ICS 40bar includes: Paper band filter 40bar/ 23l/min Additional tank 600l Chip conveyor useable for fine chips (self cleaning slotted filter) Discharge height: 600mm; Tank volume 200l Flushing in working room Spray gun for swarf removal

· Air blast through spindle centre
· Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible!

· Preparation 3D Quickset
· Machine preparation for use of the 3D quickSET Toolkit. included is the Softwareoption for 3D quickSET for one machine. 5 axis machine configurations (only with option touch probe)

· Signal lamp 4-colour
· Signal lamp, 4 colours

· DMG MORI Interface PROFIBUS Right
· DMG MORI Interface PROFIBUS loading door at right machine side PROFIBUS communication between robot and machine for loading cycle 2 channel safety circuits Only in combination with an additional clamping method option!.

· Operation mode 4
· Operation mode 4 Process monitoring in the production Manual intervention with open doors of machining area. Release after check list has been filled in.

· Tropical package
· Package for tropical climate for ambient temperature max. 50°Celsius: includes active cooling for electrical cabinet, active cooling main spindle drive / motor spindle

· Special equipment
· RMS-Sensor

· Workpiece loading & unloading system WH 3 CELL
· Workpiece loading & unloading system WH 3 CELL with 6-axis industrial robots and workpiece carrier storing system (paternoster); maximum possible workpiece weight of 3 kg, maximum workpiece size 100 x 100 x 50 mm Robot FANUC LR Mate 200 iD/7L PROFIBUS in

· WH 3 CELL Integration kit for DMP 35/70
· WH 3 CELL Integration kit for DMP 35/70 Machine-specific adaptation for the protective housing on one DMP 35/70

· Dual gripper PGN 80 (without gripper fingers)
· Dual gripper Type Schunk PGN 80 with 8 mm travel per jaw (gripper fingers not included!)

· Gripper system Schunk PGN-plus 80
· Gripping device Schunk PGN-plus 80