PEMA HPS 3500 和 TPS 3500 焊接定位机由芬兰 Pemamek Oy Ltd 于2021年制造。该系统由两台极为多功能的机器组成— —HPS 3500头架和TPS 3500尾托，合计载重7吨。该方案专注于提升和旋转长 件，非常适合生产风塔、拖车框架或管材等。这两台 机器可以协同工作，也可以独立工作。无阶高度调节 保工作参数与工件尺寸的精确调整。 PEMA HPS 3500 和 TPS 3500 焊接定位器的技术规格 - 最大载重：7吨（头座3.5吨+尾座3.5吨） - 转速：0.06-1.3转/分钟 - 倾斜轴高度调节范围：700-1500毫米 - 工作台板直径：950毫米 - 工作台板上的T型槽：M20 DIN508（4件） - 最大扭矩：2800牛·米 - 倾斜扭矩：7500牛米 - 市电供电电缆长度：12米 - 功率：25 A - 焊接电流接地容量：700安培 - 电源：3×400伏;50 Hz - PEMA机 ...
: neu : ca. 3-6 Wochen ab Auftrag : Türkei : 11000 €: 211.2 €: 1000 kg: 150 mm: 150 mm: 360 kgm: 230 / 50 V / Hz: 0.55 kW: 0.75 kW: 0.1 - 3 U/min: 60 s: 1200 mm: M20X6 mm: 1000 mmThe positioners are available in standard sizes for load capacities from 150 kg to 3,000 kg.The frame is optimally designed for rotation and tilting operations.The positioners consist of a motor, gearbox, table tilting system, steel gears, and control system and are structurally optimally protected.For heavy workpieces, the positioners are mounted on the floor.The tables have radial T-slots that enable quick clamping of the workpieces.Tilting and rotation are controlled by steel gears.For safety, the positioner is equipped with a reduction gear that holds the table in the desired position.Foot pedalCable for signal to welderTouchpanel for following functions:- rotation speed- operating modi (manual, segment ...
Key data: 295 mm, 100 kg
焊接旋转器 SAF POSISAF 1E 搁板直径：Ø 295 mm 最大容量：100公斤 手动旋转 按速度旋转 varitator 右/左 配备一个 Ø 200 mm 的 3 爪同心卡盘 电压：220 V 单声道 支架尺寸：长 800 x 宽 450 x 高 1200 毫
: neu : 2025 : 020157 : prompt, Zwischenverkauf v : Türkei : 6320 €: 121.98 €: 1 : 250 kg: 150 mm: 150 mm: 360 °: 360 kgm: 230 / 50 V / Hz: 0.37 kW: 0.25 kW: 0.1 - 3 U/min: 30 s: 600 mm: M16x6 mm: 550 mmThe positioners are available in standard sizes for load capacities from 150 kg to 3,000 kg.The frame is optimally designed for rotation and tilting operations.The positioners consist of a motor, gearbox, table tilting system, steel gears, and control system and are structurally optimally protected.For heavy workpieces, the positioners are mounted on the floor.The tables have radial T-slots that enable quick clamping of the workpieces.Tilting and rotation are controlled by steel gears.For safety, the positioner is equipped with a reduction gear that holds the table in the desired position.Foot pedalCable for signal to welderTouchpanel for following functions:- rotation speed- operat ...
带升降装置的双柱旋转定位器 Lg.Nr 25138 规格： - 每个支架的最大负载能力 4000 kg - 最大总负载能力 7000 千克 - 行程 / 行程 1780 mm - 提升速度 1600 / 2800 mm/min - 旋转运动电动。可调 - 右 + 左 – 运行 - 驱动 400 V - 请求的空间要求。单位约 宽 1500 x 高 4000 x 深 1500 毫米 - 移动单元的空间要求 W 1300 x H 4000 x D 1300 mm - 重量驱动装置约 4000 千克 - 运行单位的重量 2500 千克
: neu : ca. 3-6 Wochen ab Auftrag : Türkei : 24400 €: 468.48 €: 3000 kg: 150 mm: 150 mm: 360 °: 135 kgm: 400 / 50 V / Hz: 1.1 kW: 1.1 kW: 1200 mm: 700 - 950 mmThe hydraulic positioners are available in standard sizes for load capacities from 1.000 kg to 3.000 kg.The frame is optimally designed for rotation and tilting operations.The positioners consist of a motor, gearbox, table tilting system, steel gears, and control system and are structurally optimally protected.For heavy workpieces, the positioners are mounted to the floor.Tilting and rotation are controlled by steel gears.For safety, the positioner is equipped with a reduction gear that holds the table in the desired position.The rotation speed can be adjusted via a potentiometer.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
BODE TT60 焊接变位机用于在焊接过程中纵最大重量为 3000 kg 的工件。该设备可以在最佳位置工作，从而有助于提 焊接质量。多功能性与经过深思熟虑的设计解决方 相结合，使 BODE 焊接变位机保证了多年使用的安全处理和无故障运行 BODE TT60 焊接转台的技术规格 - 最大工件重量：3000 kg - 工作台直径： 2800 mm
: neu : ca. 3-6 Wochen ab Auftrag : Türkei : 5010 €: 96.69 €: 100 kg: 150 mm: 150 mm: 360 °: 120 kgm: 230 / 50 V / Hz: 0.25 kW: 0.25 kW: 0.1 - 3 U/min: 30 s: 350 mm: M12x6 mm: 690 mmThe positioners are available in standard sizes for load capacities from 150 kg to 3,000 kg.The frame is optimally designed for rotation and tilting operations.The positioners consist of a motor, gearbox, table tilting system, steel gears, and control system and are structurally optimally protected.For heavy workpieces, the positioners are mounted on the floor.The tables have radial T-slots that enable quick clamping of the workpieces.Tilting and rotation are controlled by steel gears.For safety, the positioner is equipped with a reduction gear that holds the table in the desired position.Foot pedalCable for signal to welderTouchpanel for following functions:- rotation speed- operating modi (manual, seg ...
供应信息 23348 规格： - 最大负载能力 1500 Kg - 面板直径 850 mm - 从地板到中心旋转轴的距离 800 mm - 旋转运动电动器。无级可调 0.08 - 1.6 rpm - 右 - + 左 - 运行 - 焊接电流传输约100000000000000000000000000 700 安培 - 驱动 400 V / 2.2 kW - 空间要求单位约。 宽 850 x 高 1450 x 深 1000 mm - 空间要求：移动单元宽 850 x 高 1450 x 深 1000 mm - 从动单元重量约100 550 千克 - 移动单元的重量约定 400 千
: neu : 2025 : 020156 : prompt, Zwischenverkauf v : Türkei : 6720 €: 129.7 €: 1 : 250 kg: 205 kg: 150 mm: 150 mm: 360 °: 360 kgm: 230 / 50 V / Hz: 0.37 kW: 0.25 kW: 0.1 - 3 U/min: 30 s: 600 mm: M16x6 mm: 550 mm: 1000 mm: 700 mm: 1700 mmThe positioners are available in standard sizes for load capacities from 150 kg to 3,000 kg.The frame is optimally designed for rotation and tilting operations.The positioners consist of a motor, gearbox, table tilting system, steel gears, and control system and are structurally optimally protected.For heavy workpieces, the positioners are mounted on the floor.The tables have radial T-slots that enable quick clamping of the workpieces.Tilting and rotation are controlled by steel gears.For safety, the positioner is equipped with a reduction gear that holds the table in the desired position.Foot pedalCable for signal to welderTouchpanel for following f ...
Key data: 1500 mm, 3500 kg
库存号： 3871 焊接转盘 制造商： ESAB PEMA， 型号： 3500 F 机器编号： A7001， 制造年份： 1987 规格： 工作台尺寸 1500 mm Ø 大工件重量 3500 kg Gr. 旋转扭矩 3100 NM 无级可变的工作台旋转。 0.01 - 0.8 公关/分钟 液压驱动装置和尖端 长度： 2000 mm， 高度： 1100， 宽度： 1500 mm， 重量： 1200 kg
table diameter: 900 mmtable load: 1.000 kgFrontal Loading Center (A): 150 mmSide Loading Center (B): 150 mmRotating speeds: 0,1 - 1,1 UpMT-slots: 6 x M16 Tilt Angle: 90-180-105 °Tilting Speed: 30 sn min./90°dimensions: 2100x920x1100 mmweight of the machine ca.: 930 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
规格： - 负载能力定位表约 750公斤 - 面盘直径 500 mm - 工件直径 1600 mm - 高度转盘，水平位置约为 750 毫米 - 带右转盘，- + 左旋转 - 旋转轴转盘无尽360 - 每转旋转时间 12.5 秒 - 向左+向右旋转 - 旋转轴旋转角度 180 - 旋转时间为180旋转角度10秒。 - 2 x 双脚按钮，用于转盘 + 旋转臂 - 海德。夹紧螺栓，用于在转盘中间夹紧工件 - 夹紧螺栓的夹紧行程/夹紧行程 32 mm - 锁模力压制/拉动 80 / 48.9 kN - 夹紧气缸内螺纹 M 27 x 40 - 西门子定位控制 - 手动操作或通过控制操作 - 空间要求约为 宽 1500 x 深 2800 x 高 1100 mm - 重量约 2500公
table diameter: 500 mmtable load: 300 horizontal kg.table load: 150 vertikal kg.swivelling range: 0 - 90 Gradturning speeds: 0,2 - 2,5 U/minbore: 90,0 mmtable height: ~ 650 mm mmmotor: 230 Voltweight of the machine ca.: 90,0 kg.range L-W-H: 385 x 340 x 375 mmFurnishing:- The table can be tilted and clamped at an angle of 0 ° to 90 °- manual tilting- Start / stop via location-independent foot switch- Direction of rotation can be selected right / left- Adjustable rotation time- The control of the welding machine via control- 350 amp ground connectionScope of delivery:- control (integrated)- foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
载重量： 6000 公斤 面盘尺寸：1500 x 1500 mm 倾斜范围：水平至 - 145 转速： 0 - 约 1 rpm 电气。连接： 400 V， 约 5 kW 空间要求：2800 x 2350 x 3250 mm 重量： 5000 kg
table load: 1000 kgtable diameter: 900 mmturning speeds: 0,12 - 1,2 U/minswivelling range: 0 - 135 Gradspeed: Kipp 0,35 U/minwelding current: 500 Adimensions of the machine ca.: 1475 x 1050 x 900 mmFor heavy industryWhen choosing a turntable, it is essentialTurning and tilting torque must be taken into account. To noteapplies to how far the center of gravity of the workpiece is from theThe faceplate is away or how far the center of gravity isis eccentric from the center. By means of aRotary and tilting tables can be used to optimize workpiecesposition for welding.- Robust construction.- Infinitely variable.- Hand remote control.- HF protected.Furnishing :- 1 control (integrated)- 1 wired remote controlThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
水平面盘的最大负载能力为60吨，垂直面盘的最大负 能力为90，负载中心为1米30吨 - 负载中心为2米19吨
工作台直径： - 毫米工作台负载： 3000 公斤摆动范围： 360 分级垂直运动范围： 1380 毫米行程速度： 1900 毫米/分钟： 360 总功率要求： 4 kW机器重量： 5400 公斤机器尺寸： 3800 x 3700 x 4200 毫
table load: max. 40 t twith manual operation panel: ja weight of the machine ca.: 22 t: 1918 Year: ca. 1990 Please note:The machine is dismantled and ready for loading. It is not possible to show it under power or make a video.Our offer includes already the best pictures. So we don’t have and won’t send additional pictures.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: Dreh- und kippbar : für Schweißpistole oder : für Plasma condition: nicht geprüft Please note:The machine is dismantled and ready for loading. It is not possible to show it under power or make a video.Our offer includes already the best pictures. So we don’t have and won’t send additional pictures.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
weight max. in kg: 2500 kgWorking height minimal: 350 mmWorking height maximum: 1850 mmmax. torque: 3000 Nm0: 1 U/minadjustment speed: vertikal 560 mm/minvertical adjustment: 1500 mmbaseplate diameter: 600 mmrotation movement: 0,75 kWstroke drive: 1,85 kWheight of the plant: 2505 mmweight: 1160 kgVideo available on our website.: Sideros Engineering Head & Tailstock Positioners are used to weld and assembly long and large weldments in many different application fields. Besides the benefits of ergonomics and safety during welding and assembly applications, the revolutionary feature of Syncrolift is the compactness and the portability of both columns, thanks to their dedicated hydraulic jacks. The result is an extreme flexibility in the factory.Syncrolift features two main axis: Electrical elevation/descent, and Electrical 360° left/right rotation.Due to its special design, the column po ...
负载能力：1250 kg工作高度 最小：： 540 mm工作高度 最大：1120 mm工作台直径：800 mm旋转范围：--> 95度扭矩：490 Nm工作台转速：2 rpm工作高度从：540 - 1120 垂直 mm工作高度从：700 - 1280 horiz. mm总功率要求：2.53 kW机器重量约：757 kg空间要求约：1.76 x 1.63 m液压定位器，用于永久右转+左转，倾斜，提升和下 。通过逆变器Mod无级转弯的附加费。可根据要求提供 EL/MR 和脚踏板控制。仓库管理员，展厅面积为2500平方米。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理
table diameter: 800 mmtable load: 2 tswivelling range: --> 95 Gradmax. torque: 1250 Nmtable rotation speed: 2 U/minWorking height from to: 550 - 1300 vertikal mmWorking height from to: 650 - 1400 horiz. mmtotal power requirement: 2,53 kWweight of the machine ca.: 930 kgdimensions of the machine ca.: 1,85 x 1,66 mElectric 400 Volt: Hand control panel: Hydraulic-device: Hydraulic positioner for permanent turning right + left, tilting,Raise and lower.Machine dealer with own stock of 2500 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 1300 mmtable load: 7.000 kgFrontal Loading Center (A): 150 mmSide Loading Center (B): 150 mmRotating speeds: 0,1 - 0,9 UpMT-slots: 6 x M24 Tilt Angle: 90-180-100 °Tilting Speed: 30 sn min./90°weight of the machine ca.: 3.050 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 960 mmtable load: 3.500 kgFrontal Loading Center (A): 150 mmSide Loading Center (B): 150 mmRotating speeds: 0,1 - 0,9 UpMT-slots: 6 x M20 Tilt Angle: 70-90-180 °Tilting Speed: 30 sn min./90°weight of the machine ca.: 1.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 715 mmtable load: 500 kgFrontal Loading Center (A): 150 mmSide Loading Center (B): 150 mmRotating speeds: 0,1 - 1 UpMT-slots: 6 x M16 Tilt Angle: 90-180-110 °Tilting Speed: 30 sn min./90°weight of the machine ca.: 675 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
